[PATCH v6 1/6] input: touchscreen: ti_am335x_tsc Interchange touchscreen and ADC steps

Vignesh R vigneshr at ti.com
Tue Jan 6 21:49:34 PST 2015


From: Brad Griffis <bgriffis at ti.com>

This patch makes the initial changes required to workaround TSC-false
pen-up interrupts. It is required to implement these changes in order to
remove udelay in the TSC interrupt handler and false pen-up events.
The charge step is to be executed immediately after sampling X+. Hence
TSC is made to use higher numbered steps (steps 5 to 16 for 5 co-ordinate
readouts, 4 wire TSC configuration) and ADC to use lower ones. Further
X co-ordinate readouts must be the last to be sampled, thus co-ordinates
are sampled in the order Y-Z-X.

Signed-off-by: Brad Griffis <bgriffis at ti.com>
[vigneshr at ti.com: Ported the patch from v3.12 to v3.19rc1]

Signed-off-by: Vignesh R <vigneshr at ti.com>
Acked-by: Jonathan Cameron <jic23 at kernel.org>
---
 drivers/iio/adc/ti_am335x_adc.c           |  5 ++--
 drivers/input/touchscreen/ti_am335x_tsc.c | 42 ++++++++++++++++++-------------
 2 files changed, 26 insertions(+), 21 deletions(-)

diff --git a/drivers/iio/adc/ti_am335x_adc.c b/drivers/iio/adc/ti_am335x_adc.c
index b730864731e8..adba23246474 100644
--- a/drivers/iio/adc/ti_am335x_adc.c
+++ b/drivers/iio/adc/ti_am335x_adc.c
@@ -86,19 +86,18 @@ static void tiadc_step_config(struct iio_dev *indio_dev)
 {
 	struct tiadc_device *adc_dev = iio_priv(indio_dev);
 	unsigned int stepconfig;
-	int i, steps;
+	int i, steps = 0;
 
 	/*
 	 * There are 16 configurable steps and 8 analog input
 	 * lines available which are shared between Touchscreen and ADC.
 	 *
-	 * Steps backwards i.e. from 16 towards 0 are used by ADC
+	 * Steps forwards i.e. from 0 towards 16 are used by ADC
 	 * depending on number of input lines needed.
 	 * Channel would represent which analog input
 	 * needs to be given to ADC to digitalize data.
 	 */
 
-	steps = TOTAL_STEPS - adc_dev->channels;
 	if (iio_buffer_enabled(indio_dev))
 		stepconfig = STEPCONFIG_AVG_16 | STEPCONFIG_FIFO1
 					| STEPCONFIG_MODE_SWCNT;
diff --git a/drivers/input/touchscreen/ti_am335x_tsc.c b/drivers/input/touchscreen/ti_am335x_tsc.c
index 004f1346a957..dfbb9fe6a270 100644
--- a/drivers/input/touchscreen/ti_am335x_tsc.c
+++ b/drivers/input/touchscreen/ti_am335x_tsc.c
@@ -121,7 +121,7 @@ static void titsc_step_config(struct titsc *ts_dev)
 {
 	unsigned int	config;
 	int i;
-	int end_step;
+	int end_step, first_step, tsc_steps;
 	u32 stepenable;
 
 	config = STEPCONFIG_MODE_HWSYNC |
@@ -140,9 +140,11 @@ static void titsc_step_config(struct titsc *ts_dev)
 		break;
 	}
 
-	/* 1 … coordinate_readouts is for X */
-	end_step = ts_dev->coordinate_readouts;
-	for (i = 0; i < end_step; i++) {
+	tsc_steps = ts_dev->coordinate_readouts * 2 + 2;
+	first_step = TOTAL_STEPS - tsc_steps;
+	/* Steps 16 to 16-coordinate_readouts is for X */
+	end_step = first_step + tsc_steps;
+	for (i = end_step - ts_dev->coordinate_readouts; i < end_step; i++) {
 		titsc_writel(ts_dev, REG_STEPCONFIG(i), config);
 		titsc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
 	}
@@ -164,9 +166,9 @@ static void titsc_step_config(struct titsc *ts_dev)
 		break;
 	}
 
