[PATCH v3 3/4] serial: at91: Use helpers for gpio irqs
Janusz Uzycki
j.uzycki at elproma.com.pl
Fri Feb 6 08:55:34 PST 2015
The patch updates atmel_serial driver to use new mctrl_gpio helpers for
gpio irqs. The code is simpler now.
Signed-off-by: Janusz Uzycki <j.uzycki at elproma.com.pl>
---
There is no changes since v2.
---
drivers/tty/serial/atmel_serial.c | 123 +++++++-------------------------------
1 file changed, 20 insertions(+), 103 deletions(-)
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 846552b..6bcb181 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -168,7 +168,6 @@ struct atmel_uart_port {
struct circ_buf rx_ring;
struct mctrl_gpios *gpios;
- int gpio_irq[UART_GPIO_MAX];
unsigned int tx_done_mask;
bool ms_irq_enabled;
bool is_usart; /* usart or uart */
@@ -512,24 +511,18 @@ static void atmel_enable_ms(struct uart_port *port)
atmel_port->ms_irq_enabled = true;
- if (atmel_port->gpio_irq[UART_GPIO_CTS] >= 0)
- enable_irq(atmel_port->gpio_irq[UART_GPIO_CTS]);
- else
+ mctrl_gpio_enable_ms(atmel_port->gpios);
+
+ if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_CTS))
ier |= ATMEL_US_CTSIC;
- if (atmel_port->gpio_irq[UART_GPIO_DSR] >= 0)
- enable_irq(atmel_port->gpio_irq[UART_GPIO_DSR]);
- else
+ if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_DSR))
ier |= ATMEL_US_DSRIC;
- if (atmel_port->gpio_irq[UART_GPIO_RI] >= 0)
- enable_irq(atmel_port->gpio_irq[UART_GPIO_RI]);
- else
+ if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_RI))
ier |= ATMEL_US_RIIC;
- if (atmel_port->gpio_irq[UART_GPIO_DCD] >= 0)
- enable_irq(atmel_port->gpio_irq[UART_GPIO_DCD]);
- else
+ if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_DCD))
ier |= ATMEL_US_DCDIC;
UART_PUT_IER(port, ier);
@@ -551,24 +544,18 @@ static void atmel_disable_ms(struct uart_port *port)
atmel_port->ms_irq_enabled = false;
- if (atmel_port->gpio_irq[UART_GPIO_CTS] >= 0)
- disable_irq(atmel_port->gpio_irq[UART_GPIO_CTS]);
- else
+ mctrl_gpio_disable_ms(atmel_port->gpios);
+
+ if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_CTS))
idr |= ATMEL_US_CTSIC;
- if (atmel_port->gpio_irq[UART_GPIO_DSR] >= 0)
- disable_irq(atmel_port->gpio_irq[UART_GPIO_DSR]);
- else
+ if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_DSR))
idr |= ATMEL_US_DSRIC;
- if (atmel_port->gpio_irq[UART_GPIO_RI] >= 0)
- disable_irq(atmel_port->gpio_irq[UART_GPIO_RI]);
- else
+ if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_RI))
idr |= ATMEL_US_RIIC;
- if (atmel_port->gpio_irq[UART_GPIO_DCD] >= 0)
- disable_irq(atmel_port->gpio_irq[UART_GPIO_DCD]);
- else
+ if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_DCD))
idr |= ATMEL_US_DCDIC;
UART_PUT_IDR(port, idr);
@@ -1178,31 +1165,11 @@ atmel_handle_status(struct uart_port *port, unsigned int pending,
static irqreturn_t atmel_interrupt(int irq, void *dev_id)
{
struct uart_port *port = dev_id;
- struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
unsigned int status, pending, pass_counter = 0;
- bool gpio_handled = false;
do {
status = atmel_get_lines_status(port);
pending = status & UART_GET_IMR(port);
- if (!gpio_handled) {
