[PATCH v3 2/2] ARM: at91: dts: sama5d4: add dts for sama5d4 xplained board

Josh Wu josh.wu at atmel.com
Mon Feb 9 19:24:30 PST 2015


Add at91 sama5d4 xplained board support.

Signed-off-by: Josh Wu <josh.wu at atmel.com>
---

Changes in v3:
- add phy0 child node under macb0
- rebase on top of linux next, re-formated the arch/arm/boot/dts/Makefile

Changes in v2:
- to be sorted by memory address, put the adc dt node after usart4.

 arch/arm/boot/dts/Makefile                  |   3 +-
 arch/arm/boot/dts/at91-sama5d4_xplained.dts | 238 ++++++++++++++++++++++++++++
 2 files changed, 240 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/at91-sama5d4_xplained.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index a1c776b..5c189a5 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -42,7 +42,8 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
 	sama5d34ek.dtb \
 	sama5d35ek.dtb \
 	sama5d36ek.dtb \
-	at91-sama5d4ek.dtb
+	at91-sama5d4ek.dtb \
+	at91-sama5d4_xplained.dtb
 dtb-$(CONFIG_ARCH_ATLAS6) += \
 	atlas6-evb.dtb
 dtb-$(CONFIG_ARCH_ATLAS7) += \
diff --git a/arch/arm/boot/dts/at91-sama5d4_xplained.dts b/arch/arm/boot/dts/at91-sama5d4_xplained.dts
new file mode 100644
index 0000000..9464e4a
--- /dev/null
+++ b/arch/arm/boot/dts/at91-sama5d4_xplained.dts
@@ -0,0 +1,238 @@
+/*
+ * at91-sama5d4_xplained.dts - Device Tree file for SAMA5D4 Xplained board
+ *
+ *  Copyright (C) 2015 Atmel,
+ *                2015 Josh Wu <josh.wu at atmel.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "sama5d4.dtsi"
+
+/ {
+	model = "Atmel SAMA5D4 Xplained";
+	compatible = "atmel,sama5d4-xplained", "atmel,sama5d4", "atmel,sama5";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 ignore_loglevel earlyprintk";
+	};
+
+	memory {
+		reg = <0x20000000 0x20000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		main_clock: clock at 0 {
+			compatible = "atmel,osc", "fixed-clock";
+			clock-frequency = <12000000>;
+		};
+
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		apb {
+			spi0: spi at f8010000 {
+				cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
+				status = "okay";
+				m25p80 at 0 {
+					compatible = "atmel,at25df321a";
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+				};
+			};
+
+			macb0: ethernet at f8020000 {
+				phy-mode = "rmii";
+				status = "okay";
+
+				phy0: ethernet-phy at 1 {
+					interrupt-parent = <&pioE>;
+					interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+					reg = <1>;
+				};
+			};
+
+			mmc1: mmc at fc000000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+				status = "okay";
+				slot at 0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioE 3 0>;
+				};
+			};
+
+			usart3: serial at fc00c000 {
+				status = "okay";
+			};
+
+			usart4: serial at fc010000 {
+				status = "okay";
+			};
+
+			adc0: adc at fc034000 {
+				atmel,adc-vref = <3300>;
+				status = "okay";
+			};
+
+			watchdog at fc068640 {
+				status = "okay";
+			};
+
+			pinctrl at fc06a000 {
+				board {
+					pinctrl_mmc1_cd: mmc1_cd {
+						atmel,pins =
+							<AT91_PIOE 3 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+					};
+					pinctrl_usba_vbus: usba_vbus {
+						atmel,pins =
+							<AT91_PIOE 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+					};
+					pinctrl_key_gpio: key_gpio_0 {
+						atmel,pins =
+							<AT91_PIOE 8 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PE13 gpio */
+					};
+				};
+			};
+		};
+
+		usb0: gadget at 00400000 {
+			atmel,vbus-gpio = <&pioE 31 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usba_vbus>;
+			status = "okay";
+		};
+
+		usb1: ohci at 00500000 {
+			num-ports = <3>;
+			atmel,vbus-gpio = <0
+					   &pioE 11 GPIO_ACTIVE_HIGH
+					   &pioE 14 GPIO_ACTIVE_HIGH
+					  >;
+			status = "okay";
+		};
+
+		usb2: ehci at 00600000 {
+			status = "okay";
+		};
+
+		nand0: nand at 80000000 {
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			nand-on-flash-bbt;
+			atmel,has-pmecc;
+			status = "okay";
+
+			at91bootstrap at 0 {
+				label = "at91bootstrap";
+				reg = <0x0 0x40000>;
+			};
+
+			bootloader at 40000 {
+				label = "bootloader";
+				reg = <0x40000 0x80000>;
+			};
+
+			bootloaderenv at c0000 {
+				label = "bootloader env";
+				reg = <0xc0000 0xc0000>;
+			};
+
+			dtb at 180000 {
+				label = "device tree";
+				reg = <0x180000 0x80000>;
+			};
+
+			kernel at 200000 {
+				label = "kernel";
+				reg = <0x200000 0x600000>;
+			};
+
+			rootfs at 800000 {
+				label = "rootfs";
+				reg = <0x800000 0x0f800000>;
+			};
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio>;
+
+		pb_user1 {
+			label = "pb_user1";
+			gpios = <&pioE 8 GPIO_ACTIVE_HIGH>;
+			linux,code = <0x100>;
+			gpio-key,wakeup;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		status = "okay";
+
+		d8 {
+			label = "d8";
+			gpios = <&pioE 15 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		d10 {
+			label = "d10";
+			gpios = <&pioD 30 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
-- 
1.9.1




More information about the linux-arm-kernel mailing list