[PATCH v3 4/4] mmc: sdhci: host: add new f_sdh30

Vincent Yang vincent.yang.fujitsu at gmail.com
Fri Jan 9 03:41:45 PST 2015


This patch adds new host controller driver for
Fujitsu SDHCI controller f_sdh30.

Signed-off-by: Andy Green <andy.green at linaro.org>
Signed-off-by: Vincent Yang <Vincent.Yang at tw.fujitsu.com>
Signed-off-by: Tetsuya Takinishi <t.takinishi at jp.fujitsu.com>
---
 .../devicetree/bindings/mmc/sdhci-fujitsu.txt      |  30 ++
 drivers/mmc/host/Kconfig                           |   8 +
 drivers/mmc/host/Makefile                          |   1 +
 drivers/mmc/host/sdhci_f_sdh30.c                   | 306 +++++++++++++++++++++
 4 files changed, 345 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt
 create mode 100644 drivers/mmc/host/sdhci_f_sdh30.c

diff --git a/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt
new file mode 100644
index 0000000..d77df7b
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt
@@ -0,0 +1,30 @@
+* Fujitsu SDHCI controller
+
+This file documents differences between the core properties in mmc.txt
+and the properties used by the sdhci_f_sdh30 driver.
+
+Required properties:
+- compatible: "fujitsu,mb86s70-sdhci-3.0"
+
+Optional properties:
+- vqmmc-supply: phandle to the regulator device tree node, mentioned
+  as the VCCQ/VDD_IO supply in the eMMC/SD specs.
+- clocks: Must contain an entry for each entry in clock-names. It is a
+  list of phandles and clock-specifier pairs.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names: Should contain the following two entries:
+	"iface" - clock used for sdhci interface
+	"core"  - core clock for sdhci controller
+
+Example:
+
+	sdhci1: mmc at 36600000 {
+		compatible = "fujitsu,mb86s70-sdhci-3.0";
+		reg = <0 0x36600000 0x1000>;
+		interrupts = <0 172 0x4>,
+			     <0 173 0x4>;
+		bus-width = <4>;
+		vqmmc-supply = <&vccq_sdhci1>;
+		clocks = <&clock 2 2 0>, <&clock 2 3 0>;
+		clock-names = "iface", "core";
+	};
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index 2d6fbdd..288dcc3 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -290,6 +290,14 @@ config MMC_SDHCI_BCM2835
 	  This selects the BCM2835 SD/MMC controller. If you have a BCM2835
 	  platform with SD or MMC devices, say Y or M here.
 
+config MMC_SDHCI_F_SDH30
+	tristate "SDHCI support for Fujitsu Semiconductor F_SDH30"
+	depends on MMC_SDHCI_PLTFM
+	depends on OF
+	help
+	  This selects the Secure Digital Host Controller Interface (SDHCI)
+	  Needed by some Fujitsu SoC for MMC / SD / SDIO support.
+	  If you have a controller with this interface, say Y or M here.
 	  If unsure, say N.
 