- /*
- * Dealing with GPIO interrupt
- */
- if (irq == atmel_port->gpio_irq[UART_GPIO_CTS])
- pending |= ATMEL_US_CTSIC;
-
- if (irq == atmel_port->gpio_irq[UART_GPIO_DSR])
- pending |= ATMEL_US_DSRIC;
-
- if (irq == atmel_port->gpio_irq[UART_GPIO_RI])
- pending |= ATMEL_US_RIIC;
-
- if (irq == atmel_port->gpio_irq[UART_GPIO_DCD])
- pending |= ATMEL_US_DCDIC;
-
- gpio_handled = true;
- }
if (!pending)
break;
@@ -1682,45 +1649,6 @@ static void atmel_get_ip_name(struct uart_port *port)
}
}
-static void atmel_free_gpio_irq(struct uart_port *port)
-{
- struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
- enum mctrl_gpio_idx i;
-
- for (i = 0; i < UART_GPIO_MAX; i++)
- if (atmel_port->gpio_irq[i] >= 0)
- free_irq(atmel_port->gpio_irq[i], port);
-}
-
-static int atmel_request_gpio_irq(struct uart_port *port)
-{
- struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
- int *irq = atmel_port->gpio_irq;
- enum mctrl_gpio_idx i;
- int err = 0;
-
- for (i = 0; (i < UART_GPIO_MAX) && !err; i++) {
- if (irq[i] < 0)
- continue;
-
- irq_set_status_flags(irq[i], IRQ_NOAUTOEN);
- err = request_irq(irq[i], atmel_interrupt, IRQ_TYPE_EDGE_BOTH,
- "atmel_serial", port);
- if (err)
- dev_err(port->dev, "atmel_startup - Can't get %d irq\n",
- irq[i]);
- }
-
- /*
- * If something went wrong, rollback.
- */
- while (err && (--i >= 0))
- if (irq[i] >= 0)
- free_irq(irq[i], port);
-
- return err;
-}
-
/*
* Perform initialization and enable port for reception
*/
@@ -1752,7 +1680,7 @@ static int atmel_startup(struct uart_port *port)
/*
* Get the GPIO lines IRQ
*/
- retval = atmel_request_gpio_irq(port);
+ retval = mctrl_gpio_request_irqs(atmel_port->gpios);
if (retval)
goto free_irq;
@@ -1889,7 +1817,7 @@ static void atmel_shutdown(struct uart_port *port)
* Free the interrupts
*/
free_irq(port->irq, port);
- atmel_free_gpio_irq(port);
+ mctrl_gpio_free_irqs(atmel_port->gpios);
atmel_port->ms_irq_enabled = false;
@@ -2536,24 +2464,13 @@ static int atmel_serial_resume(struct platform_device *pdev)
#define atmel_serial_resume NULL
#endif
-static int atmel_init_gpios(struct atmel_uart_port *p, struct device *dev)
+static bool atmel_init_gpios(struct atmel_uart_port *p)
{
- enum mctrl_gpio_idx i;
- struct gpio_desc *gpiod;
-
- p->gpios = mctrl_gpio_init(dev, 0);
+ p->gpios = mctrl_gpio_init_dt(&p->uart, 0);
if (IS_ERR_OR_NULL(p->gpios))
- return -1;
+ return false;
- for (i = 0; i < UART_GPIO_MAX; i++) {
- gpiod = mctrl_gpio_to_gpiod(p->gpios, i);
- if (gpiod && (gpiod_get_direction(gpiod) == GPIOF_DIR_IN))
- p->gpio_irq[i] = gpiod_to_irq(gpiod);
- else
- p->gpio_irq[i] = -EINVAL;
- }
-
- return 0;
+ return true;
}
static int atmel_serial_probe(struct platform_device *pdev)
@@ -2593,8 +2510,8 @@ static int atmel_serial_probe(struct platform_device *pdev)
port->backup_imr = 0;
port->uart.line = ret;
- ret = atmel_init_gpios(port, &pdev->dev);
- if (ret < 0)
+ port->uart.dev = &pdev->dev;
+ if (!atmel_init_gpios(port))
dev_err(&pdev->dev, "%s",
"Failed to initialize GPIOs. The serial port may not work as expected");
--
1.7.11.3
More information about the linux-arm-kernel
mailing list