[PATCH v4 3/3] ARM: dts: meson8: add pinctrl node

[Beniamino Galvani]

Add pinctrl node to the DTSI file for meson8 and sub-nodes for some
standard mux configurations.

Signed-off-by: Beniamino Galvani <b.galvani at gmail.com>
---
 arch/arm/boot/dts/meson8.dtsi | 68 +++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 68 insertions(+)

diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/meson8.dtsi
index 1f442a7..a2ddcb8 100644
--- a/arch/arm/boot/dts/meson8.dtsi
+++ b/arch/arm/boot/dts/meson8.dtsi
@@ -43,6 +43,7 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
+#include <dt-bindings/gpio/meson8-gpio.h>
 /include/ "meson.dtsi"
 
 / {
@@ -89,4 +90,71 @@
 		compatible = "fixed-clock";
 		clock-frequency = <141666666>;
 	};
+
+	pinctrl: pinctrl at c1109880 {
+		compatible = "amlogic,meson8-pinctrl";
+		reg = <0xc1109880 0x10>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gpio: banks at c11080b0 {
+			reg = <0xc11080b0 0x28>,
+			      <0xc11080e8 0x18>,
+			      <0xc1108120 0x18>,
+			      <0xc1108030 0x30>;
+			reg-names = "mux", "pull", "pull-enable", "gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpio_ao: ao-bank at c1108030 {
+			reg = <0xc8100014 0x4>,
+			      <0xc810002c 0x4>,
+			      <0xc8100024 0x8>;
+			reg-names = "mux", "pull", "gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		uart_ao_a_pins: uart_ao_a {
+			mux {
+				groups = "uart_tx_ao_a", "uart_rx_ao_a";
+				function = "uart_ao";
+			};
+		};
+
+		i2c_ao_pins: i2c_mst_ao {
+			mux {
+				groups = "i2c_mst_sck_ao", "i2c_mst_sda_ao";
+				function = "i2c_mst_ao";
+			};
+		};
+
+		spi_nor_pins: nor {
+			mux {
+				groups = "nor_d", "nor_q", "nor_c", "nor_cs";
+				function = "nor";
+			};
+		};
+
+		ir_recv_pins: remote {
+			mux {
+				groups = "remote_input";
+				function = "remote";
+			};
+		};
+
+		eth_pins: ethernet {
+			mux {
+				groups = "eth_tx_clk_50m", "eth_tx_en",
+					 "eth_txd1", "eth_txd0",
+					 "eth_rx_clk_in", "eth_rx_dv",
+					 "eth_rxd1", "eth_rxd0", "eth_mdio",
+					 "eth_mdc";
+				function = "ethernet";
+			};
+		};
+	};
+
 }; /* end of / */
-- 
2.1.4