[PATCH v2 2/3] wlcore/wl12xx: spi: add device tree support

[Uri Mashiach]

Hello Javier,

On 12/24/2015 06:25 PM, Javier Martinez Canillas wrote:
> Hello Uri,
>
> On Thu, Dec 24, 2015 at 12:35 PM, Uri Mashiach
> <uri.mashiach at compulab.co.il> wrote:
>> Add DT support for the wl1271 SPI WiFi.
>>
>> Add documentation file for the wl1271 SPI WiFi.
>>
>> Signed-off-by: Uri Mashiach <uri.mashiach at compulab.co.il>
>> Acked-by: Igor Grinberg <grinberg at compulab.co.il>
>> ---
>> v1 -> v2: update interrupt documentation.
>>            replace interrupts and interrupt-parent with interrupts-extended.
>>            IRQ parameters retrieved from spi_device instead of DT.
>>            remove redundant #ifdef CONFIG_OF
>>
>>   .../bindings/net/wireless/ti,wlcore,spi.txt        | 34 +++++++++++++
>>   drivers/net/wireless/ti/wlcore/spi.c               | 55 ++++++++++++++++++++--
>>   2 files changed, 85 insertions(+), 4 deletions(-)
>>   create mode 100644 Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
>>
>> diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
>> new file mode 100644
>> index 0000000..502c27e
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
>> @@ -0,0 +1,34 @@
>> +* Texas Instruments wl1271 wireless lan controller
>> +
>> +The wl1271 chip can be connected via SPI or via SDIO. This
>> +document describes the binding for the SPI connected chip.
>> +
>> +Required properties:
>> +- compatible :          Should be "ti,wl1271"
>> +- reg :                 Chip select address of device
>> +- spi-max-frequency :   Maximum SPI clocking speed of device in Hz
>> +- ref-clock-frequency : Reference clock frequency
>> +- interrupts-extended : Should contain parameters for 1 interrupt line.
>> +                        Interrupt parameters: parent, line number, type.
>> +- vwlan-supply :        Point the node of the regulator that powers/enable the wl1271 chip
>> +
>> +Optional properties:
>> +- clock-xtal :          boolean, clock is generated from XTAL
>> +
>> +- Please consult Documentation/devicetree/bindings/spi/spi-bus.txt
>> +  for optional SPI connection related properties,
>> +
>> +Examples:
>> +
>> +&spi1 {
>> +       wl1271 at 1 {
>> +               compatible = "ti,wl1271";
>> +
>> +               reg = <1>;
>> +               spi-max-frequency = <48000000>;
>> +               clock-xtal;
>> +               ref-clock-frequency = <38400000>;
>> +               interrupts-extended = <&gpio3 8 IRQ_TYPE_LEVEL_HIGH>;
>> +               vwlan-supply = <&vwlan_fixed>;
>> +       };
>> +};
>> diff --git a/drivers/net/wireless/ti/wlcore/spi.c b/drivers/net/wireless/ti/wlcore/spi.c
>> index d3a4bcb..e9e8d54 100644
>> --- a/drivers/net/wireless/ti/wlcore/spi.c
>> +++ b/drivers/net/wireless/ti/wlcore/spi.c
>> @@ -30,6 +30,7 @@
>>   #include <linux/spi/spi.h>
>>   #include <linux/wl12xx.h>
>>   #include <linux/platform_device.h>
>> +#include <linux/of_irq.h>
>>   #include <linux/regulator/consumer.h>
>>
>>   #include "wlcore.h"
>> @@ -357,6 +358,46 @@ static struct wl1271_if_operations spi_ops = {
>>          .set_block_size = NULL,
>>   };
>>
>> +#ifdef CONFIG_OF
>> +static const struct of_device_id wlcore_spi_of_match_table[] = {
>> +       { .compatible = "ti,wl1271" },
>> +       { }
>> +};
>
> Could you please add a MODULE_DEVICE_TABLE(of, wlcore_spi_of_match_table) here?
>

Will be added in v3.

>> +
>> +/**
>> + * wlcore_probe_of - DT node parsing.
>> + * @spi: SPI slave device parameters.
>> + * @res: resource parameters.
>> + * @glue: wl12xx SPI bus to slave device glue parameters.
>> + * @pdev_data: wlcore device parameters
>> + */
>> +static int wlcore_probe_of(struct spi_device *spi, struct wl12xx_spi_glue *glue,
>> +                          struct wlcore_platdev_data *pdev_data)
>> +{
>> +       struct device_node *dt_node = spi->dev.of_node;
>> +       int ret;
>> +
>> +       if (of_find_property(dt_node, "clock-xtal", NULL))
>> +               pdev_data->ref_clock_xtal = true;
>> +
>> +       ret = of_property_read_u32(dt_node, "ref-clock-frequency",
>> +                                  &pdev_data->ref_clock_freq);
>> +       if (IS_ERR_VALUE(ret)) {
>> +               dev_err(glue->dev,
>> +                       "can't get reference clock frequency (%d)\n", ret);
>> +               return ret;
>> +       }
>> +
>> +       return 0;
>> +}
>> +#else /* CONFIG_OF */
>> +static int wlcore_probe_of(struct spi_device *spi, struct wl12xx_spi_glue *glue,
>> +                          struct wlcore_platdev_data *pdev_data)
>> +{
>> +       return -ENODATA;
>> +}
>> +#endif /* CONFIG_OF */
>> +
>
> I don't understand what's the point of making the driver to be built
> with !CONFIG_OF if the probe function is going to fail anyways. If
> this driver really need then is better to remove the ifdefery and make
> the Kconfig symbol to depend on OF.
>

Will be done in v3.

> Best regards,
> Javier
>

Thanks,
Uri