[PATCH v3 5/5] usb: phy: add phy-hi6220-usb
Zhangfei Gao
zhangfei.gao at linaro.org
Mon Feb 9 23:50:27 PST 2015
Add usb phy controller for hi6220 platform
Signed-off-by: Zhangfei Gao <zhangfei.gao at linaro.org>
---
drivers/usb/phy/Kconfig | 9 ++
drivers/usb/phy/Makefile | 1 +
drivers/usb/phy/phy-hi6220-usb.c | 308 +++++++++++++++++++++++++++++++++++++++
3 files changed, 318 insertions(+)
create mode 100644 drivers/usb/phy/phy-hi6220-usb.c
diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
index c6d0c8e..405a3d0 100644
--- a/drivers/usb/phy/Kconfig
+++ b/drivers/usb/phy/Kconfig
@@ -173,6 +173,15 @@ config USB_MXS_PHY
MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
+config USB_HI6220_PHY
+ tristate "hi6220 USB PHY support"
+ select USB_PHY
+ select MFD_SYSCON
+ help
+ Enable this to support the HISILICON HI6220 USB PHY.
+
+ To compile this driver as a module, choose M here.
+
config USB_RCAR_PHY
tristate "Renesas R-Car USB PHY support"
depends on USB || USB_GADGET
diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
index 75f2bba..00172d3 100644
--- a/drivers/usb/phy/Makefile
+++ b/drivers/usb/phy/Makefile
@@ -18,6 +18,7 @@ obj-$(CONFIG_SAMSUNG_USBPHY) += phy-samsung-usb.o
obj-$(CONFIG_TWL6030_USB) += phy-twl6030-usb.o
obj-$(CONFIG_USB_EHCI_TEGRA) += phy-tegra-usb.o
obj-$(CONFIG_USB_GPIO_VBUS) += phy-gpio-vbus-usb.o
+obj-$(CONFIG_USB_HI6220_PHY) += phy-hi6220-usb.o
obj-$(CONFIG_USB_ISP1301) += phy-isp1301.o
obj-$(CONFIG_USB_MSM_OTG) += phy-msm-usb.o
obj-$(CONFIG_USB_MV_OTG) += phy-mv-usb.o
diff --git a/drivers/usb/phy/phy-hi6220-usb.c b/drivers/usb/phy/phy-hi6220-usb.c
new file mode 100644
index 0000000..b251e85
--- /dev/null
+++ b/drivers/usb/phy/phy-hi6220-usb.c
@@ -0,0 +1,308 @@
+/*
+ * Copyright (c) 2015 Linaro Ltd.
+ * Copyright (c) 2015 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/mfd/syscon.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/usb/gadget.h>
+#include <linux/usb/otg.h>
+
+#define SC_PERIPH_CTRL4 0x00c
+
+#define CTRL4_PICO_SIDDQ BIT(6)
+#define CTRL4_PICO_OGDISABLE BIT(8)
+#define CTRL4_PICO_VBUSVLDEXT BIT(10)
+#define CTRL4_PICO_VBUSVLDEXTSEL BIT(11)
+#define CTRL4_OTG_PHY_SEL BIT(21)
+
+#define SC_PERIPH_CTRL5 0x010
+
+#define CTRL5_USBOTG_RES_SEL BIT(3)
+#define CTRL5_PICOPHY_ACAENB BIT(4)
+#define CTRL5_PICOPHY_BC_MODE BIT(5)
+#define CTRL5_PICOPHY_CHRGSEL BIT(6)
+#define CTRL5_PICOPHY_VDATSRCEND BIT(7)
+#define CTRL5_PICOPHY_VDATDETENB BIT(8)
+#define CTRL5_PICOPHY_DCDENB BIT(9)
+#define CTRL5_PICOPHY_IDDIG BIT(10)
+
+#define SC_PERIPH_CTRL8 0x018
+#define SC_PERIPH_RSTEN0 0x300
+#define SC_PERIPH_RSTDIS0 0x304
+
+#define RST0_USBOTG_BUS BIT(4)
+#define RST0_POR_PICOPHY BIT(5)
+#define RST0_USBOTG BIT(6)
+#define RST0_USBOTG_32K BIT(7)
+
+#define EYE_PATTERN_PARA 0x7053348c
+
+struct hi6220_priv {
+ struct usb_phy phy;
+ struct delayed_work work;
+ struct regmap *reg;
+ struct clk *clk;
+ struct regulator *vcc;
+ struct device *dev;
+ int gpio_vbus;
+ int gpio_id;
+ enum usb_otg_state state;
+};
+
+static void hi6220_start_periphrals(struct hi6220_priv *priv, bool on)
+{
+ struct usb_otg *otg = priv->phy.otg;
