[PATCH v2 05/30] ARM: sun4i: ba10 tvbox: Convert to DT label based syntax

[Maxime Ripard]

In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax

Signed-off-by: Maxime Ripard <maxime.ripard at free-electrons.com>
---
 arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts | 168 ++++++++++++++---------------
 1 file changed, 83 insertions(+), 85 deletions(-)

diff --git a/arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts b/arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts
index 490b77c9bb36..bebb803a9456 100644
--- a/arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts
+++ b/arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts
@@ -54,95 +54,93 @@
 / {
 	model = "BA10 tvbox";
 	compatible = "allwinner,ba10-tvbox", "allwinner,sun4i-a10";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_pins_a>;
+	phy = <&phy1>;
+	status = "okay";
+};
 
-	soc at 01c00000 {
-		emac: ethernet at 01c0b000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&emac_pins_a>;
-			phy = <&phy1>;
-			status = "okay";
-		};
-
-		mdio at 01c0b080 {
-			status = "okay";
-
-			phy1: ethernet-phy at 1 {
-				reg = <1>;
-			};
-		};
-
-		mmc0: mmc at 01c0f000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
-			vmmc-supply = <&reg_vcc3v3>;
-			bus-width = <4>;
-			cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
-			cd-inverted;
-			status = "okay";
-		};
-
-		usbphy: phy at 01c13400 {
-			usb1_vbus-supply = <&reg_usb1_vbus>;
-			usb2_vbus-supply = <&reg_usb2_vbus>;
-			status = "okay";
-		};
-
-		ehci0: usb at 01c14000 {
-			status = "okay";
-		};
-
-		ohci0: usb at 01c14400 {
-			status = "okay";
-		};
-
-		ehci1: usb at 01c1c000 {
-			status = "okay";
-		};
-
-		ohci1: usb at 01c1c400 {
-			status = "okay";
-		};
-
-		pinctrl at 01c20800 {
-			usb2_vbus_pin_a: usb2_vbus_pin at 0 {
-				allwinner,pins = "PH12";
-			};
-		};
-
-		ir0: ir at 01c21800 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&ir0_pins_a>;
-			status = "okay";
-		};
-
-		uart0: serial at 01c28000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart0_pins_a>;
-			status = "okay";
-		};
-
-		i2c0: i2c at 01c2ac00 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c0_pins_a>;
-			status = "okay";
-
-			axp209: pmic at 34 {
-				compatible = "x-powers,axp209";
-				reg = <0x34>;
-				interrupts = <0>;
-
-				interrupt-controller;
-				#interrupt-cells = <1>;
-			};
-		};
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	axp209: pmic at 34 {
+		compatible = "x-powers,axp209";
+		reg = <0x34>;
+		interrupts = <0>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
 	};
+};
 
-	reg_usb1_vbus: usb1-vbus {
-		status = "okay";
+&ir0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir0_pins_a>;
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+
+	phy1: ethernet-phy at 1 {
+		reg = <1>;
 	};
+};
 
-	reg_usb2_vbus: usb2-vbus {
-		gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>;
-		status = "okay";
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+	cd-inverted;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pio {
+	usb2_vbus_pin_a: usb2_vbus_pin at 0 {
+		allwinner,pins = "PH12";
 	};
 };
+
+&reg_usb1_vbus {
+	status = "okay";
+};
+
+&reg_usb2_vbus {
+	gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};
-- 
2.3.0