[PATCH 1/3] thermal: exynos: Add the support for Exynos5433 TMU
Chanwoo Choi
cw00.choi at samsung.com
Thu Feb 26 03:35:19 PST 2015
This patch adds the support for Exynos5433's TMU (Thermal Management Unit).
Exynos5433 has a little different register bit fields as following description:
- Support the eight trip points for rising/falling interrupt by using two registers
- Read the calibration type (1-point or 2-point) and sensor id from TRIMINFO register
- Use a little different register address
Cc: Zhang Rui <rui.zhang at intel.com>
Cc: Eduardo Valentin <edubezval at gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi at samsung.com>
---
drivers/thermal/samsung/exynos_tmu.c | 161 +++++++++++++++++++++++++++++++++--
drivers/thermal/samsung/exynos_tmu.h | 1 +
2 files changed, 157 insertions(+), 5 deletions(-)
diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c
index 1d30b09..1bb2fb7 100644
--- a/drivers/thermal/samsung/exynos_tmu.c
+++ b/drivers/thermal/samsung/exynos_tmu.c
@@ -97,6 +97,32 @@
#define EXYNOS4412_MUX_ADDR_VALUE 6
#define EXYNOS4412_MUX_ADDR_SHIFT 20
+/* Exynos5433 specific registers */
+#define EXYNOS5433_TMU_REG_CONTROL1 0x024
+#define EXYNOS5433_TMU_SAMPLING_INTERVAL 0x02c
+#define EXYNOS5433_TMU_COUNTER_VALUE0 0x030
+#define EXYNOS5433_TMU_COUNTER_VALUE1 0x034
+#define EXYNOS5433_TMU_REG_CURRENT_TEMP1 0x044
+#define EXYNOS5433_THD_TEMP_RISE3_0 0x050
+#define EXYNOS5433_THD_TEMP_RISE7_4 0x054
+#define EXYNOS5433_THD_TEMP_FALL3_0 0x060
+#define EXYNOS5433_THD_TEMP_FALL7_4 0x064
+#define EXYNOS5433_TMU_REG_INTEN 0x0c0
+#define EXYNOS5433_TMU_REG_INTPEND 0x0c8
+#define EXYNOS5433_TMU_EMUL_CON 0x110
+#define EXYNOS5433_TMU_PD_DET_EN 0x130
+
+#define EXYNOS5433_TRIMINFO_SENSOR_ID_SHIFT 16
+#define EXYNOS5433_TRIMINFO_CALIB_SEL_SHIFT 23
+#define EXYNOS5433_TRIMINFO_SENSOR_ID_MASK \
+ (0xf << EXYNOS5433_TRIMINFO_SENSOR_ID_SHIFT)
+#define EXYNOS5433_TRIMINFO_CALIB_SEL_MASK BIT(23)
+
+#define EXYNOS5433_TRIMINFO_ONE_POINT_TRIMMING 0
+#define EXYNOS5433_TRIMINFO_TWO_POINT_TRIMMING 1
+
+#define EXYNOS5433_PD_DET_EN 1
+
/*exynos5440 specific registers*/
#define EXYNOS5440_TMU_S0_7_TRIM 0x000
#define EXYNOS5440_TMU_S0_7_CTRL 0x020
@@ -484,6 +510,101 @@ out:
return ret;
}
+static int exynos5433_tmu_initialize(struct platform_device *pdev)
+{
+ struct exynos_tmu_data *data = platform_get_drvdata(pdev);
+ struct exynos_tmu_platform_data *pdata = data->pdata;
+ struct thermal_zone_device *tz = data->tzd;
+ unsigned int status, trim_info;
+ unsigned int rising_threshold = 0, falling_threshold = 0;
+ unsigned long temp, temp_hist;
+ int ret = 0, threshold_code, i, sensor_id, cal_type;
+
+ status = readb(data->base + EXYNOS_TMU_REG_STATUS);
+ if (!status) {
+ ret = -EBUSY;
+ goto out;
+ }
+
+ trim_info = readl(data->base + EXYNOS_TMU_REG_TRIMINFO);
+ sanitize_temp_error(data, trim_info);
+
+ /* Read the temperature sensor id */
+ sensor_id = (trim_info & EXYNOS5433_TRIMINFO_SENSOR_ID_MASK)
+ >> EXYNOS5433_TRIMINFO_SENSOR_ID_SHIFT;
+ dev_info(&pdev->dev, "Temperature sensor ID: 0x%x\n", sensor_id);
+
+ /* Read the calibration mode */
