[PATCH 07/12] pm: at91: the standby mode uses the same sram function as the suspend to memory mode

Sylvain Rochet sylvain.rochet at finsecur.com
Fri Jan 23 09:32:34 PST 2015


Hello Wenyou,

On Tue, Jan 20, 2015 at 04:17:00PM +0800, Wenyou Yang wrote:
> 
> diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
> index 691e6db..a1010f0 100644
> --- a/arch/arm/mach-at91/pm.c
> +++ b/arch/arm/mach-at91/pm.c
  (...)
>  static int at91_pm_enter(suspend_state_t state)
>  {
>  	at91_pinctrl_gpio_suspend();
>  
>  	switch (state) {
> +	/*
> +	 * Suspend-to-RAM is like STANDBY plus slow clock mode, so
> +	 * drivers must suspend more deeply, the master clock switches
> +	 * to the clk32k and turns off the main oscillator
> +	 *
> +	 * STANDBY mode has *all* drivers suspended; ignores irqs not
> +	 * marked as 'wakeup' event sources; and reduces DRAM power.
> +	 * But otherwise it's identical to PM_SUSPEND_ON:  cpu idle, and
> +	 * nothing fancy done with main or cpu clocks.
> +	 */
> +	case PM_SUSPEND_MEM:
> +	case PM_SUSPEND_STANDBY:
   (...)
> -		case PM_SUSPEND_MEM:
> -			/*
> -			 * Ensure that clocks are in a valid state.
> -			 */
> -			if (!at91_pm_verify_clocks())
> -				goto error;
   (...)
> +		if (!at91_pm_verify_clocks())
> +			goto error;
>  
   (...)
> -		case PM_SUSPEND_STANDBY:
> -			/*
> -			 * NOTE: the Wait-for-Interrupt instruction needs to be

By doing that at91_pm_verify_clocks() is now called for both MEM and 
STANDBY targets.

In my opinion this function is misnamed and should be called 
at91_pm_verify_clocks_for_slow_clock_mode(). This function actually 
checks if we can safely switch to slow clock mode, if some peripherals 
are still using the master clock, we abort the suspend because we can't 
suspend in good condition. Hard unclocking peripherals which ask for a 
soft stop, like USB controllers, is something we should avoid doing.

This function checks if USB PLL and PLL B are stopped, if PCK0..PCK3 are 
stopped too (or just using the 32k clock). If all drivers suspended 
correctly this is the state we expect and we can suspend in a deep 
state.

Not this is currently not the case in linux-next, suspend/resume support 
to all Atmel USB drivers (ehci-atmel,ohci-at91,atmel_usba,at91_udc) are 
in my series:
 [PATCHv7 0/6] USB: host: Atmel OHCI and EHCI drivers improvements
   <1421761144-11767-1-git-send-email-sylvain.rochet at finsecur.com>
 [PATCHv6 0/5] USB: gadget: atmel_usba_udc: Driver improvements 
   <1421945805-31129-1-git-send-email-sylvain.rochet at finsecur.com>

We are not going to change any clock for STANDBY target, there is no 
clock to check, so we don't need to call at91_pm_verify_clocks() for 
this target.

Sylvain



More information about the linux-arm-kernel mailing list