[PATCH] mvebu: add Linksys WRT1900AC (Mamba) support
Gregory CLEMENT
gregory.clement at free-electrons.com
Fri Jan 9 04:46:27 PST 2015
Hi Imre,
On 09/01/2015 13:31, Imre Kaloz wrote:
> The Linksys WRT1900AC (Mamba) is a router that has
>
> - 2 mini-PCIe slots with Marvell 88W8864 radios
> - 1 USB 3.0 port
> - 1 USB 2.0/eSATAp port
> - 2 Ethernet interfaces connected to a 88E6172 switch (1x WAN + 4x LAN)
> - 128MB NAND flash
> - 256MB RAM
Thanks for your contribution
>
> Signed-off-by: Imre Kaloz <kaloz at openwrt.org>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/armada-xp-mamba.dts | 264 ++++++++++++++++++++++++++++++++++
> 2 files changed, 265 insertions(+)
> create mode 100644 arch/arm/boot/dts/armada-xp-mamba.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 91bd5bd..2914c88 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -542,6 +542,7 @@ dtb-$(CONFIG_MACH_ARMADA_XP) += \
> armada-xp-gp.dtb \
> armada-xp-lenovo-ix4-300d.dtb \
> armada-xp-matrix.dtb \
> + armada-xp-mamba.dtb \
> armada-xp-netgear-rn2120.dtb \
> armada-xp-openblocks-ax3-4.dtb \
> armada-xp-synology-ds414.dtb
> diff --git a/arch/arm/boot/dts/armada-xp-mamba.dts b/arch/arm/boot/dts/armada-xp-mamba.dts
> new file mode 100644
> index 0000000..1f13e49
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-xp-mamba.dts
> @@ -0,0 +1,264 @@
> +/*
> + * Device Tree file for the Linksys WRT1900AC (Mamba).
> + *
> + * Note: this board is shipped with a new generation boot loader that
> + * remaps internal registers at 0xf1000000. Therefore, if earlyprintk
> + * is used, the CONFIG_DEBUG_MVEBU_UART_ALTERNATE option should be
> + * used.
> + *
> + * Copyright (C) 2014 Imre Kaloz <kaloz at openwrt.org>
> + *
> + * Based on armada-xp-axpwifiap.dts:
> + *
> + * Copyright (C) 2013 Marvell
> + *
> + * Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
We are moving to a dual license GPL/X11:
http://thread.gmane.org/gmane.linux.ports.arm.kernel/380065
Could you consider to use it too?
The file you based on will be converted, all the author of this
file already have given their acked-by.
In meantime, I will review the content of your patch.
Thanks,
Gregory
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include "armada-xp-mv78230.dtsi"
> +
> +/ {
> + model = "Linksys WRT1900AC (Mamba)";
> + compatible = "linksys,mamba", "marvell,armadaxp-mv78230", "marvell,armadaxp", "marvell,armada-370-xp";
> +
> + chosen {
> + bootargs = "console=ttyS0,115200";
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x00000000 0x00000000 0x10000000>; /* 256MB */
> + };
> +
> + soc {
> + ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
> + MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>;
> +
> + pcie-controller {
> + status = "okay";
> +
> + /* Etron EJ168 USB 3.0 controller */
> + pcie at 1,0 {
> + /* Port 0, Lane 0 */
> + status = "okay";
> + };
> +
> + /* First mini-PCIe port */
> + pcie at 2,0 {
> + /* Port 0, Lane 1 */
> + status = "okay";
> + };
> +
> + /* Second mini-PCIe port */
> + pcie at 3,0 {
> + /* Port 0, Lane 3 */
> + status = "okay";
> + };
> + };
> +
> + internal-regs {
> + pinctrl {
> + pmx_ge0: pmx-ge0 {
> + marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3",
> + "mpp4", "mpp5", "mpp6", "mpp7",
> + "mpp8", "mpp9", "mpp10", "mpp11";
> + marvell,function = "ge0";
> + };
> +
> + pmx_ge1: pmx-ge1 {
> + marvell,pins = "mpp12", "mpp13", "mpp14", "mpp15",
> + "mpp16", "mpp17", "mpp18", "mpp19",
> + "mpp20", "mpp21", "mpp22", "mpp23";
> + marvell,function = "ge1";
> + };
> +
> + pmx_keys: pmx-keys {
> + marvell,pins = "mpp32", "mpp33";
