[PATCH v2] ARM: dts: sun7i: Add dts file for pcDuino 3 Nano board
Adam Sampson
ats at offog.org
Mon Jan 26 01:55:17 PST 2015
Add support for the LinkSprite pcDuino 3 Nano board. This is a low-cost
Allwinner A20 board with Arduino-style GPIO headers; it features 1G RAM,
4G NAND flash, 1 micro-SD, 2 USB sockets, 1 micro USB socket for OTG and
another for power in, HDMI, SATA, 5V power for SATA devices, gigabit
Ethernet, an IR receiver, 3.5mm audio out and a MIPI camera connector.
For more details, see: http://linux-sunxi.org/LinkSprite_pcDuino3_Nano
Signed-off-by: Adam Sampson <ats at offog.org>
---
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts | 212 +++++++++++++++++++++++++
2 files changed, 214 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7df26a2..c025724 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -479,7 +479,8 @@ dtb-$(CONFIG_MACH_SUN7I) += \
sun7i-a20-olinuxino-lime.dtb \
sun7i-a20-olinuxino-lime2.dtb \
sun7i-a20-olinuxino-micro.dtb \
- sun7i-a20-pcduino3.dtb
+ sun7i-a20-pcduino3.dtb \
+ sun7i-a20-pcduino3-nano.dtb
dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a23-ippo-q8h-v5.dtb \
sun8i-a23-ippo-q8h-v1.2.dtb
diff --git a/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts b/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts
new file mode 100644
index 0000000..6055de5
--- /dev/null
+++ b/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts
@@ -0,0 +1,212 @@
+/*
+ * Copyright 2015 Adam Sampson <ats at offog.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ model = "LinkSprite pcDuino3 Nano";
+ compatible = "linksprite,pcduino3-nano", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart2;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_pcduino3_nano>;
+
+ led3 {
+ label = "pcduino3-nano:led3:usr";
+ gpios = <&pio 7 16 GPIO_ACTIVE_LOW>; /* PH16 */
+ };
+
+ led4 {
+ label = "pcduino3-nano:led4:usr";
+ gpios = <&pio 7 15 GPIO_ACTIVE_LOW>; /* PH15 */
+ };
+ };
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ status = "okay";
+
+ phy1: ethernet-phy at 1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic at 34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ ahci_pwr_pin_pcduino3_nano: ahci_pwr_pin at 0 {
+ allwinner,pins = "PH2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_pcduino3_nano: led_pins at 0 {
+ allwinner,pins = "PH16", "PH15";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb1_vbus_pin_pcduino3_nano: usb1_vbus_pin at 0 {
+ allwinner,pins = "PH11";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_ahci_5v {
+ pinctrl-0 = <&ahci_pwr_pin_pcduino3_nano>;
+ gpio = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
+ status = "okay";
+};
+
+®_usb1_vbus {
+ pinctrl-0 = <&usb1_vbus_pin_pcduino3_nano>;
+ gpio = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins_a>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--
1.7.10.4
More information about the linux-arm-kernel
mailing list