[PATCH v3 0/5] Introducing the Alpine platform.

[Maxime Coquelin]

Hi Tsahee,
On 02/02/2015 12:20 PM, Tsahee Zidenberg wrote:
> Annapurna Labs(TM) is a technology company providing innovative solutions
> including chips, software, and systems for the datacenter and enterprise
> infrastructure.
>
> Alpine(TM) is one of Annapurna Labs’ chip products targeting storage and
> networking applications. It is a complete Platform-On-Chip,
> integrating 2-4 cortex-A15 cores and multiple innovations to provide
> a seamless networking and storage fabric for enterprise and datacenter
> equipment.
>
> This patchset provides initial support for the Alpine platform.
>
> Patch #1 contains minimal, single-cpu architecture support.
>
> Patch #2 adds early-debug capabilities via Alpine UART 0.
>
> Patch #3 adds smp-support and a secondary cpu enable-method for the platform.
>
> Patch #4 provides documentation for the available device-tree nodes.
>
> Patch #5 provides a device-tree for Alpine soc and development board.
>
> The patchset was tested with multi_v7_defconfig, adding CONFIG_ARCH_ALPINE
>
> ---
> V2:
> * map physical cpu-id from logical on cpu wakeup
> * use syscon/regmap for sysfabric_service implementation
> * devicetree format:
> **  split between .dtsi and dts
> **  dual license
> **  node and manufacturer naming
> * intoduce devicetree in two separate patches
> * multiple format fixes
> * rebased on d932006 (for-next)
>
> ---
> V3:
> * small format changes
> * rebased on f9db7e2 (for-next)
>
> Tsahee Zidenberg (5):
>    ARM: Alpine: Initial support for Alpine platform
>    ARM: Alpine: early-debug print support
>    ARM: Alpine: smp support
>    ARM: dts: Alpine platform binding documentation
>    ARM: dts: Alpine platform devicetree
>
>   .../devicetree/bindings/arm/al,alpine.txt          |  88 +++++++++++++
>   .../bindings/arm/cpu-enable-method/al,alpine-smp   |  52 ++++++++
>   .../devicetree/bindings/vendor-prefixes.txt        |   1 +
>   arch/arm/Kconfig                                   |   2 +
>   arch/arm/Kconfig.debug                             |  12 +-
>   arch/arm/Makefile                                  |   1 +
>   arch/arm/boot/dts/Makefile                         |   4 +
>   arch/arm/boot/dts/alpine-db.dts                    |  35 +++++
>   arch/arm/boot/dts/alpine.dtsi                      | 141 +++++++++++++++++++++
>   arch/arm/mach-alpine/Kconfig                       |  10 ++
>   arch/arm/mach-alpine/Makefile                      |   6 +
>   arch/arm/mach-alpine/alpine_cpu_pm.c               |  70 ++++++++++
>   arch/arm/mach-alpine/alpine_cpu_pm.h               |  26 ++++
>   arch/arm/mach-alpine/alpine_cpu_resume.h           |  38 ++++++
>   arch/arm/mach-alpine/alpine_machine.c              |  28 ++++
>   arch/arm/mach-alpine/platsmp.c                     |  49 +++++++
>   16 files changed, 562 insertions(+), 1 deletion(-)
>   create mode 100644 Documentation/devicetree/bindings/arm/al,alpine.txt
>   create mode 100644 Documentation/devicetree/bindings/arm/cpu-enable-method/al,alpine-smp
>   create mode 100644 arch/arm/boot/dts/alpine-db.dts
>   create mode 100644 arch/arm/boot/dts/alpine.dtsi
>   create mode 100644 arch/arm/mach-alpine/Kconfig
>   create mode 100644 arch/arm/mach-alpine/Makefile
>   create mode 100644 arch/arm/mach-alpine/alpine_cpu_pm.c
>   create mode 100644 arch/arm/mach-alpine/alpine_cpu_pm.h
>   create mode 100644 arch/arm/mach-alpine/alpine_cpu_resume.h
>   create mode 100644 arch/arm/mach-alpine/alpine_machine.c
>   create mode 100644 arch/arm/mach-alpine/platsmp.c
>
You need to add an entry in the MAINTAINERS file, so that 
get_maintainers.pl script
adds the right guys for patch impacting your machine.

Br,
Maxime