> + marvell,function = "gpio";
> + };
> +
> + pmx_spi: pmx-spi {
> + marvell,pins = "mpp36", "mpp37", "mpp38", "mpp39";
> + marvell,function = "spi";
> + };
> +
> + power_led_pin: power-led-pin {
> + marvell,pins = "mpp40";
> + marvell,function = "gpio";
> + };
> +
> + gpio_fan_pin: gpio-fan-pin {
> + marvell,pins = "mpp24";
> + marvell,function = "gpio";
> + };
> + };
> +
> + serial at 12000 {
> + clock-frequency = <250000000>;
> + status = "okay";
> + };
> +
> + sata at a0000 {
> + nr-ports = <1>;
> + status = "okay";
> + };
> +
> + ethernet at 70000 {
> + pinctrl-0 = <&pmx_ge0>;
> + pinctrl-names = "default";
> + status = "okay";
> + phy-mode = "rgmii-id";
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + ethernet at 74000 {
> + pinctrl-0 = <&pmx_ge1>;
> + pinctrl-names = "default";
> + status = "okay";
> + phy-mode = "rgmii-id";
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + /* USB part of the eSATA/USB 2.0 port */
> + usb at 50000 {
> + status = "okay";
> + };
> +
> + i2c at 11000 {
> + status = "okay";
> + clock-frequency = <100000>;
> +
> + tmp421 at 4c {
> + compatible = "ti,tmp421";
> + reg = <0x4c>;
> + };
> + };
> +
> + nand at d0000 {
> + status = "okay";
> + num-cs = <1>;
> + marvell,nand-keep-config;
> + marvell,nand-enable-arbiter;
> + nand-on-flash-bbt;
> + nand-ecc-strength = <4>;
> + nand-ecc-step-size = <512>;
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x0000000 0x100000>; /* 1MB */
> + read-only;
> + };
> +
> + partition at 100000 {
> + label = "u_env";
> + reg = <0x100000 0x40000>; /* 256KB */
> + };
> +
> + partition at 140000 {
> + label = "s_env";
> + reg = <0x140000 0x40000>; /* 256KB */
> + };
> +
> + partition at 900000 {
> + label = "devinfo";
> + reg = <0x900000 0x100000>; /* 1MB */
> + read-only;
> + };
> +
> + partition at a00000 {
> + label = "kernel1";
> + reg = <0xa00000 0x2800000>; /* 3MB + rootfs1 */
> + };
> +
> + partition at d00000 {
> + label = "rootfs1";
> + reg = <0xd00000 0x2500000>; /* 37MB */
> + };
> +
> + partition at 3200000 {
> + label = "kernel2";
> + reg = <0x3200000 0x2800000>; /* 3MB + rootfs2 */
> + };
> +
> + partition at 3500000 {
> + label = "rootfs2";
> + reg = <0x3500000 0x2500000>; /* 37MB */
> + };
> +
> + /* Last MB is for the BBT, i.e. not writable */
> + partition at 5a00000 {
> + label = "syscfg";
> + reg = <0x5a00000 0x2600000>; /* 38MB */
> + };
> + };
> +
> + spi0: spi at 10600 {
> + status = "okay";
> + pinctrl-0 = <&pmx_spi>;
> + pinctrl-names = "default";
> +
> + spi-flash at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "mr25h256";
> + reg = <0>; /* Chip select 0 */
> + spi-max-frequency = <108000000>;
> + };
> + };
> + };
> + };
> +
> + gpio_keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_keys>;
> + pinctrl-names = "default";
> +
> + button at 1 {
> + label = "WPS";
> + linux,code = <KEY_WPS_BUTTON>;
> + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
> + };
> +
> + button at 2 {
> + label = "Factory Reset Button";
> + linux,code = <KEY_RESTART>;
> + gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&power_led_pin>;
> + pinctrl-names = "default";
> +
> + power {
> + label = "mamba:white:power";
> + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
> + default-state = "on";
> + };
> + };
> +
> + gpio_fan {
> + /* SUNON HA4010V4-0000-C99 */
> + compatible = "gpio-fan";
> + gpios = <&gpio0 24 0>;
> +
> + gpio-fan,speed-map = <0 0
> + 4500 1>;
> + };
> +};
>
--
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com
More information about the linux-arm-kernel
mailing list