+
+ if (!otg->gadget)
+ return;
+
+ if (on)
+ usb_gadget_connect(otg->gadget);
+ else
+ usb_gadget_disconnect(otg->gadget);
+}
+
+static void hi6220_detect_work(struct work_struct *work)
+{
+ struct hi6220_priv *priv =
+ container_of(work, struct hi6220_priv, work.work);
+ int gpio_id, gpio_vbus;
+ enum usb_otg_state state;
+
+ if (!gpio_is_valid(priv->gpio_id) || !gpio_is_valid(priv->gpio_vbus))
+ return;
+
+ gpio_id = gpio_get_value_cansleep(priv->gpio_id);
+ gpio_vbus = gpio_get_value_cansleep(priv->gpio_vbus);
+
+ if (gpio_vbus == 0) {
+ if (gpio_id == 1)
+ state = OTG_STATE_B_PERIPHERAL;
+ else
+ state = OTG_STATE_A_HOST;
+ } else {
+ state = OTG_STATE_A_HOST;
+ }
+
+ if (priv->state != state) {
+ hi6220_start_periphrals(priv, state == OTG_STATE_B_PERIPHERAL);
+ priv->state = state;
+ }
+}
+
+static irqreturn_t hiusb_gpio_intr(int irq, void *data)
+{
+ struct hi6220_priv *priv = (struct hi6220_priv *)data;
+
+ /* add debounce time */
+ schedule_delayed_work(&priv->work, msecs_to_jiffies(100));
+ return IRQ_HANDLED;
+}
+
+static int hi6220_set_peripheral(struct usb_otg *otg, struct usb_gadget *gadget)
+{
+ otg->gadget = gadget;
+ return 0;
+}
+
+static int hi6220_phy_setup(struct hi6220_priv *priv, bool on)
+{
+ struct regmap *reg = priv->reg;
+ u32 val, mask;
+ int ret;
+
+ if (priv->reg == NULL)
+ return 0;
+
+ if (on) {
+ val = RST0_USBOTG_BUS | RST0_POR_PICOPHY |
+ RST0_USBOTG | RST0_USBOTG_32K;
+ mask = val;
+ ret = regmap_update_bits(reg, SC_PERIPH_RSTDIS0, mask, val);
+ if (ret)
+ goto out;
+
+ ret = regmap_read(reg, SC_PERIPH_CTRL5, &val);
+ val = CTRL5_USBOTG_RES_SEL | CTRL5_PICOPHY_ACAENB;
+ mask = val | CTRL5_PICOPHY_BC_MODE;
+ ret = regmap_update_bits(reg, SC_PERIPH_CTRL5, mask, val);
+ if (ret)
+ goto out;
+
+ val = CTRL4_PICO_VBUSVLDEXT | CTRL4_PICO_VBUSVLDEXTSEL |
+ CTRL4_OTG_PHY_SEL;
+ mask = val | CTRL4_PICO_SIDDQ | CTRL4_PICO_OGDISABLE;
+ ret = regmap_update_bits(reg, SC_PERIPH_CTRL4, mask, val);
+ if (ret)
+ goto out;
+
+ ret = regmap_write(reg, SC_PERIPH_CTRL8, EYE_PATTERN_PARA);
+ if (ret)
+ goto out;
+ } else {
+ val = CTRL4_PICO_SIDDQ;
+ mask = val;
+ ret = regmap_update_bits(reg, SC_PERIPH_CTRL4, mask, val);
+ if (ret)
+ goto out;
+
+ ret = regmap_read(reg, SC_PERIPH_CTRL4, &val);
+ val = RST0_USBOTG_BUS | RST0_POR_PICOPHY |
+ RST0_USBOTG | RST0_USBOTG_32K;
+ mask = val;
+ ret = regmap_update_bits(reg, SC_PERIPH_RSTEN0, mask, val);
+ if (ret)
+ goto out;
+ }
+
+ return 0;
+out:
+ dev_err(priv->dev, "failed to setup phy ret: %d\n", ret);
+ return ret;
+}
+
+static int hi6220_phy_probe(struct platform_device *pdev)
+{
+ struct hi6220_priv *priv;
+ struct usb_otg *otg;
+ struct device_node *np = pdev->dev.of_node;
+ struct device *dev = &pdev->dev;
+ int ret, irq;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ otg = devm_kzalloc(dev, sizeof(*otg), GFP_KERNEL);
+ if (!otg)
+ return -ENOMEM;
+
+ priv->dev = dev;
+ priv->phy.dev = &pdev->dev;
+ priv->phy.otg = otg;
+ priv->phy.label = "hi6220";
+ priv->phy.type = USB_PHY_TYPE_USB2;
+ otg->set_peripheral = hi6220_set_peripheral;
+ platform_set_drvdata(pdev, priv);
