[PATCH 27/30] ARM: sun7i: olinuxino lime2: Convert to DT label based syntax
Maxime Ripard
maxime.ripard at free-electrons.com
Sun Feb 1 05:50:11 PST 2015
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard at free-electrons.com>
---
arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts | 288 ++++++++++++------------
1 file changed, 143 insertions(+), 145 deletions(-)
diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
index 260dbd3bf29d..5e57157f742d 100644
--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
+++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
@@ -57,176 +57,174 @@
model = "Olimex A20-OLinuXino-LIME2";
compatible = "olimex,a20-olinuxino-lime2", "allwinner,sun7i-a20";
- soc at 01c00000 {
- mmc0: mmc at 01c0f000 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
- vmmc-supply = <®_vcc3v3>;
- bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
- status = "okay";
- };
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_olinuxinolime>;
- usbphy: phy at 01c13400 {
- usb1_vbus-supply = <®_usb1_vbus>;
- usb2_vbus-supply = <®_usb2_vbus>;
- status = "okay";
+ green {
+ label = "a20-olinuxino-lime2:green:usr";
+ gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
};
+ };
- ehci0: usb at 01c14000 {
- status = "okay";
- };
+ reg_axp_ipsout: axp_ipsout {
+ compatible = "regulator-fixed";
+ regulator-name = "axp-ipsout";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+};
- ohci0: usb at 01c14400 {
- status = "okay";
- };
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
- ahci: sata at 01c18000 {
- target-supply = <®_ahci_5v>;
- status = "okay";
- };
+&ehci0 {
+ status = "okay";
+};
- ehci1: usb at 01c1c000 {
- status = "okay";
- };
+&ehci1 {
+ status = "okay";
+};
- ohci1: usb at 01c1c400 {
- status = "okay";
- };
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ status = "okay";
- pinctrl at 01c20800 {
- ahci_pwr_pin_olinuxinolime: ahci_pwr_pin at 1 {
- allwinner,pins = "PC3";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
+ phy1: ethernet-phy at 1 {
+ reg = <1>;
+ };
+};
- led_pins_olinuxinolime: led_pins at 0 {
- allwinner,pins = "PH2";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_20_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic at 34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ acin-supply = <®_axp_ipsout>;
+ vin2-supply = <®_axp_ipsout>;
+ vin3-supply = <®_axp_ipsout>;
+ ldo24in-supply = <®_axp_ipsout>;
+ ldo3in-supply = <®_axp_ipsout>;
+
+ regulators {
+ vdd_rtc: ldo1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
};
- };
- uart0: serial at 01c28000 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
- status = "okay";
- };
+ avcc: ldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
- i2c0: i2c at 01c2ac00 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-
- axp209: pmic at 34 {
- compatible = "x-powers,axp209";
- reg = <0x34>;
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-
- interrupt-controller;
- #interrupt-cells = <1>;
-
- acin-supply = <®_axp_ipsout>;
- vin2-supply = <®_axp_ipsout>;
- vin3-supply = <®_axp_ipsout>;
- ldo24in-supply = <®_axp_ipsout>;
- ldo3in-supply = <®_axp_ipsout>;
-
- regulators {
- vdd_rtc: ldo1 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- regulator-always-on;
- };
-
- avcc: ldo2 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- vcc_csi0: ldo3 {
- regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <3500000>;
- regulator-always-on;
- };
-
- vcc_csi1: ldo4 {
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- vdd_cpu: dcdc2 {
- regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <2275000>;
- regulator-always-on;
- };
-
- vdd_int: dcdc3 {
- regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <3500000>;
- regulator-always-on;
- };
- };
+ vcc_csi0: ldo3 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <3500000>;
+ regulator-always-on;
};
- };
- i2c1: i2c at 01c2b000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "okay";
- };
+ vcc_csi1: ldo4 {
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
- gmac: ethernet at 01c50000 {
- pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
- phy = <&phy1>;
- phy-mode = "rgmii";
- status = "okay";
+ vdd_cpu: dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <2275000>;
+ regulator-always-on;
+ };
- phy1: ethernet-phy at 1 {
- reg = <1>;
+ vdd_int: dcdc3 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <3500000>;
+ regulator-always-on;
};
};
};
+};
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_olinuxinolime>;
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
- green {
- label = "a20-olinuxino-lime2:green:usr";
- gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>;
- default-state = "on";
- };
- };
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
- reg_ahci_5v: ahci-5v {
- pinctrl-0 = <&ahci_pwr_pin_olinuxinolime>;
- gpio = <&pio 2 3 GPIO_ACTIVE_HIGH>;
- status = "okay";
- };
+&ohci0 {
+ status = "okay";
+};
- reg_usb1_vbus: usb1-vbus {
- status = "okay";
- };
+&ohci1 {
+ status = "okay";
+};
- reg_usb2_vbus: usb2-vbus {
- status = "okay";
+&pio {
+ ahci_pwr_pin_olinuxinolime: ahci_pwr_pin at 1 {
+ allwinner,pins = "PC3";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- reg_axp_ipsout: axp_ipsout {
- compatible = "regulator-fixed";
- regulator-name = "axp-ipsout";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
+ led_pins_olinuxinolime: led_pins at 0 {
+ allwinner,pins = "PH2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
+
+®_ahci_5v {
+ pinctrl-0 = <&ahci_pwr_pin_olinuxinolime>;
+ gpio = <&pio 2 3 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--
2.2.2
More information about the linux-arm-kernel
mailing list