[PATCH 2/3] ARM: dts: sun7i: Add dts file for Bananapro board
Hans de Goede
hdegoede at redhat.com
Wed Jan 7 12:16:14 PST 2015
Add support for the new Bananapro A20 development board from lemaker.org.
This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for
OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver,
3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi.
Signed-off-by: Hans de Goede <hdegoede at redhat.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/sun7i-a20-bananapro.dts | 261 ++++++++++++++++++++++++++++++
2 files changed, 262 insertions(+)
create mode 100644 arch/arm/boot/dts/sun7i-a20-bananapro.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 548520f..4142831 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -467,6 +467,7 @@ dtb-$(CONFIG_MACH_SUN6I) += \
sun6i-a31s-cs908.dtb
dtb-$(CONFIG_MACH_SUN7I) += \
sun7i-a20-bananapi.dtb \
+ sun7i-a20-bananapro.dtb \
sun7i-a20-cubieboard2.dtb \
sun7i-a20-cubietruck.dtb \
sun7i-a20-hummingbird.dtb \
diff --git a/arch/arm/boot/dts/sun7i-a20-bananapro.dts b/arch/arm/boot/dts/sun7i-a20-bananapro.dts
new file mode 100644
index 0000000..3b4764d
--- /dev/null
+++ b/arch/arm/boot/dts/sun7i-a20-bananapro.dts
@@ -0,0 +1,261 @@
+/*
+ * Copyright 2015 Hans de Goede <hdegoede at redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+/include/ "sun7i-a20.dtsi"
+/include/ "sunxi-common-regulators.dtsi"
+
+/ {
+ model = "LeMaker Banana Pro";
+ compatible = "lemaker,bananapro", "allwinner,sun7i-a20";
+
+ soc at 01c00000 {
+ spi0: spi at 01c05000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins_a>;
+ status = "okay";
+ };
+
+ mmc0: mmc at 01c0f000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 10 0>; /* PH10 */
+ cd-inverted;
+ status = "okay";
+ };
+
+ mmc3: mmc at 01c12000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins_a>;
+ vmmc-supply = <®_vmmc3>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+ };
+
+ usbphy: phy at 01c13400 {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+ };
+
+ ehci0: usb at 01c14000 {
+ status = "okay";
+ };
+
+ ohci0: usb at 01c14400 {
+ status = "okay";
+ };
+
+ ahci: sata at 01c18000 {
+ status = "okay";
+ };
+
+ ehci1: usb at 01c1c000 {
+ status = "okay";
+ };
+
+ ohci1: usb at 01c1c400 {
+ status = "okay";
+ };
+
+ pinctrl at 01c20800 {
+ usb1_vbus_pin_bananapro: usb1_vbus_pin at 0 {
+ allwinner,pins = "PH0";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <0>;
+ allwinner,pull = <0>;
+ };
+
+ usb2_vbus_pin_bananapro: usb2_vbus_pin at 0 {
+ allwinner,pins = "PH1";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <0>;
+ allwinner,pull = <0>;
+ };
+
+ mmc0_cd_pin_bananapi: mmc0_cd_pin at 0 {
+ allwinner,pins = "PH10";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <0>;
+ allwinner,pull = <1>;
+ };
+
+ vmmc3_pin_bananapro: vmmc3_pin at 0 {
+ allwinner,pins = "PH22";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <0>;
+ allwinner,pull = <0>;
+ };
+
+ gmac_power_pin_bananapi: gmac_power_pin at 0 {
+ allwinner,pins = "PH23";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <0>;
+ allwinner,pull = <0>;
+ };
+
+ led_pins_bananapi: led_pins at 0 {
+ allwinner,pins = "PH24", "PG2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <0>;
+ allwinner,pull = <0>;
+ };
+ };
+
+ ir0: ir at 01c21800 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+ };
+
+ uart0: serial at 01c28000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+ };
+
+ uart2: serial at 01c28800 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins_a>;
+ status = "okay";
+ };
+
+ uart7: serial at 01c29c00 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart7_pins_a>;
+ status = "okay";
+ };
+
+ i2c0: i2c at 01c2ac00 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic at 34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 8>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+ };
+
+ i2c2: i2c at 01c2b400 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+ };
+
+ gmac: ethernet at 01c50000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ phy-supply = <®_gmac_3v3>;
+ status = "okay";
+
+ phy1: ethernet-phy at 1 {
+ reg = <1>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_bananapi>;
+
+ green {
+ label = "bananapi:green:usr";
+ gpios = <&pio 7 24 0>;
+ };
+ blue {
+ label = "bananapi:blue:usr";
+ gpios = <&pio 6 2 0>;
+ };
+ };
+
+ reg_usb1_vbus: usb1-vbus {
+ pinctrl-0 = <&usb1_vbus_pin_bananapro>;
+ gpio = <&pio 7 0 0>; /* PH0 */
+ status = "okay";
+ };
+
+ reg_usb2_vbus: usb2-vbus {
+ pinctrl-0 = <&usb2_vbus_pin_bananapro>;
+ gpio = <&pio 7 1 0>; /* PH1 */
+ status = "okay";
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_power_pin_bananapi>;
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 7 23 0>;
+ };
+
+ reg_vmmc3: vmmc3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vmmc3_pin_bananapro>;
+ regulator-name = "vmmc3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&pio 7 22 0>;
+ };
+};
--
2.1.0
More information about the linux-arm-kernel
mailing list