[PATCH v5] mmc: dw_mmc: add quirk for broken data transfer over scheme
Jaehoon Chung
jh80.chung at samsung.com
Wed Jan 7 17:58:07 PST 2015
Hi, Addy.
On 01/05/2015 05:21 PM, Addy Ke wrote:
> This patch add a new quirk to add a s/w timer to notify the driver
> to terminate current transfer and report a data timeout to the core,
> if DTO interrupt does NOT come within the given time.
>
> dw_mmc call mmc_request_done func to finish transfer depends on
> DTO interrupt. If DTO interrupt does not come in sending data state,
> the current transfer will be blocked.
>
> We got the reply from synopsys:
> There are two counters but both use the same value of [31:8] bits.
> Data timeout counter doesn't wait for stop clock and you should get
> DRTO even when the clock is not stopped.
> Host Starvation timeout counter is triggered with stop clock condition.
>
> This means that host should get DRTO and DTO interrupt.
>
> But this case really exists, when driver reads tuning data from
> card on RK3288-pink2 board. I measured waveforms by oscilloscope
> and found that card clock was always on and data lines were always
> holded high level in sending data state.
>
> There are two possibility that data over interrupt doesn't come in
> reading data state on RK3X SoCs:
> - get command done interrupt, but doesn't get any data-related interrupt.
> - get data error interrupt, but doesn't get data over interrupt.
>
> We don't know why we have this problem, but we need it to fix this problem now.
> And I will post a follow up change when we find the root cause.
>
> Signed-off-by: Addy Ke <addy.ke at rock-chips.com>
> ---
> Changes in v2:
> - fix some typo.
> - remove extra timeout value (250ms).
> - remove dw_mci_dto_start_monitor func.
> - use "broken-dto" for new quirk and change Subject for it.
>
> Changes in v3:
> - Remove dts for broken-dto, just add this quirk in dw_mci_rockchip_init
>
> Changes in v4:
> - fix bug that may cause 32 bit overflow by (drto_clks * 1000).
> - doesn't call mod_timer in writing data state, becase TMOUT register only
> for reading data.
>
> Changes in v5:
> - fix some typo.
> - add a buffer for drto_ms.
> - move drto_ms related code to a helper function.
>
> drivers/mmc/host/dw_mmc-rockchip.c | 3 ++
> drivers/mmc/host/dw_mmc.c | 71 ++++++++++++++++++++++++++++++++++++--
> include/linux/mmc/dw_mmc.h | 5 +++
> 3 files changed, 77 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/mmc/host/dw_mmc-rockchip.c b/drivers/mmc/host/dw_mmc-rockchip.c
> index 5650ac4..ba92ebd 100644
> --- a/drivers/mmc/host/dw_mmc-rockchip.c
> +++ b/drivers/mmc/host/dw_mmc-rockchip.c
> @@ -73,6 +73,9 @@ static int dw_mci_rockchip_init(struct dw_mci *host)
> /* It is slot 8 on Rockchip SoCs */
> host->sdio_id0 = 8;
>
> + /* It needs this quirk on all Rockchip SoCs */
> + host->pdata->quirks |= DW_MCI_QUIRK_BROKEN_DTO;
> +
> return 0;
> }
>
> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
> index 6e4d864..ace4b40 100644
> --- a/drivers/mmc/host/dw_mmc.c
> +++ b/drivers/mmc/host/dw_mmc.c
> @@ -1468,6 +1468,20 @@ static int dw_mci_data_complete(struct dw_mci *host, struct mmc_data *data)
> return data->error;
> }
>
> +static unsigned int dw_mci_get_drto_ms(struct dw_mci *host)
> +{
> + unsigned int drto_clks;
> + unsigned int drto_ms;
> +
> + drto_clks = mci_readl(host, TMOUT) >> 8;
> + drto_ms = DIV_ROUND_UP(drto_clks, host->bus_hz / 1000);
> +
> + /* add a buffer */
> + drto_ms += 10;
Add a buffer? What means?
> +
> + return drto_ms;
> +}
dw_mci_set_drto() instead of dw_mci_get_drto_ms().
Then you can include the codes relevant to broken-dto.
static unsigned int (or void) dw_mci_set_drto(struct dw_mci *host) {
if (!(host->quirks & DW_MCI_QUIRK_BROKEN_DTO))
return;
...
add codes relevant to broken-dtop (mod_timer) at here.
}
If you need to start timer, you have only to call dw_mci_set_drto().
how about?
Best Regards,
Jaehoon Chung
> +
> static void dw_mci_tasklet_func(unsigned long priv)
> {
> struct dw_mci *host = (struct dw_mci *)priv;
> @@ -1477,6 +1491,7 @@ static void dw_mci_tasklet_func(unsigned long priv)
> enum dw_mci_state state;
> enum dw_mci_state prev_state;
> unsigned int err;
> + unsigned int drto_ms;
>
> spin_lock(&host->lock);
>
> @@ -1542,8 +1557,19 @@ static void dw_mci_tasklet_func(unsigned long priv)
> }
>
> if (!test_and_clear_bit(EVENT_XFER_COMPLETE,
> - &host->pending_events))
> + &host->pending_events)) {
> + /*
> + * If all data-related interrupts don't come
> + * within the given time in reading data state.
