[PATCH 2/4] ARM: dts: Add basic dm816x device tree configuration
Tony Lindgren
tony at atomide.com
Sat Jan 17 08:41:02 PST 2015
* Tony Lindgren <tony at atomide.com> [150115 15:05]:
>
> For reference, the devices I've confirmed to work so far are:
>
> - intc
> - timers
> - gpmc
> - i2c
> - ethernet and mdio
> - mmc
> - edma
> - uart
>
> Updated patch below with the mailbox fixed.
Got the spi working too. The it needs to be compatible with
ti,omap4-mcspi with four chip selects. Updated patch below.
Also added the pinctrl-single entry.
Regards,
Tony
8< ------------------
From: Tony Lindgren <tony at atomide.com>
Date: Wed, 14 Jan 2015 17:45:22 -0800
Subject: [PATCH] ARM: dts: Add basic dm816x device tree configuration
Similar to other omap variants, let's add dm816x support.
Note that this is based on generated data from the
TI81XX-LINUX-PSP-04.04.00.02 patches published at:
http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/TI81XX_04_04/04_04_00_02/index_FDS.html
I've verified the basic functionality, but have not been
able to test all the devices on dm8168-evm.
Cc: Brian Hutchinson <b.hutchman at gmail.com>
Signed-off-by: Tony Lindgren <tony at atomide.com>
--- /dev/null
+++ b/arch/arm/boot/dts/dm816x.dtsi
@@ -0,0 +1,386 @@
+/*
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/omap.h>
+
+#include "skeleton.dtsi"
+
+/ {
+ compatible = "ti,dm816";
+ interrupt-parent = <&intc>;
+
+ aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ serial0 = &uart1;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ ethernet0 = ð0;
+ ethernet1 = ð1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cpu at 0 {
+ compatible = "arm,cortex-a8";
+ device_type = "cpu";
+ reg = <0>;
+ };
+ };
+
+ pmu {
+ compatible = "arm,cortex-a8-pmu";
+ interrupts = <3>;
+ };
+
+ /*
+ * The soc node represents the soc top level view. It is used for IPs
+ * that are not memory mapped in the MPU view or for the MPU itself.
+ */
+ soc {
+ compatible = "ti,omap-infra";
+ mpu {
+ compatible = "ti,omap3-mpu";
+ ti,hwmods = "mpu";
+ };
+ };
+
+ dm816x_pinmux: pinmux at 44e10800 {
+ compatible = "pinctrl-single";
+ reg = <0x48140800 0x50a>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-single,register-width = <16>;
+ pinctrl-single,function-mask = <0xf>;
+ };
+
+ /*
+ * XXX: Use a flat representation of the dm816x interconnect.
+ * The real dm816x interconnect network is quite complex. Since
+ * it will not bring real advantage to represent that in DT
+ * for the moment, just use a fake OCP bus entry to represent
+ * the whole bus hierarchy.
+ */
+ ocp {
+ compatible = "ti,omap3-l3-smx", "simple-bus";
+ reg = <0x44000000 0x10000>;
+ interrupts = <9 10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ ti,hwmods = "l3_main";
+
+ prcm: prcm at 48180000 {
+ compatible = "ti,dm816-prcm";
+ reg = <0x48180000 0x4000>;
+
+ prcm_clocks: clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ prcm_clockdomains: clockdomains {
+ };
+ };
+
+ scrm: scrm at 48140000 {
+ compatible = "ti,dm816-scrm";
+ reg = <0x48140000 0x21000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x48140000 0x21000>;
+
