[PATCH v4 4/4] ARM: mvebu: Armada 385 GP: Add regulators to the SATA port

[Hans de Goede]

Hi,

On 15-01-15 15:09, Gregory CLEMENT wrote:
> Add the regulators to each SATA port.
>
> Signed-off-by: Gregory CLEMENT <gregory.clement at free-electrons.com>
> ---
>   arch/arm/boot/dts/armada-388-gp.dts | 126 ++++++++++++++++++++++++++++++++++++
>   1 file changed, 126 insertions(+)
>
> diff --git a/arch/arm/boot/dts/armada-388-gp.dts b/arch/arm/boot/dts/armada-388-gp.dts
> index 4df22bf91683..590b383db323 100644
> --- a/arch/arm/boot/dts/armada-388-gp.dts
> +++ b/arch/arm/boot/dts/armada-388-gp.dts
> @@ -173,6 +173,16 @@
>   				status = "okay";
>   				#address-cells = <1>;
>   				#size-cells = <0>;
> +
> +				sata0: sata-port at 0 {
> +					reg = <0>;
> +					target-supply = <&reg_5v_sata0>;
> +				};
> +
> +				sata1: sata-port at 1 {
> +					reg = <1>;
> +					target-supply = <&reg_5v_sata1>;
> +				};
>   			};
>
>   			sata at e0000 {
> @@ -181,6 +191,16 @@
>   				status = "okay";
>   				#address-cells = <1>;
>   				#size-cells = <0>;
> +
> +				sata2: sata-port at 0 {
> +					reg = <0>;
> +					target-supply = <&reg_5v_sata2>;
> +				};
> +
> +				sata3: sata-port at 1 {
> +					reg = <1>;
> +					target-supply = <&reg_5v_sata3>;
> +				};
>   			};
>
>   			sdhci at d8000 {
> @@ -278,6 +298,112 @@
>   		regulator-always-on;
>   		gpio = <&expander0 4 GPIO_ACTIVE_HIGH>;
>   	};
> +
> +	reg_sata0: pwr-sata0 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "pwr_en_sata0";
> +		enable-active-high;
> +		regulator-always-on;
> +
> +	};
> +
> +	reg_5v_sata0: v5-sata0 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v5.0-sata0";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +		vin-supply = <&reg_sata0>;
> +	};
> +
> +	reg_12v_sata0: v12-sata0 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v12.0-sata0";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		regulator-always-on;
> +		vin-supply = <&reg_sata0>;
> +	};

AFAIK the separate v5 / 12v regulators you're creating here
are not used anywhere. So I guess there just here to
accurately / completely describe the power topology ?

> +
> +	reg_sata1: pwr-sata1 {
> +		regulator-name = "pwr_en_sata1";
> +		compatible = "regulator-fixed";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		enable-active-high;
> +		regulator-always-on;


The always on here seems to a bit weird, wasn't the
whole purpose of this patch set to teach ahci_platform
to turn it on as needed ?

You do probably want to put a regulator-boot-on here so
that disks do not get an unwanted powercycle (bad for
their lifetime) when the firmware has already turned on
the disk. Downside of using regulator-boot-on is that if
the power is not actually turned on no power-on-delay is
done, but we're not using a power on delay anyways.

The same goes for reg_sata2 & reg_sata3.

> +		gpio = <&expander0 3 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	reg_5v_sata1: v5-sata1 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v5.0-sata1";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +		vin-supply = <&reg_sata1>;
> +	};
> +
> +	reg_12v_sata1: v12-sata1 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v12.0-sata1";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		regulator-always-on;
> +		vin-supply = <&reg_sata1>;
> +	};
> +
> +	reg_sata2: pwr-sata2 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "pwr_en_sata2";
> +		enable-active-high;
> +		regulator-always-on;
> +		gpio = <&expander0 11 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	reg_5v_sata2: v5-sata2 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v5.0-sata2";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +		vin-supply = <&reg_sata2>;
> +	};
> +
> +	reg_12v_sata2: v12-sata2 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v12.0-sata2";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		regulator-always-on;
> +		vin-supply = <&reg_sata2>;
> +	};
> +
> +	reg_sata3: pwr-sata3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "pwr_en_sata3";
> +		enable-active-high;
> +		regulator-always-on;
> +		gpio = <&expander0 12 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	reg_5v_sata3: v5-sata3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v5.0-sata3";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +		vin-supply = <&reg_sata3>;
> +	};
> +
> +	reg_12v_sata3: v12-sata3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v12.0-sata3";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		regulator-always-on;
> +		vin-supply = <&reg_sata3>;
> +	};
>   };
>
>   &pinctrl {
>

Regards,

Hans