> + */
> + if ((host->quirks & DW_MCI_QUIRK_BROKEN_DTO) &&
> + (host->dir_status == DW_MCI_RECV_STATUS)) {
> + drto_ms = dw_mci_get_drto_ms(host);
> + mod_timer(&host->dto_timer, jiffies +
> + msecs_to_jiffies(drto_ms));
> + }
> break;
> + }
>
> set_bit(EVENT_XFER_COMPLETE, &host->completed_events);
>
> @@ -1573,8 +1599,20 @@ static void dw_mci_tasklet_func(unsigned long priv)
>
> case STATE_DATA_BUSY:
> if (!test_and_clear_bit(EVENT_DATA_COMPLETE,
> - &host->pending_events))
> + &host->pending_events)) {
> + /*
> + * If data error interrupt comes but data over
> + * interrupt doesn't come within the given time.
> + * in reading data state.
> + */
> + if ((host->quirks & DW_MCI_QUIRK_BROKEN_DTO) &&
> + (host->dir_status == DW_MCI_RECV_STATUS)) {
> + drto_ms = dw_mci_get_drto_ms(host);
> + mod_timer(&host->dto_timer, jiffies +
> + msecs_to_jiffies(drto_ms));
> + }
> break;
> + }
>
> host->data = NULL;
> set_bit(EVENT_DATA_COMPLETE, &host->completed_events);
> @@ -2135,6 +2173,9 @@ static irqreturn_t dw_mci_interrupt(int irq, void *dev_id)
> }
>
> if (pending & SDMMC_INT_DATA_OVER) {
> + if (host->quirks & DW_MCI_QUIRK_BROKEN_DTO)
> + del_timer(&host->dto_timer);
> +
> mci_writel(host, RINTSTS, SDMMC_INT_DATA_OVER);
> if (!host->data_status)
> host->data_status = pending;
> @@ -2522,6 +2563,28 @@ ciu_out:
> return ret;
> }
>
> +static void dw_mci_dto_timer(unsigned long arg)
> +{
> + struct dw_mci *host = (struct dw_mci *)arg;
> +
> + switch (host->state) {
> + case STATE_SENDING_DATA:
> + case STATE_DATA_BUSY:
> + /*
> + * If DTO interrupt does NOT come in sending data state,
> + * we should notify the driver to terminate current transfer
> + * and report a data timeout to the core.
> + */
> + host->data_status = SDMMC_INT_DRTO;
> + set_bit(EVENT_DATA_ERROR, &host->pending_events);
> + set_bit(EVENT_DATA_COMPLETE, &host->pending_events);
> + tasklet_schedule(&host->tasklet);
> + break;
> + default:
> + break;
> + }
> +}
> +
> #ifdef CONFIG_OF
> static struct dw_mci_of_quirks {
> char *quirk;
> @@ -2670,6 +2733,10 @@ int dw_mci_probe(struct dw_mci *host)
>
> host->quirks = host->pdata->quirks;
>
> + if (host->quirks & DW_MCI_QUIRK_BROKEN_DTO)
> + setup_timer(&host->dto_timer,
> + dw_mci_dto_timer, (unsigned long)host);
> +
> spin_lock_init(&host->lock);
> spin_lock_init(&host->irq_lock);
> INIT_LIST_HEAD(&host->queue);
> diff --git a/include/linux/mmc/dw_mmc.h b/include/linux/mmc/dw_mmc.h
> index 471fb31..2ece0dd 100644
> --- a/include/linux/mmc/dw_mmc.h
> +++ b/include/linux/mmc/dw_mmc.h
> @@ -98,6 +98,7 @@ struct mmc_data;
> * @irq_flags: The flags to be passed to request_irq.
> * @irq: The irq value to be passed to request_irq.
> * @sdio_id0: Number of slot0 in the SDIO interrupt registers.
> + * @dto_timer: Timer for broken data transfer over scheme.
> *
> * Locking
> * =======
> @@ -202,6 +203,8 @@ struct dw_mci {
> int irq;
>
> int sdio_id0;
> +
> + struct timer_list dto_timer;
> };
>
> /* DMA ops for Internal/External DMAC interface */
> @@ -226,6 +229,8 @@ struct dw_mci_dma_ops {
> #define DW_MCI_QUIRK_BROKEN_CARD_DETECTION BIT(3)
> /* No write protect */
> #define DW_MCI_QUIRK_NO_WRITE_PROTECT BIT(4)
> +/* Timer for broken data transfer over scheme */
> +#define DW_MCI_QUIRK_BROKEN_DTO BIT(5)
>
> /* Slot level quirks */
> /* This slot has no write protect */
>
More information about the linux-arm-kernel
mailing list