+ scrm_clocks: clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ scrm_clockdomains: clockdomains {
+ };
+ };
+
+ cm: syscon at 44e10000 {
+ compatible = "ti,am33xx-controlmodule", "syscon";
+ reg = <0x44e10000 0x800>;
+ };
+
+ edma: edma at 49000000 {
+ compatible = "ti,edma3";
+ ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2", "tptc3";
+ reg = <0x49000000 0x10000>,
+ <0x44e10f90 0x40>;
+ interrupts = <12 13 14>;
+ #dma-cells = <1>;
+ };
+
+ elm: elm at 48080000 {
+ compatible = "ti,816-elm";
+ ti,hwmods = "elm";
+ reg = <0x48080000 0x2000>;
+ interrupts = <4>;
+ };
+
+ gpio1: gpio at 48032000 {
+ compatible = "ti,omap3-gpio";
+ ti,hwmods = "gpio1";
+ reg = <0x48032000 0x1000>;
+ interrupts = <97>;
+ };
+
+ gpio2: gpio at 4804c000 {
+ compatible = "ti,omap3-gpio";
+ ti,hwmods = "gpio2";
+ reg = <0x4804c000 0x1000>;
+ interrupts = <99>;
+ };
+
+ gpmc: gpmc at 50000000 {
+ compatible = "ti,am3352-gpmc";
+ ti,hwmods = "gpmc";
+ reg = <0x50000000 0x2000>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ interrupts = <100>;
+ gpmc,num-cs = <6>;
+ gpmc,num-waitpins = <2>;
+ };
+
+ i2c1: i2c at 48028000 {
+ compatible = "ti,omap4-i2c";
+ ti,hwmods = "i2c1";
+ reg = <0x48028000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <70>;
+ dmas = <&edma 58 &edma 59>;
+ dma-names = "tx", "rx";
+ };
+
+ i2c2: i2c at 4802a000 {
+ compatible = "ti,omap4-i2c";
+ ti,hwmods = "i2c2";
+ reg = <0x4802a000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <71>;
+ dmas = <&edma 60 &edma 61>;
+ dma-names = "tx", "rx";
+ };
+
+ intc: interrupt-controller at 48200000 {
+ compatible = "ti,dm816-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x48200000 0x1000>;
+ };
+
+ mailbox: mailbox at 480c8000 {
+ compatible = "ti,omap4-mailbox";
+ reg = <0x480c8000 0x2000>;
+ interrupts = <77>;
+ ti,hwmods = "mailbox";
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <12>;
+ mbox_dsp: mbox_dsp {
+ ti,mbox-tx = <3 0 0>;
+ ti,mbox-rx = <0 0 0>;
+ };
+ };
+
+ mdio: mdio at 4a100800 {
+ compatible = "ti,davinci_mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x4a100800 0x100>;
+ ti,hwmods = "davinci_mdio";
+ bus_freq = <1000000>;
+ phy0: ethernet-phy at 0 {
+ reg = <1>;
+ };
+ phy1: ethernet-phy at 1 {
+ reg = <2>;
+ };
+ };
+
+ eth0: ethernet at 4a100000 {
+ compatible = "ti,dm816-emac";
+ ti,hwmods = "emac0";
+ reg = <0x4a100000 0x800
+ 0x4a100900 0x3700>;
+ clocks = <&sysclk24_ck>;
+ ti,davinci-ctrl-reg-offset = <0>;
+ ti,davinci-ctrl-mod-reg-offset = <0x900>;
+ ti,davinci-ctrl-ram-offset = <0x2000>;
+ ti,davinci-ctrl-ram-size = <0x2000>;
+ interrupts = <40 41 42 43>;
+ phy-handle = <&phy0>;
+ };
+
+ eth1: ethernet at 4a120000 {
+ compatible = "ti,dm816-emac";
+ ti,hwmods = "emac1";
+ reg = <0x4a120000 0x4000>;
+ clocks = <&sysclk24_ck>;
+ ti,davinci-ctrl-reg-offset = <0>;
+ ti,davinci-ctrl-mod-reg-offset = <0x900>;
+ ti,davinci-ctrl-ram-offset = <0x2000>;
+ ti,davinci-ctrl-ram-size = <0x2000>;
+ interrupts = <44 45 46 47>;
+ phy-handle = <&phy1>;
+ };
+
+ mcspi1: spi at 48030000 {
+ compatible = "ti,omap4-mcspi";
+ reg = <0x48030000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <65>;
+ ti,spi-num-cs = <4>;