 config MMC_MOXART
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index f7b0a77..6a7cfe0 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_MMC_SDHCI_PXAV3)	+= sdhci-pxav3.o
 obj-$(CONFIG_MMC_SDHCI_PXAV2)	+= sdhci-pxav2.o
 obj-$(CONFIG_MMC_SDHCI_S3C)	+= sdhci-s3c.o
 obj-$(CONFIG_MMC_SDHCI_SIRF)   	+= sdhci-sirf.o
+obj-$(CONFIG_MMC_SDHCI_F_SDH30)	+= sdhci_f_sdh30.o
 obj-$(CONFIG_MMC_SDHCI_SPEAR)	+= sdhci-spear.o
 obj-$(CONFIG_MMC_WBSD)		+= wbsd.o
 obj-$(CONFIG_MMC_AU1X)		+= au1xmmc.o
diff --git a/drivers/mmc/host/sdhci_f_sdh30.c b/drivers/mmc/host/sdhci_f_sdh30.c
new file mode 100644
index 0000000..2dc16e7
--- /dev/null
+++ b/drivers/mmc/host/sdhci_f_sdh30.c
@@ -0,0 +1,306 @@
+/*
+ * linux/drivers/mmc/host/sdhci_f_sdh30.c
+ *
+ * Copyright (C) 2013 - 2015 Fujitsu Semiconductor, Ltd
+ *              Vincent Yang <vincent.yang at tw.fujitsu.com>
+ * Copyright (C) 2015 Linaro Ltd  Andy Green <andy.green at linaro.org>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, version 2 of the License.
+ */
+
+#include <linux/err.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/mmc/sd.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/card.h>
+#include <linux/gpio.h>
+#include <linux/of_gpio.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/pm_runtime.h>
+#include <linux/suspend.h>
+
+#include "sdhci.h"
+#include "sdhci-pltfm.h"
+
+/* F_SDH30 extended Controller registers */
+#define F_SDH30_AHB_CONFIG		0x100
+#define  F_SDH30_AHB_BIGED		0x00000040
+#define  F_SDH30_BUSLOCK_DMA		0x00000020
+#define  F_SDH30_BUSLOCK_EN		0x00000010
+#define  F_SDH30_SIN			0x00000008
+#define  F_SDH30_AHB_INCR_16		0x00000004
+#define  F_SDH30_AHB_INCR_8		0x00000002
+#define  F_SDH30_AHB_INCR_4		0x00000001
+
+#define F_SDH30_TUNING_SETTING		0x108
+#define  F_SDH30_CMD_CHK_DIS		0x00010000
+
+#define F_SDH30_IO_CONTROL2		0x114
+#define  F_SDH30_CRES_O_DN		0x00080000
+#define  F_SDH30_MSEL_O_1_8		0x00040000
+
+#define F_SDH30_ESD_CONTROL		0x124
+#define  F_SDH30_EMMC_RST		0x00000002
+#define  F_SDH30_EMMC_HS200		0x01000000
+
+#define F_SDH30_CMD_DAT_DELAY		0x200
+
+#define F_SDH30_MIN_CLOCK		400000
+
+struct f_sdhost_priv {
+	struct clk *clk_iface;
+	struct clk *clk;
+	u32 vendor_hs200;
+	struct device *dev;
+};
+
+void sdhci_f_sdh30_soft_voltage_switch(struct sdhci_host *host)
+{
+	struct f_sdhost_priv *priv = sdhci_priv(host);
+	u32 ctrl = 0;
+
+	usleep_range(2500, 3000);
+	ctrl = sdhci_readl(host, F_SDH30_IO_CONTROL2);
+	ctrl |= F_SDH30_CRES_O_DN;
+	sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2);
+	ctrl |= F_SDH30_MSEL_O_1_8;
+	sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2);
+
+	ctrl &= ~F_SDH30_CRES_O_DN;
+	sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2);
+	usleep_range(2500, 3000);
+
+	if (priv->vendor_hs200) {
+		dev_info(priv->dev, "%s: setting hs200\n", __func__);
+		ctrl = sdhci_readl(host, F_SDH30_ESD_CONTROL);
+		ctrl |= priv->vendor_hs200;
+		sdhci_writel(host, ctrl, F_SDH30_ESD_CONTROL);
+	}
+
