[PATCH v2 2/2] remoteproc: microblaze: Add support for microblaze on Zynq
Michal Simek
michal.simek at xilinx.com
Mon Feb 23 03:37:26 PST 2015
Xilinx Microblaze is placed in programmable logic on Xilinx
Zynq architecture. Driver requires specific HW setting
described in DT binding.
Signed-off-by: Michal Simek <michal.simek at xilinx.com>
---
Changes in v2:
- Rebase on 4.0-rc1
- remove DEBUG_SG dependency - Reported-by: Nathan Lynch
<Nathan_Lynch at mentor.com>
- Changes caused by DT binding change Reported-by: Mark Rutland
<mark.rutland at arm.com> - https://lkml.org/lkml/2015/1/19/198
- Use const in mb_remoteproc_match[] reported by checkpatch.pl.
MAINTAINERS | 1 +
drivers/remoteproc/Kconfig | 11 +
drivers/remoteproc/Makefile | 1 +
drivers/remoteproc/mb_remoteproc.c | 427 +++++++++++++++++++++++++++++++++++++
4 files changed, 440 insertions(+)
create mode 100644 drivers/remoteproc/mb_remoteproc.c
diff --git a/MAINTAINERS b/MAINTAINERS
index ddc5a8cf9a8a..451a1f0cf4a5 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1606,6 +1606,7 @@ F: drivers/clocksource/cadence_ttc_timer.c
F: drivers/i2c/busses/i2c-cadence.c
F: drivers/mmc/host/sdhci-of-arasan.c
F: drivers/edac/synopsys_edac.c
+F: drivers/remoteproc/mb_remoteproc.c
ARM SMMU DRIVER
M: Will Deacon <will.deacon at arm.com>
diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig
index 5e343bab9458..d119c2728a7b 100644
--- a/drivers/remoteproc/Kconfig
+++ b/drivers/remoteproc/Kconfig
@@ -64,4 +64,15 @@ config DA8XX_REMOTEPROC
It's safe to say n here if you're not interested in multimedia
offloading.
+config MB_REMOTEPROC
+ tristate "Support Microblaze remoteproc"
+ depends on ARCH_ZYNQ
+ select GPIO_XILINX
+ select REMOTEPROC
+ select RPMSG
+ default m
+ help
+ Say y here to support Xilinx Microblaze remote processors
+ on the Xilinx Zynq.
+
endmenu
diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile
index ac2ff75686d2..40e247ffac34 100644
--- a/drivers/remoteproc/Makefile
+++ b/drivers/remoteproc/Makefile
@@ -10,3 +10,4 @@ remoteproc-y += remoteproc_elf_loader.o
obj-$(CONFIG_OMAP_REMOTEPROC) += omap_remoteproc.o
obj-$(CONFIG_STE_MODEM_RPROC) += ste_modem_rproc.o
obj-$(CONFIG_DA8XX_REMOTEPROC) += da8xx_remoteproc.o
+obj-$(CONFIG_MB_REMOTEPROC) += mb_remoteproc.o
diff --git a/drivers/remoteproc/mb_remoteproc.c b/drivers/remoteproc/mb_remoteproc.c
new file mode 100644
index 000000000000..7febf32abafc
--- /dev/null
+++ b/drivers/remoteproc/mb_remoteproc.c
@@ -0,0 +1,427 @@
+/*
+ * Microblaze Remote Processor driver
+ *
+ * Copyright (C) 2012 - 2015 Michal Simek <monstr at monstr.eu>
+ * Copyright (C) 2013 - 2015 Xilinx, Inc.
+ * Copyright (C) 2012 PetaLogix
+ *
+ * Based on origin OMAP Remote Processor driver
+ *
+ * Copyright (C) 2011 Texas Instruments, Inc.
