[PATCH 4/6] i2c: busses: add SLIMpro I2C device driver on APM X-Gene platform

[Feng Kan]

On Tue, Nov 11, 2014 at 1:51 PM, Arnd Bergmann <arnd at arndb.de> wrote:
> On Tuesday 07 October 2014 17:06:47 Feng Kan wrote:
>> diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
>> index 2e45ae3..a03042c 100644
>> --- a/drivers/i2c/busses/Kconfig
>> +++ b/drivers/i2c/busses/Kconfig
>> @@ -1009,6 +1009,15 @@ config I2C_CROS_EC_TUNNEL
>>         connected there. This will work whatever the interface used to
>>         talk to the EC (SPI, I2C or LPC).
>>
>> +config I2C_XGENE_SLIMPRO
>> +     tristate "APM X-Gene SoC I2C SLIMpro devices support"
>> +     depends on ARCH_XGENE && XGENE_SLIMPRO_MBOX
>
> Why this dependency on XGENE_SLIMPRO_MBOX?
>
> Better replace it with a dependency on MAILBOX.
Arnd, just a question. Is this because this possibly help with future
compatibility by choosing a more broad dependency?
>
>> +     } else {
>> +             spin_lock_irqsave(&ctx->lock, flags);
>> +             ctx->i2c_rx_poll = 1;
>> +             for (count = SLIMPRO_I2C_WAIT_COUNT; count > 0; count--) {
>> +                     if (ctx->i2c_rx_poll == 0)
>> +                             break;
>> +                     udelay(100);
>> +             }
>
> No, you can't block the CPU for an extended amount of time with
> interrupts disabled. Please kill this code.
>
>> +     ctx->resp_msg = data;
>> +     if (ctx->mbox_client.tx_block)
>> +             init_completion(&ctx->rd_complete);
>
> reinit_completion()?
>
>> +static int slimpro_i2c_blkrd(struct slimpro_i2c_dev *ctx, u32 chip, u32 addr,
>> +                             u32 addrlen, u32 protocol, u32 readlen,
>> +                             u32 with_data_len, void *data)
>> +{
>> +     dma_addr_t paddr;
>> +     u32 msg[3];
>> +     int rc;
>> +
>> +     paddr = dma_map_single(ctx->dev, ctx->dma_buffer, readlen,
>> +                            DMA_FROM_DEVICE);
>
> ctx->dev is probably the wrong device here. The i2c controller is not
> DMA capable itself, you need to have a pointer to the device that actually
> performs the DMA here.
>
>
>> +     /* Request mailbox channel */
>> +     cl->dev = &pdev->dev;
>> +     cl->rx_callback = slimpro_i2c_rx_cb;
>> +     cl->tx_done = slimpro_i2c_tx_done;
>> +     cl->tx_block = true;
>> +     cl->tx_tout = SLIMPRO_OP_TO_MS;
>> +     cl->knows_txdone = false;
>> +     cl->chan_name = "i2c-slimpro";
>> +     ctx->mbox_chan = mbox_request_channel(cl);
>
> This is not the correct interface.
>
>> +     rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
>> +     if (rc)
>> +             dev_warn(&pdev->dev, "Unable to set dma mask\n");
>
> Are you sure that this is the correct device to perform the DMA?
>
> Moreover, the mask doesn't match the usage: the slimpro_i2c_blkrd
> function passes in only the lower 32 bit of the address, which would
> be DMA_BIT_MASK(32).
>
>> +#ifdef CONFIG_OF
>> +static struct of_device_id xgene_slimpro_i2c_id[] = {
>> +     {.compatible = "apm,xgene-slimpro-i2c" },
>> +     {},
>> +};
>> +MODULE_DEVICE_TABLE(of, xgene_slimpro_i2c_dt_ids);
>> +#endif
>> +
>> +static struct platform_driver xgene_slimpro_i2c_driver = {
>> +     .probe  = xgene_slimpro_i2c_probe,
>> +     .remove = xgene_slimpro_i2c_remove,
>> +     .driver = {
>> +             .name   = XGENE_SLIMPRO_I2C,
>> +             .owner  = THIS_MODULE,
>> +             .of_match_table = of_match_ptr(xgene_slimpro_i2c_id)
>> +     },
>> +};
>
> The driver only supports DT, so just drop the #ifdef and the of_match_ptr().
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-i2c" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html