+	ctrl = sdhci_readl(host, F_SDH30_TUNING_SETTING);
+	ctrl |= F_SDH30_CMD_CHK_DIS;
+	sdhci_writel(host, ctrl, F_SDH30_TUNING_SETTING);
+}
+
+unsigned int sdhci_f_sdh30_get_min_clock(struct sdhci_host *host)
+{
+	return F_SDH30_MIN_CLOCK;
+}
+
+void sdhci_f_sdh30_reset(struct sdhci_host *host, u8 mask)
+{
+	if (sdhci_readw(host, SDHCI_CLOCK_CONTROL) == 0)
+		sdhci_writew(host, 0xBC01, SDHCI_CLOCK_CONTROL);
+
+	sdhci_reset(host, mask);
+}
+
+static const struct sdhci_ops sdhci_f_sdh30_ops = {
+	.voltage_switch = sdhci_f_sdh30_soft_voltage_switch,
+	.get_min_clock = sdhci_f_sdh30_get_min_clock,
+	.reset = sdhci_f_sdh30_reset,
+	.set_clock = sdhci_set_clock,
+	.set_bus_width = sdhci_set_bus_width,
+	.set_uhs_signaling = sdhci_set_uhs_signaling,
+};
+
+static int sdhci_f_sdh30_probe(struct platform_device *pdev)
+{
+	struct sdhci_host *host;
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	int irq, ctrl = 0, ret = 0;
+	struct f_sdhost_priv *priv;
+	u32 reg = 0;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(dev, "%s: no irq specified\n", __func__);
+		ret = irq;
+		goto err;
+	}
+
+	host = sdhci_alloc_host(dev, sizeof(struct sdhci_host) +
+						sizeof(struct f_sdhost_priv));
+	if (IS_ERR(host)) {
+		ret = -ENOMEM;
+		goto err;
+	}
+	priv = sdhci_priv(host);
+	priv->dev = dev;
+
+	host->quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC |
+		       SDHCI_QUIRK_INVERTED_WRITE_PROTECT;
+	host->quirks2 = SDHCI_QUIRK2_SUPPORT_SINGLE |
+			SDHCI_QUIRK2_TUNING_WORK_AROUND;
+
+	ret = mmc_of_parse(host->mmc);
+	if (ret)
+		goto err_of_parse;
+
+	platform_set_drvdata(pdev, host);
+
+	sdhci_get_of_property(pdev);
+	host->hw_name = "f_sdh30";
+	host->ops = &sdhci_f_sdh30_ops;
+	host->irq = irq;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	host->ioaddr = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(host->ioaddr)) {
+		dev_err(dev, "%s: failed to remap registers\n", __func__);
+		ret = -ENXIO;
+		goto err_of_parse;
+	}
+
+	priv->clk_iface = devm_clk_get(&pdev->dev, "iface");
+	if (!IS_ERR(priv->clk_iface)) {
+		ret = clk_prepare_enable(priv->clk_iface);
+		if (ret < 0) {
+			dev_err(dev, "Failed to enable iface clock: %d\n", ret);
+			goto err_of_parse;
+		}
+	}
+	priv->clk = devm_clk_get(&pdev->dev, "core");
+	if (!IS_ERR(priv->clk)) {
+		ret = clk_prepare_enable(priv->clk);
+		if (ret < 0) {
+			dev_err(dev, "Failed to enable core clock: %d\n", ret);
+			goto err_clk;
+		}
+	}
+
+	pm_runtime_set_active(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+	ret = pm_runtime_get_sync(&pdev->dev);
+	if (ret < 0)
+		dev_err(dev, "Failed to pm_runtime_get_sync: %d\n", ret);
+
+	/* init vendor specific regs */
+	ctrl = sdhci_readw(host, F_SDH30_AHB_CONFIG);
+	ctrl |= F_SDH30_SIN | F_SDH30_AHB_INCR_16 | F_SDH30_AHB_INCR_8 |
+		F_SDH30_AHB_INCR_4;
+	ctrl &= ~(F_SDH30_AHB_BIGED | F_SDH30_BUSLOCK_EN);
+	sdhci_writew(host, ctrl, F_SDH30_AHB_CONFIG);
+
+	reg = sdhci_readl(host, F_SDH30_ESD_CONTROL);
