[PATCH v4 2/2] ARM: dts: Add HS400 support for exynos5420 and exynos5800

[Alim Akhtar]

Hi Jaehoon

On Wed, Jan 21, 2015 at 4:32 AM, Jaehoon Chung <jh80.chung at samsung.com> wrote:
> Hi,
>
> If you want to enable the hs400 mode, need to add "mmc-hs400-1_8v" or "mmc-hs400-1_2v".
> But this patch didn't add them. do you have any other plan?
>
Yes, right, plan is to send separate patch to enable hs400, as of now
I am not sure if all the 5800-peach-pi boards are populated with
emmc5.0 device or not. So I will enable HS400 after confirming this
point.
> On 01/14/2015 07:30 PM, Alim Akhtar wrote:
>> From: Seungwon Jeon <tgih.jun at samsung.com>
>>
>> HS400 timing values are added for SMDK5420, exynos5420-peach-pit
>> and exynos5800-peach-pi boards.
>> This also adds RCLK GPIO line, this gpio should be in pull-down
>> state.
>>
>> Signed-off-by: Seungwon Jeon <tgih.jun at samsung.com>
>> Signed-off-by: Alim Akhtar <alim.akhtar at samsung.com>
>> [Alim: addressed review comments]
>> ---
>>  arch/arm/boot/dts/exynos5420-peach-pit.dts |    4 +++-
>>  arch/arm/boot/dts/exynos5420-pinctrl.dtsi  |    7 +++++++
>>  arch/arm/boot/dts/exynos5420-smdk5420.dts  |    4 +++-
>>  arch/arm/boot/dts/exynos5800-peach-pi.dts  |    4 +++-
>>  4 files changed, 16 insertions(+), 3 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts
>> index 9a050e1..7ffaba8 100644
>> --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts
>> +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts
>> @@ -569,8 +569,10 @@
>>       samsung,dw-mshc-ciu-div = <3>;
>>       samsung,dw-mshc-sdr-timing = <0 4>;
>>       samsung,dw-mshc-ddr-timing = <0 2>;
>> +     samsung,dw-mshc-hs400-timing = <0 2>;
>> +     read-strobe-delay = <90>;
>>       pinctrl-names = "default";
>> -     pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
>> +     pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8 &sd0_rclk>;
>>       bus-width = <8>;
>>  };
>>
>> diff --git a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi
>> index ba686e4..8b15316 100644
>> --- a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi
>> +++ b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi
>> @@ -201,6 +201,13 @@
>>                       samsung,pin-drv = <3>;
>>               };
>>
>> +             sd0_rclk: sd0-rclk {
>
> I know it used to "sd0_rdqs", not "sd0_rclk".
> Change name.
>
Ok, I will change as per UM of 5800/5420,

> Best Regards,
> Jaehoon Chung
>> +                     samsung,pins = "gpc0-7";
>> +                     samsung,pin-function = <2>;
>> +                     samsung,pin-pud = <1>;
>> +                     samsung,pin-drv = <3>;
>> +             };
>> +
>>               sd1_cmd: sd1-cmd {
>>                       samsung,pins = "gpc1-1";
>>                       samsung,pin-function = <2>;
>> diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts
>> index 8be3d7b..5290e79 100644
>> --- a/arch/arm/boot/dts/exynos5420-smdk5420.dts
>> +++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts
>> @@ -80,8 +80,10 @@
>>               samsung,dw-mshc-ciu-div = <3>;
>>               samsung,dw-mshc-sdr-timing = <0 4>;
>>               samsung,dw-mshc-ddr-timing = <0 2>;
>> +             samsung,dw-mshc-hs400-timing = <0 2>;
>> +             read-strobe-delay = <90>;
>>               pinctrl-names = "default";
>> -             pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
>> +             pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8 &sd0_rclk>;
>>               bus-width = <8>;
>>               cap-mmc-highspeed;
>>       };
>> diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts
>> index e8fdda8..fa1c858 100644
>> --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts
>> +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts
>> @@ -557,8 +557,10 @@
>>       samsung,dw-mshc-ciu-div = <3>;
>>       samsung,dw-mshc-sdr-timing = <0 4>;
>>       samsung,dw-mshc-ddr-timing = <0 2>;
>> +     samsung,dw-mshc-hs400-timing = <0 2>;
>> +     read-strobe-delay = <90>;
>>       pinctrl-names = "default";
>> -     pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
>> +     pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8 &sd0_rclk>;
>>       bus-width = <8>;
>>  };
>>
>>
>



-- 
Regards,
Alim