+ writel(trim_info, data->base + EXYNOS_TMU_REG_TRIMINFO);
+ cal_type = (trim_info & EXYNOS5433_TRIMINFO_CALIB_SEL_MASK)
+ >> EXYNOS5433_TRIMINFO_CALIB_SEL_SHIFT;
+
+ switch (cal_type) {
+ case EXYNOS5433_TRIMINFO_ONE_POINT_TRIMMING:
+ pdata->cal_type = TYPE_ONE_POINT_TRIMMING;
+ break;
+ case EXYNOS5433_TRIMINFO_TWO_POINT_TRIMMING:
+ pdata->cal_type = TYPE_TWO_POINT_TRIMMING;
+ break;
+ default:
+ pdata->cal_type = TYPE_ONE_POINT_TRIMMING;
+ break;
+ };
+
+ dev_info(&pdev->dev, "Calibration type is %d-point calibration\n",
+ cal_type ? 2 : 1);
+
+ /* Write temperature code for rising and falling threshold */
+ for (i = 0; i < of_thermal_get_ntrips(tz); i++) {
+ int rising_reg_offset, falling_reg_offset;
+ int j = 0;
+
+ switch (i) {
+ case 0:
+ case 1:
+ case 2:
+ case 3:
+ rising_reg_offset = EXYNOS5433_THD_TEMP_RISE3_0;
+ falling_reg_offset = EXYNOS5433_THD_TEMP_FALL3_0;
+ j = i;
+ break;
+ case 4:
+ case 5:
+ case 6:
+ case 7:
+ rising_reg_offset = EXYNOS5433_THD_TEMP_RISE7_4;
+ falling_reg_offset = EXYNOS5433_THD_TEMP_FALL7_4;
+ j = i - 4;
+ break;
+ default:
+ continue;
+ }
+
+ /* Write temperature code for rising threshold */
+ tz->ops->get_trip_temp(tz, i, &temp);
+ temp /= MCELSIUS;
+ threshold_code = temp_to_code(data, temp);
+
+ rising_threshold = readl(data->base + rising_reg_offset);
+ rising_threshold |= (threshold_code << j * 8);
+ writel(rising_threshold, data->base + rising_reg_offset);
+
+ /* Write temperature code for falling threshold */
+ tz->ops->get_trip_hyst(tz, i, &temp_hist);
+ temp_hist = temp - (temp_hist / MCELSIUS);
+ threshold_code = temp_to_code(data, temp_hist);
+
+ falling_threshold = readl(data->base + falling_reg_offset);
+ falling_threshold &= ~(0xff << j * 8);
+ falling_threshold |= (threshold_code << j * 8);
+ writel(falling_threshold, data->base + falling_reg_offset);
+ }
+
+ data->tmu_clear_irqs(data);
+out:
+ return ret;
+}
+
static int exynos5440_tmu_initialize(struct platform_device *pdev)
{
struct exynos_tmu_data *data = platform_get_drvdata(pdev);
@@ -682,7 +803,8 @@ static void exynos7_tmu_control(struct platform_device *pdev, bool on)
if (on) {
con |= (1 << EXYNOS_TMU_CORE_EN_SHIFT);
- con |= (1 << EXYNOS7_PD_DET_EN_SHIFT);
+ if (data->soc == SOC_ARCH_EXYNOS7)
+ con |= (1 << EXYNOS7_PD_DET_EN_SHIFT);
interrupt_en =
(of_thermal_is_trip_valid(tz, 7)
<< EXYNOS7_TMU_INTEN_RISE7_SHIFT) |
@@ -705,11 +827,20 @@ static void exynos7_tmu_control(struct platform_device *pdev, bool on)
interrupt_en << EXYNOS_TMU_INTEN_FALL0_SHIFT;
} else {
con &= ~(1 << EXYNOS_TMU_CORE_EN_SHIFT);
- con &= ~(1 << EXYNOS7_PD_DET_EN_SHIFT);
+ if (data->soc == SOC_ARCH_EXYNOS7)
+ con &= ~(1 << EXYNOS7_PD_DET_EN_SHIFT);
interrupt_en = 0; /* Disable all interrupts */
}
- writel(interrupt_en, data->base + EXYNOS7_TMU_REG_INTEN);
+ if (data->soc == SOC_ARCH_EXYNOS5433) {
+ int pd_det_en = on ? EXYNOS5433_PD_DET_EN : 0;
+
+ writel(pd_det_en, data->base + EXYNOS5433_TMU_PD_DET_EN);
+ writel(interrupt_en, data->base + EXYNOS5433_TMU_REG_INTEN);
+ } else {
+ writel(interrupt_en, data->base + EXYNOS7_TMU_REG_INTEN);
+ }
+
writel(con, data->base + EXYNOS_TMU_REG_CONTROL);
