[PATCH 12/17] ARM: dts: sun5i: hsg-h702: add axp209 regulator nodes

[Chen-Yu Tsai]

This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.

The regulator names and constraints are based on the board
schematics and the SoC datasheet.

DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.

LDO3 powers the USB WiFi module. This patch also references it
from the usb-phy node.

Also get rid of axp209 properties already set in axp209.dtsi.

Signed-off-by: Chen-Yu Tsai <wens at csie.org>
---
 arch/arm/boot/dts/sun5i-a13-hsg-h702.dts | 46 ++++++++++++++++++++++++++------
 1 file changed, 38 insertions(+), 8 deletions(-)

diff --git a/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts b/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts
index eeed1f236ee8..ec9b2e4e25ee 100644
--- a/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts
+++ b/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts
@@ -65,11 +65,7 @@
 		};
 
 		usbphy: phy at 01c13400 {
-			/*
-			 * There doesn't seem to be a GPIO for controlling
-			 * usb1 vbus, despite the fex file saying otherwise.
-			 */
-			usb1_vbus-supply = <&reg_vcc5v0>;
+			usb1_vbus-supply = <&reg_ldo3>;
 			status = "okay";
 		};
 
@@ -102,11 +98,8 @@
 			status = "okay";
 
 			axp209: pmic at 34 {
-				compatible = "x-powers,axp209";
 				reg = <0x34>;
 				interrupts = <0>;
-				interrupt-controller;
-				#interrupt-cells = <1>;
 			};
 		};
 
@@ -128,3 +121,40 @@
 		};
 	};
 };
+
+/include/ "axp209.dtsi"
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_ldo3 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
-- 
2.1.4