[PATCH 1/3] iio: adc: vf610: use ADC clock within specification
Stefan Agner
stefan at agner.ch
Tue Jan 27 13:20:24 PST 2015
On 2015-01-27 21:59, Jonathan Cameron wrote:
> On 20/01/15 16:02, Stefan Agner wrote:
>> Depending on conversion mode used, the ADC clock (ADCK) needs
>> to be below a maximum frequency. According to Vybrid's data
>> sheet this is 20MHz for the low power conversion mode.
>>
>> The ADC clock is depending on input clock, which is the bus
>> clock by default. Vybrid SoC are typically clocked at at 400MHz
>> or 500MHz, which leads to 66MHz or 83MHz bus clock respectively.
>> Hence, a divider of 8 is required to stay below the specified
>> maximum clock of 20MHz.
> I hate to point out the obvious, by 83/8 > 20. Missing something?
"stay below the specified maximum clock of 20MHz."
^
The next smaller divider is 4, but then we would en up with more than
20MHz... Unfortunate, but I really don't want to violate the spec :-)
>>
>> Due to the different bus clock speeds, the resulting sampling
>> frequency is not static. Hence use the ADC clock and calculate
>> the actual available sampling frequency dynamically.
>>
>> This fixes bogous values observed on some 500MHz clocked Vybrid
>> SoC. The resulting value usually showed Bit 9 being stuck at 1,
>> or 0, which lead to a value of +/-512.
>>
>> Signed-off-by: Stefan Agner <stefan at agner.ch>
> In principle this looks fine to me. I would however like an
> Ack from Fugang as the original author of the driver).
Ok, Fugang is in CC too (B38611 at freescale.com).
> Given timing I probably wouldn't send this upstream until after
> the merge window now (as it's stable material this won't really
> matter).
That's fine for me, thx.
--
Stefan
>
> Jonathan
>> ---
>> drivers/iio/adc/vf610_adc.c | 91 ++++++++++++++++++++++++++++++---------------
>> 1 file changed, 61 insertions(+), 30 deletions(-)
>>
>> diff --git a/drivers/iio/adc/vf610_adc.c b/drivers/iio/adc/vf610_adc.c
>> index 8ec353c..e63b8e7 100644
>> --- a/drivers/iio/adc/vf610_adc.c
>> +++ b/drivers/iio/adc/vf610_adc.c
>> @@ -141,9 +141,13 @@ struct vf610_adc {
>> struct regulator *vref;
>> struct vf610_adc_feature adc_feature;
>>
>> + u32 sample_freq_avail[5];
>> +
>> struct completion completion;
>> };
>>
>> +static const u32 vf610_hw_avgs[] = { 1, 4, 8, 16, 32 };
>> +
>> #define VF610_ADC_CHAN(_idx, _chan_type) { \
>> .type = (_chan_type), \
>> .indexed = 1, \
>> @@ -180,35 +184,47 @@ static const struct iio_chan_spec vf610_adc_iio_channels[] = {
>> /* sentinel */
>> };
>>
>> -/*
>> - * ADC sample frequency, unit is ADCK cycles.
>> - * ADC clk source is ipg clock, which is the same as bus clock.
>> - *
>> - * ADC conversion time = SFCAdder + AverageNum x (BCT + LSTAdder)
>> - * SFCAdder: fixed to 6 ADCK cycles
>> - * AverageNum: 1, 4, 8, 16, 32 samples for hardware average.
>> - * BCT (Base Conversion Time): fixed to 25 ADCK cycles for 12 bit mode
>> - * LSTAdder(Long Sample Time): fixed to 3 ADCK cycles
>> - *
>> - * By default, enable 12 bit resolution mode, clock source
>> - * set to ipg clock, So get below frequency group:
>> - */
>> -static const u32 vf610_sample_freq_avail[5] =
>> -{1941176, 559332, 286957, 145374, 73171};
>> +static inline void vf610_adc_calculate_rates(struct vf610_adc *info)
>> +{
>> + unsigned long adck_rate, ipg_rate = clk_get_rate(info->clk);
>> + int i;
>> +
>> + /*
>> + * Calculate ADC sample frequencies
>> + * Sample time unit is ADCK cycles. ADCK clk source is ipg clock,
>> + * which is the same as bus clock.
>> + *
>> + * ADC conversion time = SFCAdder + AverageNum x (BCT + LSTAdder)
>> + * SFCAdder: fixed to 6 ADCK cycles
>> + * AverageNum: 1, 4, 8, 16, 32 samples for hardware average.