-	/* coordinate_readouts … coordinate_readouts * 2 is for Y */
-	end_step = ts_dev->coordinate_readouts * 2;
-	for (i = ts_dev->coordinate_readouts; i < end_step; i++) {
+	/* 1 ... coordinate_readouts is for Y */
+	end_step = first_step + ts_dev->coordinate_readouts;
+	for (i = first_step; i < end_step; i++) {
 		titsc_writel(ts_dev, REG_STEPCONFIG(i), config);
 		titsc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
 	}
@@ -179,7 +181,7 @@ static void titsc_step_config(struct titsc *ts_dev)
 	titsc_writel(ts_dev, REG_CHARGECONFIG, config);
 	titsc_writel(ts_dev, REG_CHARGEDELAY, CHARGEDLY_OPENDLY);
 
-	/* coordinate_readouts * 2 … coordinate_readouts * 2 + 2 is for Z */
+	/* coordinate_readouts + 1 ... coordinate_readouts + 2 is for Z */
 	config = STEPCONFIG_MODE_HWSYNC |
 			STEPCONFIG_AVG_16 | ts_dev->bit_yp |
 			ts_dev->bit_xn | STEPCONFIG_INM_ADCREFM |
@@ -194,8 +196,11 @@ static void titsc_step_config(struct titsc *ts_dev)
 	titsc_writel(ts_dev, REG_STEPDELAY(end_step),
 			STEPCONFIG_OPENDLY);
 
-	/* The steps1 … end and bit 0 for TS_Charge */
-	stepenable = (1 << (end_step + 2)) - 1;
+	/* The steps end ... end - readouts * 2 + 2 and bit 0 for TS_Charge */
+	stepenable = 1;
+	for (i = 0; i < tsc_steps; i++)
+		stepenable |= 1 << (first_step + i + 1);
+
 	ts_dev->step_mask = stepenable;
 	am335x_tsc_se_set_cache(ts_dev->mfd_tscadc, ts_dev->step_mask);
 }
@@ -209,6 +214,7 @@ static void titsc_read_coordinates(struct titsc *ts_dev,
 	unsigned int read, diff;
 	unsigned int i, channel;
 	unsigned int creads = ts_dev->coordinate_readouts;
+	unsigned int first_step = TOTAL_STEPS - (creads * 2 + 2);
 
 	*z1 = *z2 = 0;
 	if (fifocount % (creads * 2 + 2))
@@ -226,7 +232,7 @@ static void titsc_read_coordinates(struct titsc *ts_dev,
 
 		channel = (read & 0xf0000) >> 16;
 		read &= 0xfff;
-		if (channel < creads) {
+		if (channel > first_step + creads + 2) {
 			diff = abs(read - prev_val_x);
 			if (diff < prev_diff_x) {
 				prev_diff_x = diff;
@@ -234,19 +240,19 @@ static void titsc_read_coordinates(struct titsc *ts_dev,
 			}
 			prev_val_x = read;
 
-		} else if (channel < creads * 2) {
+		} else if (channel == first_step + creads + 1) {
+			*z1 = read;
+
+		} else if (channel == first_step + creads + 2) {
+			*z2 = read;
+
+		} else if (channel > first_step) {
 			diff = abs(read - prev_val_y);
 			if (diff < prev_diff_y) {
 				prev_diff_y = diff;
 				*y = read;
 			}
 			prev_val_y = read;
-
-		} else if (channel < creads * 2 + 1) {
-			*z1 = read;
-
-		} else if (channel < creads * 2 + 2) {
-			*z2 = read;
 		}
 	}
 }
-- 
1.9.1




More information about the linux-arm-kernel mailing list