[PATCH 16/30] ARM: sun5i: a13: olinuxino: Convert to DT label based syntax

[Maxime Ripard]

In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax

Signed-off-by: Maxime Ripard <maxime.ripard at free-electrons.com>
---
 arch/arm/boot/dts/sun5i-a13-olinuxino.dts | 236 +++++++++++++++---------------
 1 file changed, 117 insertions(+), 119 deletions(-)

diff --git a/arch/arm/boot/dts/sun5i-a13-olinuxino.dts b/arch/arm/boot/dts/sun5i-a13-olinuxino.dts
index 6b24876ed462..d09c57b4905b 100644
--- a/arch/arm/boot/dts/sun5i-a13-olinuxino.dts
+++ b/arch/arm/boot/dts/sun5i-a13-olinuxino.dts
@@ -63,141 +63,139 @@
 		serial0 = &uart1;
 	};
 
-	soc at 01c00000 {
-		mmc0: mmc at 01c0f000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino>;
-			vmmc-supply = <&reg_vcc3v3>;
-			bus-width = <4>;
-			cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
-			cd-inverted;
-			status = "okay";
-		};
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_olinuxino>;
 
-		usbphy: phy at 01c13400 {
-			usb1_vbus-supply = <&reg_usb1_vbus>;
-			status = "okay";
+		power {
+			gpios = <&pio 6 9 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
 		};
+	};
+};
 
-		ehci0: usb at 01c14000 {
-			status = "okay";
-		};
+&ehci0 {
+	status = "okay";
+};
 
-		ohci0: usb at 01c14400 {
-			status = "okay";
-		};
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
 
-		pinctrl at 01c20800 {
-			mmc0_cd_pin_olinuxino: mmc0_cd_pin at 0 {
-				allwinner,pins = "PG0";
-				allwinner,function = "gpio_in";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-			};
-
-			led_pins_olinuxino: led_pins at 0 {
-				allwinner,pins = "PG9";
-				allwinner,function = "gpio_out";
-				allwinner,drive = <SUN4I_PINCTRL_20_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			usb1_vbus_pin_olinuxino: usb1_vbus_pin at 0 {
-				allwinner,pins = "PG11";
-				allwinner,function = "gpio_out";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-		};
+	axp209: pmic at 34 {
+		compatible = "x-powers,axp209";
+		reg = <0x34>;
+		interrupts = <0>;
 
-		lradc: lradc at 01c22800 {
-			vref-supply = <&reg_vcc3v0>;
-			status = "okay";
-
-			button at 191 {
-				label = "Volume Up";
-				linux,code = <KEY_VOLUMEUP>;
-				channel = <0>;
-				voltage = <191274>;
-			};
-
-			button at 392 {
-				label = "Volume Down";
-				linux,code = <KEY_VOLUMEDOWN>;
-				channel = <0>;
-				voltage = <392644>;
-			};
-
-			button at 601 {
-				label = "Menu";
-				linux,code = <KEY_MENU>;
-				channel = <0>;
-				voltage = <601151>;
-			};
-
-			button at 795 {
-				label = "Enter";
-				linux,code = <KEY_ENTER>;
-				channel = <0>;
-				voltage = <795090>;
-			};
-
-			button at 987 {
-				label = "Home";
-				linux,code = <KEY_HOMEPAGE>;
-				channel = <0>;
-				voltage = <987387>;
-			};
-		};
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+};
 
-		uart1: serial at 01c28400 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart1_pins_b>;
-			status = "okay";
-		};
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+};
 
-		i2c0: i2c at 01c2ac00 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c0_pins_a>;
-			status = "okay";
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	status = "okay";
+};
 
-			axp209: pmic at 34 {
-				compatible = "x-powers,axp209";
-				reg = <0x34>;
-				interrupts = <0>;
+&lradc {
+	vref-supply = <&reg_vcc3v0>;
+	status = "okay";
 
-				interrupt-controller;
-				#interrupt-cells = <1>;
-			};
-		};
+	button at 191 {
+		label = "Volume Up";
+		linux,code = <KEY_VOLUMEUP>;
+		channel = <0>;
+		voltage = <191274>;
+	};
 
-		i2c1: i2c at 01c2b000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c1_pins_a>;
-			status = "okay";
-		};
+	button at 392 {
+		label = "Volume Down";
+		linux,code = <KEY_VOLUMEDOWN>;
+		channel = <0>;
+		voltage = <392644>;
+	};
 
-		i2c2: i2c at 01c2b400 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c2_pins_a>;
-			status = "okay";
-		};
+	button at 601 {
+		label = "Menu";
+		linux,code = <KEY_MENU>;
+		channel = <0>;
+		voltage = <601151>;
 	};
 
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins_olinuxino>;
+	button at 795 {
+		label = "Enter";
+		linux,code = <KEY_ENTER>;
+		channel = <0>;
+		voltage = <795090>;
+	};
 
-		power {
-			gpios = <&pio 6 9 GPIO_ACTIVE_HIGH>;
-			default-state = "on";
-		};
+	button at 987 {
+		label = "Home";
+		linux,code = <KEY_HOMEPAGE>;
+		channel = <0>;
+		voltage = <987387>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
+	cd-inverted;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&pio {
+	mmc0_cd_pin_olinuxino: mmc0_cd_pin at 0 {
+		allwinner,pins = "PG0";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
+
+	led_pins_olinuxino: led_pins at 0 {
+		allwinner,pins = "PG9";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 	};
 
-	reg_usb1_vbus: usb1-vbus {
-		pinctrl-0 = <&usb1_vbus_pin_olinuxino>;
-		gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>;
-		status = "okay";
+	usb1_vbus_pin_olinuxino: usb1_vbus_pin at 0 {
+		allwinner,pins = "PG11";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 	};
 };
+
+&reg_usb1_vbus {
+	pinctrl-0 = <&usb1_vbus_pin_olinuxino>;
+	gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins_b>;
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
-- 
2.2.2