+ * Copyright (C) 2011 Google, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/remoteproc.h>
+#include <linux/interrupt.h>
+#include <linux/of_irq.h>
+#include <linux/of_gpio.h>
+#include <linux/of_platform.h>
+#include <linux/smp.h>
+#include <linux/irqchip/arm-gic.h>
+#include <asm/outercache.h>
+#include <asm/cacheflush.h>
+#include <linux/slab.h>
+#include <linux/cpu.h>
+#include <linux/gpio.h>
+#include <linux/io.h>
+#include <linux/delay.h>
+
+#include "remoteproc_internal.h"
+
+/* Module parameter */
+static char *firmware;
+
+/* Private data */
+struct mb_rproc_pdata {
+ struct rproc *rproc;
+ u32 mem_start;
+ u32 mem_end;
+ int reset_gpio;
+ int mb_debug_gpio;
+ int ipi;
+ int vring0;
+ int vring1;
+ void __iomem *vbase;
+ const unsigned char *bootloader;
+};
+
+/* Store rproc for IPI handler */
+static struct platform_device *remoteprocdev;
+static struct work_struct workqueue;
+
+static void handle_event(struct work_struct *work)
+{
+ struct mb_rproc_pdata *local = platform_get_drvdata(remoteprocdev);
+
+ flush_cache_all();
+ outer_flush_range(local->mem_start, local->mem_end);
+
+ if (rproc_vq_interrupt(local->rproc, 0) == IRQ_NONE)
+ dev_info(&remoteprocdev->dev, "no message found in vqid 0\n");
+}
+
+static irqreturn_t ipi_kick(int irq, void *dev_id)
+{
+ dev_dbg(&remoteprocdev->dev, "KICK Linux because of pending message\n");
+ schedule_work(&workqueue);
+ dev_dbg(&remoteprocdev->dev, "KICK Linux handled\n");
+
+ return IRQ_HANDLED;
+}
+
+static int mb_rproc_start(struct rproc *rproc)
+{
+ struct device *dev = rproc->dev.parent;
+ struct platform_device *pdev = to_platform_device(dev);
+ struct mb_rproc_pdata *local = platform_get_drvdata(pdev);
+ const struct firmware *fw;
+ int ret;
+
+ dev_info(dev, "%s\n", __func__);
+ INIT_WORK(&workqueue, handle_event);
+
+ flush_cache_all();
+ outer_flush_range(local->mem_start, local->mem_end);
+
+ remoteprocdev = pdev;
+
+ ret = request_firmware(&fw, local->bootloader, &pdev->dev);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "request_firmware failed\n");
+ return ret;
+ }
+ /* Copy bootloader to memory */
+ memcpy(local->vbase, fw->data, fw->size);
+ release_firmware(fw);
+
+ /* Just for sure synchronize memories */
+ dsb();
+
+ /* Release Microblaze from reset */
+ gpio_set_value(local->reset_gpio, 0);
+
+ return 0;
+}
+
+/* kick a firmware */
+static void mb_rproc_kick(struct rproc *rproc, int vqid)
+{
+ struct device *dev = rproc->dev.parent;
+ struct platform_device *pdev = to_platform_device(dev);
+ struct mb_rproc_pdata *local = platform_get_drvdata(pdev);
+
+ dev_dbg(dev, "KICK Firmware to start send messages vqid %d\n", vqid);
+
+ flush_cache_all();
+ outer_flush_all();
+
+ /* Send swirq to firmware */
+ gpio_set_value(local->vring0, 0);
+ gpio_set_value(local->vring1, 0);
+ dsb();
+
+ if (!vqid) {
+ udelay(500);
+ gpio_set_value(local->vring0, 1);
+ dsb();
+ } else {
+ udelay(100);
+ gpio_set_value(local->vring1, 1);
+ dsb();
+ }
+}
+
+/* power off the remote processor */
+static int mb_rproc_stop(struct rproc *rproc)
+{
+ struct device *dev = rproc->dev.parent;
+ struct platform_device *pdev = to_platform_device(dev);
+ struct mb_rproc_pdata *local = platform_get_drvdata(pdev);
+
+ /* Setup MB to the state where all memory transactions are done */
+ gpio_set_value(local->mb_debug_gpio, 1);
+ dsb(); /* Be sure that this write has been done */
+ /*
+ * This should be enough to ensure one CLK as
+ * it is written in MB ref guide
+ */
+ gpio_set_value(local->mb_debug_gpio, 0);
+
+ udelay(1000); /* Wait some time to finish all mem transactions */
+
+ /* Add Microblaze to reset state */
+ gpio_set_value(local->reset_gpio, 1);
