[PATCH v2 25/30] ARM: sun7i: m3: Convert to DT label based syntax

[Maxime Ripard]

In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax

Signed-off-by: Maxime Ripard <maxime.ripard at free-electrons.com>
---
 arch/arm/boot/dts/sun7i-a20-m3.dts | 178 ++++++++++++++++++-------------------
 1 file changed, 88 insertions(+), 90 deletions(-)

diff --git a/arch/arm/boot/dts/sun7i-a20-m3.dts b/arch/arm/boot/dts/sun7i-a20-m3.dts
index 5add9f243ec3..44ba67dfb494 100644
--- a/arch/arm/boot/dts/sun7i-a20-m3.dts
+++ b/arch/arm/boot/dts/sun7i-a20-m3.dts
@@ -59,114 +59,112 @@
 	model = "Mele M3";
 	compatible = "mele,m3", "allwinner,sun7i-a20";
 
-	soc at 01c00000 {
-		mmc0: mmc at 01c0f000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
-			vmmc-supply = <&reg_vcc3v3>;
-			bus-width = <4>;
-			cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
-			cd-inverted;
-			status = "okay";
-		};
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_m3>;
 
-		mmc2: mmc at 01c11000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&mmc2_pins_a>;
-			vmmc-supply = <&reg_vcc3v3>;
-			bus-width = <4>;
-			non-removable;
-			status = "okay";
+		blue {
+			label = "m3:blue:usr";
+			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
 		};
+	};
+};
 
-		usbphy: phy at 01c13400 {
-			usb1_vbus-supply = <&reg_usb1_vbus>;
-			usb2_vbus-supply = <&reg_usb2_vbus>;
-			status = "okay";
-		};
+&ehci0 {
+	status = "okay";
+};
 
-		ehci0: usb at 01c14000 {
-			status = "okay";
-		};
+&ehci1 {
+	status = "okay";
+};
 
-		ohci0: usb at 01c14400 {
-			status = "okay";
-		};
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_pins_mii_a>;
+	phy = <&phy1>;
+	phy-mode = "mii";
+	status = "okay";
 
-		ehci1: usb at 01c1c000 {
-			status = "okay";
-		};
+	phy1: ethernet-phy at 1 {
+		reg = <1>;
+	};
+};
 
-		ohci1: usb at 01c1c400 {
-			status = "okay";
-		};
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
 
-		pinctrl at 01c20800 {
-			led_pins_m3: led_pins at 0 {
-				allwinner,pins = "PH20";
-				allwinner,function = "gpio_out";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-		};
+	axp209: pmic at 34 {
+		compatible = "x-powers,axp209";
+		reg = <0x34>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 
-		ir0: ir at 01c21800 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&ir0_pins_a>;
-			status = "okay";
-		};
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+};
 
-		uart0: serial at 01c28000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart0_pins_a>;
-			status = "okay";
-		};
+&ir0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir0_pins_a>;
+	status = "okay";
+};
 
-		i2c0: i2c at 01c2ac00 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c0_pins_a>;
-			status = "okay";
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+	cd-inverted;
+	status = "okay";
+};
 
-			axp209: pmic at 34 {
-				compatible = "x-powers,axp209";
-				reg = <0x34>;
-				interrupt-parent = <&nmi_intc>;
-				interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins_a>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
 
-				interrupt-controller;
-				#interrupt-cells = <1>;
-			};
-		};
+&ohci0 {
+	status = "okay";
+};
 
-		gmac: ethernet at 01c50000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&gmac_pins_mii_a>;
-			phy = <&phy1>;
-			phy-mode = "mii";
-			status = "okay";
+&ohci1 {
+	status = "okay";
+};
 
-			phy1: ethernet-phy at 1 {
-				reg = <1>;
-			};
-		};
+&pio {
+	led_pins_m3: led_pins at 0 {
+		allwinner,pins = "PH20";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 	};
+};
 
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins_m3>;
+&reg_usb1_vbus {
+	status = "okay";
+};
 
-		blue {
-			label = "m3:blue:usr";
-			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
-		};
-	};
+&reg_usb2_vbus {
+	status = "okay";
+};
 
-	reg_usb1_vbus: usb1-vbus {
-		status = "okay";
-	};
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
 
-	reg_usb2_vbus: usb2-vbus {
-		status = "okay";
-	};
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
 };
-- 
2.3.0