+
+ priv->gpio_vbus = of_get_named_gpio(np, "hisilicon,gpio-vbus", 0);
+ if (priv->gpio_vbus == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+ if (!gpio_is_valid(priv->gpio_vbus)) {
+ dev_err(dev, "invalid gpio %d\n", priv->gpio_vbus);
+ return -ENODEV;
+ }
+
+ priv->gpio_id = of_get_named_gpio(np, "hisilicon,gpio-id", 0);
+ if (priv->gpio_id == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+ if (!gpio_is_valid(priv->gpio_id)) {
+ dev_err(dev, "invalid gpio %d\n", priv->gpio_id);
+ return -ENODEV;
+ }
+
+ priv->reg = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
+ "hisilicon,peripheral-syscon");
+ if (IS_ERR(priv->reg))
+ priv->reg = NULL;
+
+ ret = devm_gpio_request_one(dev, priv->gpio_vbus,
+ GPIOF_IN, "gpio_vbus");
+ if (ret < 0) {
+ dev_err(dev, "gpio request failed for gpio_vbus\n");
+ return ret;
+ }
+
+ ret = devm_gpio_request_one(dev, priv->gpio_id, GPIOF_IN, "gpio_id");
+ if (ret < 0) {
+ dev_err(dev, "gpio request failed for gpio_id\n");
+ return ret;
+ }
+
+ priv->vcc = devm_regulator_get(dev, "vcc");
+ if (IS_ERR(priv->vcc)) {
+ if (PTR_ERR(priv->vcc) == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+ dev_info(dev, "No regulator found\n");
+ } else {
+ ret = regulator_enable(priv->vcc);
+ if (ret) {
+ dev_err(dev, "Failed to enable regulator\n");
+ return -ENODEV;
+ }
+ }
+
+ priv->clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(priv->clk)) {
+ regulator_disable(priv->vcc);
+ return PTR_ERR(priv->clk);
+ }
+ clk_prepare_enable(priv->clk);
+ INIT_DELAYED_WORK(&priv->work, hi6220_detect_work);
+
+ irq = gpio_to_irq(priv->gpio_vbus);
+ ret = devm_request_irq(dev, gpio_to_irq(priv->gpio_vbus),
+ hiusb_gpio_intr, IRQF_NO_SUSPEND |
+ IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
+ "vbus_gpio_intr", priv);
+ if (ret) {
+ dev_err(dev, "request gpio irq failed.\n");
+ goto err_irq;
+ }
+
+ hi6220_phy_setup(priv, true);
+ ret = usb_add_phy_dev(&priv->phy);
+ if (ret) {
+ dev_err(dev, "Can't register transceiver\n");
+ goto err_irq;
+ }
+ schedule_delayed_work(&priv->work, 0);
+
+ return 0;
+err_irq:
+ cancel_delayed_work_sync(&priv->work);
+ clk_disable_unprepare(priv->clk);
+ regulator_disable(priv->vcc);
+ return ret;
+}
+
+static int hi6220_phy_remove(struct platform_device *pdev)
+{
+ struct hi6220_priv *priv = platform_get_drvdata(pdev);
+
+ cancel_delayed_work_sync(&priv->work);
+ hi6220_phy_setup(priv, false);
+ clk_disable_unprepare(priv->clk);
+ regulator_disable(priv->vcc);
+ return 0;
+}
+
+static const struct of_device_id hi6220_phy_of_match[] = {
+ {.compatible = "hisilicon,hi6220-usb-phy",},
+ { },
+};
+MODULE_DEVICE_TABLE(of, hi6220_phy_of_match);
+
+static struct platform_driver hi6220_phy_driver = {
+ .probe = hi6220_phy_probe,
+ .remove = hi6220_phy_remove,
+ .driver = {
+ .name = "hi6220-usb-phy",
+ .of_match_table = hi6220_phy_of_match,
+ }
+};
+module_platform_driver(hi6220_phy_driver);
+
+MODULE_DESCRIPTION("HISILICON HI6220 USB PHY driver");
+MODULE_ALIAS("platform:hi6220-usb-phy");
+MODULE_LICENSE("GPL");
--
1.9.1
More information about the linux-arm-kernel
mailing list