+
+ /* No reason to wait that operations where done */
+ return 0;
+}
+
+static struct rproc_ops mb_rproc_ops = {
+ .start = mb_rproc_start,
+ .stop = mb_rproc_stop,
+ .kick = mb_rproc_kick,
+};
+
+/* Just to detect bug if interrupt forwarding is broken */
+static irqreturn_t mb_remoteproc_interrupt(int irq, void *dev_id)
+{
+ struct device *dev = dev_id;
+
+ dev_err(dev, "GIC IRQ %d is not forwarded correctly\n", irq);
+
+ return IRQ_HANDLED;
+}
+
+static int mb_remoteproc_probe(struct platform_device *pdev)
+{
+ const unsigned char *prop;
+ struct platform_device *bram_pdev;
+ struct device_node *bram_dev;
+ struct resource *res; /* IO mem resources */
+ int ret = 0;
+ int count = 0;
+ struct mb_rproc_pdata *local;
+
+ local = devm_kzalloc(&pdev->dev, sizeof(*local), GFP_KERNEL);
+ if (!local)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, local);
+
+ /* Declare memory for firmware */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "invalid address\n");
+ return -ENODEV;
+ }
+
+ local->mem_start = res->start;
+ local->mem_end = res->end;
+
+ /* Alloc phys addr from 0 to max_addr for firmware */
+ ret = dma_declare_coherent_memory(&pdev->dev, local->mem_start,
+ local->mem_start, local->mem_end - local->mem_start + 1,
+ DMA_MEMORY_IO);
+ if (!ret) {
+ dev_err(&pdev->dev, "dma_declare_coherent_memory failed\n");
+ return -ENOMEM;
+ }
+
+ ret = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
+ if (ret) {
+ dev_err(&pdev->dev, "dma_set_coherent_mask: %d\n", ret);
+ goto dma_mask_fault;
+ }
+
+ /* Alloc IRQ based on DTS to be sure that no other driver will use it */
+ while (1) {
+ int irq;
+ /* Allocating shared IRQs will ensure that any module will
+ * use these IRQs */
+ irq = platform_get_irq(pdev, count++);
+ if (irq == -ENXIO || irq == -EINVAL)
+ break;
+ ret = devm_request_irq(&pdev->dev, irq, mb_remoteproc_interrupt,
+ 0, dev_name(&pdev->dev), &pdev->dev);
+ if (ret) {
+ dev_err(&pdev->dev, "IRQ %d already allocated\n", irq);
+ goto dma_mask_fault;
+ }
+
+ dev_info(&pdev->dev, "%d: Alloc irq: %d\n", count, irq);
+ }
+
+ /* Find out reset gpio and keep microblaze in reset */
+ local->reset_gpio = of_get_named_gpio(pdev->dev.of_node,
+ "reset-gpio", 0);
+ if (local->reset_gpio < 0) {
+ dev_err(&pdev->dev, "reset-gpio property not found\n");
+ ret = local->reset_gpio;
+ goto dma_mask_fault;
+ }
+ ret = devm_gpio_request_one(&pdev->dev, local->reset_gpio,
+ GPIOF_OUT_INIT_HIGH, "mb_reset");
+ if (ret) {
+ dev_err(&pdev->dev, "Please specify gpio reset addr\n");
+ goto dma_mask_fault;
+ }
+
+ /* Find out reset gpio and keep microblaze in reset */
+ local->mb_debug_gpio = of_get_named_gpio(pdev->dev.of_node,
+ "debug-gpio", 0);
+ if (local->mb_debug_gpio < 0) {
+ dev_err(&pdev->dev, "mb-debug-gpio property not found\n");
+ ret = local->mb_debug_gpio;
+ goto dma_mask_fault;
+ }
+ ret = devm_gpio_request_one(&pdev->dev, local->mb_debug_gpio,
+ GPIOF_OUT_INIT_LOW, "mb_debug");
+ if (ret) {
+ dev_err(&pdev->dev, "Please specify gpio debug pin\n");
+ goto dma_mask_fault;
+ }
+
+ /* IPI number for getting irq from firmware */
+ local->ipi = of_get_named_gpio(pdev->dev.of_node, "ipino-gpio", 0);
+ if (local->ipi < 0) {
+ dev_err(&pdev->dev, "ipi-gpio property not found\n");
+ ret = local->ipi;
+ goto dma_mask_fault;
+ }
+ ret = devm_gpio_request_one(&pdev->dev, local->ipi, GPIOF_IN, "mb_ipi");
+ if (ret) {
+ dev_err(&pdev->dev, "Please specify gpio reset addr\n");
+ goto dma_mask_fault;
+ }
+ ret = devm_request_irq(&pdev->dev, gpio_to_irq(local->ipi),
+ ipi_kick, IRQF_SHARED|IRQF_TRIGGER_RISING,
+ dev_name(&pdev->dev), local);
+ if (ret) {