+	sdhci_writel(host, reg & ~F_SDH30_EMMC_RST, F_SDH30_ESD_CONTROL);
+	msleep(20);
+	sdhci_writel(host, reg | F_SDH30_EMMC_RST, F_SDH30_ESD_CONTROL);
+
+	reg = sdhci_readl(host, SDHCI_CAPABILITIES);
+	if (reg & SDHCI_CAN_DO_8BIT)
+		priv->vendor_hs200 = F_SDH30_EMMC_HS200;
+	else
+		priv->vendor_hs200 = 0;
+
+	ret = sdhci_add_host(host);
+	if (ret) {
+		dev_err(dev, "%s: host add error\n", __func__);
+		goto err_add_host;
+	}
+
+	return 0;
+
+err_add_host:
+	pm_runtime_disable(&pdev->dev);
+	pm_runtime_put_noidle(&pdev->dev);
+	clk_disable_unprepare(priv->clk);
+err_clk:
+	clk_disable_unprepare(priv->clk_iface);
+err_of_parse:
+	sdhci_free_host(host);
+err:
+	return ret;
+}
+
+static int sdhci_f_sdh30_remove(struct platform_device *pdev)
+{
+	struct sdhci_host *host = platform_get_drvdata(pdev);
+	struct f_sdhost_priv *priv = sdhci_priv(host);
+	struct resource *iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+	pm_runtime_get_sync(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+	pm_runtime_put_noidle(&pdev->dev);
+
+	sdhci_remove_host(host, readl(host->ioaddr + SDHCI_INT_STATUS) ==
+			  0xffffffff);
+	release_mem_region(iomem->start, resource_size(iomem));
+
+	clk_disable_unprepare(priv->clk_iface);
+	clk_disable_unprepare(priv->clk);
+
+	sdhci_free_host(host);
+	platform_set_drvdata(pdev, NULL);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int sdhci_f_sdh30_suspend(struct device *dev)
+{
+	struct sdhci_host *host = dev_get_drvdata(dev);
+
+	return sdhci_suspend_host(host);
+}
+
+static int sdhci_f_sdh30_resume(struct device *dev)
+{
+	struct sdhci_host *host = dev_get_drvdata(dev);
+
+	return sdhci_resume_host(host);
+}
+#endif
+
+#ifdef CONFIG_PM
+static int sdhci_f_sdh30_runtime_suspend(struct device *dev)
+{
+	struct sdhci_host *host = dev_get_drvdata(dev);
+
+	return sdhci_runtime_suspend_host(host);
+}
+
+static int sdhci_f_sdh30_runtime_resume(struct device *dev)
+{
+	struct sdhci_host *host = dev_get_drvdata(dev);
+
+	return sdhci_runtime_resume_host(host);
+}
+#endif
+
+static const struct dev_pm_ops sdhci_f_sdh30_pmops = {
+	SET_SYSTEM_SLEEP_PM_OPS(sdhci_f_sdh30_suspend, sdhci_f_sdh30_resume)
+	SET_RUNTIME_PM_OPS(sdhci_f_sdh30_runtime_suspend,
+			   sdhci_f_sdh30_runtime_resume, NULL)
+};
+
+static const struct of_device_id f_sdh30_dt_ids[] = {
+	{ .compatible = "fujitsu,mb86s70-sdhci-3.0" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, f_sdh30_dt_ids);
+
+static struct platform_driver sdhci_f_sdh30_driver = {
+	.driver = {
+		.name = "f_sdh30",
+		.of_match_table = f_sdh30_dt_ids,
+#ifdef CONFIG_PM_SLEEP
+		.pm	= &sdhci_f_sdh30_pmops,
+#endif
+	},
+	.probe	= sdhci_f_sdh30_probe,
+	.remove	= sdhci_f_sdh30_remove,
+};
+
+module_platform_driver(sdhci_f_sdh30_driver);
+
+MODULE_DESCRIPTION("F_SDH30 SD Card Controller driver");
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("FUJITSU SEMICONDUCTOR LTD.");
+MODULE_ALIAS("platform:f_sdh30");
-- 
1.9.0




More information about the linux-arm-kernel mailing list