+ ti,hwmods = "mcspi1";
+ dmas = <&edma 16 &edma 17
+ &edma 18 &edma 19>;
+ dma-names = "tx0", "rx0", "tx1", "rx1";
+ };
+
+ mmc1: mmc at 48060000 {
+ compatible = "ti,omap4-hsmmc";
+ reg = <0x48060000 0x11000>;
+ ti,hwmods = "mmc1";
+ interrupts = <64>;
+ dmas = <&edma 24 &edma 25>;
+ dma-names = "tx", "rx";
+ };
+
+ timer1: timer at 4802e000 {
+ compatible = "ti,dm816-timer";
+ reg = <0x4802e000 0x2000>;
+ interrupts = <67>;
+ ti,hwmods = "timer1";
+ ti,timer-alwon;
+ };
+
+ timer2: timer at 48040000 {
+ compatible = "ti,dm816-timer";
+ reg = <0x48040000 0x2000>;
+ interrupts = <68>;
+ ti,hwmods = "timer2";
+ };
+
+ timer3: timer at 48042000 {
+ compatible = "ti,dm816-timer";
+ reg = <0x48042000 0x2000>;
+ interrupts = <69>;
+ ti,hwmods = "timer3";
+ };
+
+ timer4: timer at 48044000 {
+ compatible = "ti,dm816-timer";
+ reg = <0x48044000 0x2000>;
+ interrupts = <92>;
+ ti,hwmods = "timer4";
+ };
+
+ timer5: timer at 48046000 {
+ compatible = "ti,dm816-timer";
+ reg = <0x48046000 0x2000>;
+ interrupts = <93>;
+ ti,hwmods = "timer5";
+ };
+
+ timer6: timer at 48048000 {
+ compatible = "ti,dm816-timer";
+ reg = <0x48048000 0x2000>;
+ interrupts = <94>;
+ ti,hwmods = "timer6";
+ };
+
+ timer7: timer at 4804a000 {
+ compatible = "ti,dm816-timer";
+ reg = <0x4804a000 0x2000>;
+ interrupts = <95>;
+ ti,hwmods = "timer7";
+ };
+
+ uart1: uart at 48020000 {
+ compatible = "ti,omap3-uart";
+ ti,hwmods = "uart1";
+ reg = <0x48020000 0x2000>;
+ clock-frequency = <48000000>;
+ interrupts = <72>;
+ dmas = <&edma 26 &edma 27>;
+ dma-names = "tx", "rx";
+ };
+
+ uart2: uart at 48022000 {
+ compatible = "ti,omap3-uart";
+ ti,hwmods = "uart2";
+ reg = <0x48022000 0x2000>;
+ clock-frequency = <48000000>;
+ interrupts = <73>;
+ dmas = <&edma 28 &edma 29>;
+ dma-names = "tx", "rx";
+ };
+
+ uart3: uart at 48024000 {
+ compatible = "ti,omap3-uart";
+ ti,hwmods = "uart3";
+ reg = <0x48024000 0x2000>;
+ clock-frequency = <48000000>;
+ interrupts = <74>;
+ dmas = <&edma 30 &edma 31>;
+ dma-names = "tx", "rx";
+ };
+
+ /* NOTE: USB needs a transceiver driver for phys to work */
+ usb: usb_otg_hs at 47401000 {
+ compatible = "ti,am33xx-usb";
+ reg = <0x47401000 0x400000>;
+ ranges;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ti,hwmods = "usb_otg_hs";
+
+ usb0: usb at 47401000 {
+ compatible = "ti,musb-am33xx";
+ reg = <0x47401400 0x400
+ 0x47401000 0x200>;
+ reg-names = "mc", "control";
+ interrupts = <18>;
+ interrupt-names = "mc";
+ dr_mode = "otg";
+ mentor,multipoint = <1>;
+ mentor,num-eps = <16>;
+ mentor,ram-bits = <12>;
+ mentor,power = <500>;
+ };
+
+ usb1: usb at 47401800 {
+ compatible = "ti,musb-am33xx";
+ status = "disabled";
+ reg = <0x47401c00 0x400
+ 0x47401800 0x200>;
+ reg-names = "mc", "control";
+ interrupts = <19>;
+ interrupt-names = "mc";
+ dr_mode = "otg";
+ mentor,multipoint = <1>;
+ mentor,num-eps = <16>;
+ mentor,ram-bits = <12>;
+ mentor,power = <500>;
+ };
+ };
+
+ wd_timer2: wd_timer at 480c2000 {
+ compatible = "ti,omap3-wdt";
+ ti,hwmods = "wd_timer";
+ reg = <0x480c2000 0x1000>;
+ interrupts = <0>;
+ };
+ };
+};
+
More information about the linux-arm-kernel
mailing list