+ dev_err(&pdev->dev, "IRQ %d already allocated\n", local->ipi);
+ goto dma_mask_fault;
+ }
+
+ /* Find out vring0 pin */
+ local->vring0 = of_get_named_gpio(pdev->dev.of_node, "vring0-gpio", 0);
+ if (local->vring0 < 0) {
+ dev_err(&pdev->dev, "reset-gpio property not found\n");
+ ret = local->vring0;
+ goto dma_mask_fault;
+ }
+ ret = devm_gpio_request_one(&pdev->dev, local->vring0,
+ GPIOF_DIR_OUT, "mb_vring0");
+ if (ret) {
+ dev_err(&pdev->dev, "Please specify gpio reset addr\n");
+ goto dma_mask_fault;
+ }
+
+ /* Find out vring1 pin */
+ local->vring1 = of_get_named_gpio(pdev->dev.of_node, "vring1-gpio", 0);
+ if (local->vring1 < 0) {
+ dev_err(&pdev->dev, "reset-gpio property not found\n");
+ ret = local->vring1;
+ goto dma_mask_fault;
+ }
+ ret = devm_gpio_request_one(&pdev->dev, local->vring1,
+ GPIOF_DIR_OUT, "mb_vring1");
+ if (ret) {
+ dev_err(&pdev->dev, "Please specify gpio reset addr\n");
+ goto dma_mask_fault;
+ }
+
+ /* Allocate bram device */
+ bram_dev = of_parse_phandle(pdev->dev.of_node, "bram", 0);
+ if (!bram_dev) {
+ dev_err(&pdev->dev, "Please specify bram connection\n");
+ ret = -ENODEV;
+ goto dma_mask_fault;
+ }
+ bram_pdev = of_find_device_by_node(bram_dev);
+ if (!bram_pdev) {
+ dev_err(&pdev->dev, "BRAM device hasn't found\n");
+ ret = -ENODEV;
+ goto dma_mask_fault;
+ }
+ res = platform_get_resource(bram_pdev, IORESOURCE_MEM, 0);
+ local->vbase = devm_ioremap_resource(&pdev->dev, res);
+ if (!local->vbase) {
+ ret = -ENODEV;
+ goto dma_mask_fault;
+ }
+
+ /* Load simple bootloader to bram */
+ local->bootloader = of_get_property(pdev->dev.of_node,
+ "bram-firmware", NULL);
+ if (!local->bootloader) {
+ dev_err(&pdev->dev, "Please specify BRAM firmware\n");
+ ret = -ENODEV;
+ goto dma_mask_fault;
+ }
+
+ dev_info(&pdev->dev, "Using microblaze BRAM bootloader: %s\n",
+ local->bootloader);
+
+ /* Module param firmware first */
+ if (firmware)
+ prop = firmware;
+ else
+ prop = of_get_property(pdev->dev.of_node, "firmware", NULL);
+
+ if (prop) {
+ dev_info(&pdev->dev, "Using firmware: %s\n", prop);
+ local->rproc = rproc_alloc(&pdev->dev, dev_name(&pdev->dev),
+ &mb_rproc_ops, prop, sizeof(struct rproc));
+ if (!local->rproc) {
+ dev_err(&pdev->dev, "rproc allocation failed\n");
+ ret = -ENODEV;
+ goto dma_mask_fault;
+ }
+
+ ret = rproc_add(local->rproc);
+ if (ret) {
+ dev_err(&pdev->dev, "rproc registration failed\n");
+ rproc_put(local->rproc);
+ goto dma_mask_fault;
+ }
+ return 0;
+ }
+
+ ret = -ENODEV;
+
+dma_mask_fault:
+ dma_release_declared_memory(&pdev->dev);
+
+ return ret;
+}
+
+static int mb_remoteproc_remove(struct platform_device *pdev)
+{
+ struct mb_rproc_pdata *local = platform_get_drvdata(pdev);
+
+ dev_info(&pdev->dev, "%s\n", __func__);
+
+ dma_release_declared_memory(&pdev->dev);
+
+ rproc_del(local->rproc);
+ rproc_put(local->rproc);
+
+ return 0;
+}
+
+/* Match table for OF platform binding */
+static const struct of_device_id mb_remoteproc_match[] = {
+ { .compatible = "xlnx,mb-remoteproc", },
+ { /* end of list */ },
+};
+MODULE_DEVICE_TABLE(of, mb_remoteproc_match);
+
+static struct platform_driver mb_remoteproc_driver = {
+ .probe = mb_remoteproc_probe,
+ .remove = mb_remoteproc_remove,
+ .driver = {
+ .name = "mb-remoteproc",
+ .of_match_table = mb_remoteproc_match,
+ },
+};
+module_platform_driver(mb_remoteproc_driver);
+
+module_param(firmware, charp, 0);
+MODULE_PARM_DESC(firmware, "Override the firmware image name. Default value in DTS.");
+
+MODULE_AUTHOR("Michal Simek <monstr at monstr.eu");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Microblaze remote processor control driver");
--
1.8.2.3
More information about the linux-arm-kernel
mailing list