}
@@ -770,6 +901,8 @@ static void exynos4412_tmu_set_emulation(struct exynos_tmu_data *data,
if (data->soc == SOC_ARCH_EXYNOS5260)
emul_con = EXYNOS5260_EMUL_CON;
+ if (data->soc == SOC_ARCH_EXYNOS5433)
+ emul_con = EXYNOS5433_TMU_EMUL_CON;
else if (data->soc == SOC_ARCH_EXYNOS7)
emul_con = EXYNOS7_TMU_REG_EMUL_CON;
else
@@ -882,6 +1015,9 @@ static void exynos4210_tmu_clear_irqs(struct exynos_tmu_data *data)
} else if (data->soc == SOC_ARCH_EXYNOS7) {
tmu_intstat = EXYNOS7_TMU_REG_INTPEND;
tmu_intclear = EXYNOS7_TMU_REG_INTPEND;
+ } else if (data->soc == SOC_ARCH_EXYNOS5433) {
+ tmu_intstat = EXYNOS5433_TMU_REG_INTPEND;
+ tmu_intclear = EXYNOS5433_TMU_REG_INTPEND;
} else {
tmu_intstat = EXYNOS_TMU_REG_INTSTAT;
tmu_intclear = EXYNOS_TMU_REG_INTCLEAR;
@@ -926,6 +1062,7 @@ static const struct of_device_id exynos_tmu_match[] = {
{ .compatible = "samsung,exynos5260-tmu", },
{ .compatible = "samsung,exynos5420-tmu", },
{ .compatible = "samsung,exynos5420-tmu-ext-triminfo", },
+ { .compatible = "samsung,exynos5433-tmu", },
{ .compatible = "samsung,exynos5440-tmu", },
{ .compatible = "samsung,exynos7-tmu", },
{ /* sentinel */ },
@@ -949,6 +1086,8 @@ static int exynos_of_get_soc_type(struct device_node *np)
else if (of_device_is_compatible(np,
"samsung,exynos5420-tmu-ext-triminfo"))
return SOC_ARCH_EXYNOS5420_TRIMINFO;
+ else if (of_device_is_compatible(np, "samsung,exynos5433-tmu"))
+ return SOC_ARCH_EXYNOS5433;
else if (of_device_is_compatible(np, "samsung,exynos5440-tmu"))
return SOC_ARCH_EXYNOS5440;
else if (of_device_is_compatible(np, "samsung,exynos7-tmu"))
@@ -1069,6 +1208,13 @@ static int exynos_map_dt_data(struct platform_device *pdev)
data->tmu_set_emulation = exynos4412_tmu_set_emulation;
data->tmu_clear_irqs = exynos4210_tmu_clear_irqs;
break;
+ case SOC_ARCH_EXYNOS5433:
+ data->tmu_initialize = exynos5433_tmu_initialize;
+ data->tmu_control = exynos7_tmu_control;
+ data->tmu_read = exynos4412_tmu_read;
+ data->tmu_set_emulation = exynos4412_tmu_set_emulation;
+ data->tmu_clear_irqs = exynos4210_tmu_clear_irqs;
+ break;
case SOC_ARCH_EXYNOS5440:
data->tmu_initialize = exynos5440_tmu_initialize;
data->tmu_control = exynos5440_tmu_control;
@@ -1172,7 +1318,9 @@ static int exynos_tmu_probe(struct platform_device *pdev)
goto err_clk_sec;
}
- if (data->soc == SOC_ARCH_EXYNOS7) {
+ switch (data->soc) {
+ case SOC_ARCH_EXYNOS5433:
+ case SOC_ARCH_EXYNOS7:
data->sclk = devm_clk_get(&pdev->dev, "tmu_sclk");
if (IS_ERR(data->sclk)) {
dev_err(&pdev->dev, "Failed to get sclk\n");
@@ -1184,7 +1332,10 @@ static int exynos_tmu_probe(struct platform_device *pdev)
goto err_clk;
}
}
- }
+ break;
+ default:
+ break;
+ };
ret = exynos_tmu_initialize(pdev);
if (ret) {
diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h
index 4d71ec6..440c714 100644
--- a/drivers/thermal/samsung/exynos_tmu.h
+++ b/drivers/thermal/samsung/exynos_tmu.h
@@ -33,6 +33,7 @@ enum soc_type {
SOC_ARCH_EXYNOS5260,
SOC_ARCH_EXYNOS5420,
SOC_ARCH_EXYNOS5420_TRIMINFO,
+ SOC_ARCH_EXYNOS5433,
SOC_ARCH_EXYNOS5440,
SOC_ARCH_EXYNOS7,
};
--
1.8.5.5
More information about the linux-arm-kernel
mailing list