>> + * BCT (Base Conversion Time): fixed to 25 ADCK cycles for 12 bit mode
>> + * LSTAdder(Long Sample Time): fixed to 3 ADCK cycles
>> + */
>> + adck_rate = ipg_rate / info->adc_feature.clk_div;
>> + for (i = 0; i < ARRAY_SIZE(vf610_hw_avgs); i++)
>> + info->sample_freq_avail[i] =
>> + adck_rate / (6 + vf610_hw_avgs[i] * (25 + 3));
>> +}
>>
>> static inline void vf610_adc_cfg_init(struct vf610_adc *info)
>> {
>> + struct vf610_adc_feature *adc_feature = &info->adc_feature;
>> +
>> /* set default Configuration for ADC controller */
>> - info->adc_feature.clk_sel = VF610_ADCIOC_BUSCLK_SET;
>> - info->adc_feature.vol_ref = VF610_ADCIOC_VR_VREF_SET;
>> + adc_feature->clk_sel = VF610_ADCIOC_BUSCLK_SET;
>> + adc_feature->vol_ref = VF610_ADCIOC_VR_VREF_SET;
>> +
>> + adc_feature->calibration = true;
>> + adc_feature->ovwren = true;
>> +
>> + adc_feature->res_mode = 12;
>> + adc_feature->sample_rate = 1;
>> + adc_feature->lpm = true;
>>
>> - info->adc_feature.calibration = true;
>> - info->adc_feature.ovwren = true;
>> + /* Use a save ADCK which is below 20MHz on all devices */
>> + adc_feature->clk_div = 8;
>>
>> - info->adc_feature.clk_div = 1;
>> - info->adc_feature.res_mode = 12;
>> - info->adc_feature.sample_rate = 1;
>> - info->adc_feature.lpm = true;
>> + vf610_adc_calculate_rates(info);
>> }
>>
>> static void vf610_adc_cfg_post_set(struct vf610_adc *info)
>> @@ -290,12 +306,10 @@ static void vf610_adc_cfg_set(struct vf610_adc *info)
>>
>> cfg_data = readl(info->regs + VF610_REG_ADC_CFG);
>>
>> - /* low power configuration */
>> cfg_data &= ~VF610_ADC_ADLPC_EN;
>> if (adc_feature->lpm)
>> cfg_data |= VF610_ADC_ADLPC_EN;
>>
>> - /* disable high speed */
>> cfg_data &= ~VF610_ADC_ADHSC_EN;
>>
>> writel(cfg_data, info->regs + VF610_REG_ADC_CFG);
>> @@ -435,10 +449,27 @@ static irqreturn_t vf610_adc_isr(int irq, void *dev_id)
>> return IRQ_HANDLED;
>> }
>>
>> -static IIO_CONST_ATTR_SAMP_FREQ_AVAIL("1941176, 559332, 286957, 145374, 73171");
>> +static ssize_t vf610_show_samp_freq_avail(struct device *dev,
>> + struct device_attribute *attr, char *buf)
>> +{
>> + struct vf610_adc *info = iio_priv(dev_to_iio_dev(dev));
>> + size_t len = 0;
>> + int i;
>> +
>> + for (i = 0; i < ARRAY_SIZE(info->sample_freq_avail); i++)
>> + len += scnprintf(buf + len, PAGE_SIZE - len,
>> + "%u ", info->sample_freq_avail[i]);
>> +
>> + /* replace trailing space by newline */
>> + buf[len - 1] = '\n';
>> +
>> + return len;
>> +}
>> +
>> +static IIO_DEV_ATTR_SAMP_FREQ_AVAIL(vf610_show_samp_freq_avail);
>>
>> static struct attribute *vf610_attributes[] = {
>> - &iio_const_attr_sampling_frequency_available.dev_attr.attr,
>> + &iio_dev_attr_sampling_frequency_available.dev_attr.attr,
>> NULL
>> };
>>
>> @@ -502,7 +533,7 @@ static int vf610_read_raw(struct iio_dev *indio_dev,
>> return IIO_VAL_FRACTIONAL_LOG2;
>>
>> case IIO_CHAN_INFO_SAMP_FREQ:
>> - *val = vf610_sample_freq_avail[info->adc_feature.sample_rate];
>> + *val = info->sample_freq_avail[info->adc_feature.sample_rate];
>> *val2 = 0;
>> return IIO_VAL_INT;
>>
>> @@ -525,9 +556,9 @@ static int vf610_write_raw(struct iio_dev *indio_dev,
>> switch (mask) {
>> case IIO_CHAN_INFO_SAMP_FREQ:
>> for (i = 0;
>> - i < ARRAY_SIZE(vf610_sample_freq_avail);
>> + i < ARRAY_SIZE(info->sample_freq_avail);
>> i++)
>> - if (val == vf610_sample_freq_avail[i]) {
>> + if (val == info->sample_freq_avail[i]) {
>> info->adc_feature.sample_rate = i;
>> vf610_adc_sample_set(info);
>> return 0;
>>
More information about the linux-arm-kernel
mailing list