[PATCH v2 1/2] ARM: dts: imx7d: cl-som-imx7: add basic module support
Ilya Ledvich
ilya at compulab.co.il
Tue Dec 22 00:15:19 PST 2015
CL-SOM-iMX7 is a miniature System-on-Module (SoM) based on
Freescale i.MX7 System-on-Chip family.
http://www.compulab.co.il/products/computer-on-modules/cl-som-imx7-freescale-i-mx-7-system-on-module/
Add basic DT support for standalone module (without a carrier board):
* Memory configuration
* eMMC
* 2x Gigabit Ethernet ports (FEC1 and FEC2)
* I2C2 bus
* EEPROM
* PCA9555 GPIO extender
* PMIC
* UART1
* USB OTG port
Signed-off-by: Ilya Ledvich <ilya at compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg at compulab.co.il>
---
v2: use generic node name for pmic (Thanks Rob)
move board description out of fsl.txt (Shawn)
use GPL/X11 dual licence for newly added dts files (Shawn)
discard one level of container node (Shawn)
squash several patches into one patch (Shawn)
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx7d-cl-som-imx7.dts | 293 ++++++++++++++++++++++++++++++++
2 files changed, 294 insertions(+)
create mode 100644 arch/arm/boot/dts/imx7d-cl-som-imx7.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 30bbc37..83ed521 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -350,6 +350,7 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ul-14x14-evk.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
+ imx7d-cl-som-imx7.dtb \
imx7d-sdb.dtb
dtb-$(CONFIG_SOC_LS1021A) += \
ls1021a-qds.dtb \
diff --git a/arch/arm/boot/dts/imx7d-cl-som-imx7.dts b/arch/arm/boot/dts/imx7d-cl-som-imx7.dts
new file mode 100644
index 0000000..1ec4528
--- /dev/null
+++ b/arch/arm/boot/dts/imx7d-cl-som-imx7.dts
@@ -0,0 +1,293 @@
+/*
+ * Support for CompuLab CL-SOM-iMX7 System-on-Module
+ *
+ * Copyright (C) 2015 CompuLab Ltd. - http://www.compulab.co.il/
+ * Author: Ilya Ledvich <ilya at compulab.co.il>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "imx7d.dtsi"
+
+/ {
+ model = "CompuLab CL-SOM-iMX7";
+ compatible = "compulab,cl-som-imx7", "fsl,imx7d";
+
+ memory {
+ reg = <0x80000000 0x10000000>; /* 256 MB - minimal configuration */
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_usb_otg1_vbus: regulator at 0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+ };
+};
+
+&cpu0 {
+ arm-supply = <&sw1a_reg>;
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
+ <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
+ assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+ assigned-clock-rates = <0>, <100000000>;
+ phy-mode = "rgmii";
+ phy-handle = <ðphy0>;
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy at 0 {
+ reg = <0>;
+ };
+
+ ethphy1: ethernet-phy at 1 {
+ reg = <1>;
+ };
+ };
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>;
+ assigned-clocks = <&clks IMX7D_ENET2_TIME_ROOT_SRC>,
+ <&clks IMX7D_ENET2_TIME_ROOT_CLK>;
+ assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+ assigned-clock-rates = <0>, <100000000>;
+ phy-mode = "rgmii";
+ phy-handle = <ðphy1>;
+ fsl,magic-packet;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ pmic: pmic at 8 {
+ compatible = "fsl,pfuze3000";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1a {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1475000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ /* use sw1c_reg to align with pfuze100/pfuze200 */
+ sw1c_reg: sw1b {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1475000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1650000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen2_reg: vldo2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vccsd {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen4_reg: v33 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vldo3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vldo4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+
+ pca9555: pca9555 at 20 {
+ compatible = "nxp,pca9555";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x20>;
+ };
+
+ eeprom at 50 {
+ compatible = "atmel,24c08";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ assigned-clocks = <&clks IMX7D_UART1_ROOT_SRC>;
+ assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
+ status = "okay";
+};
+
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg1>;
+ vbus-supply = <®_usb_otg1_vbus>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>;
+ assigned-clock-rates = <400000000>;
+ bus-width = <8>;
+ fsl,tuning-step = <2>;
+ non-removable;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX7D_PAD_SD2_CD_B__ENET1_MDIO 0x3
+ MX7D_PAD_SD2_WP__ENET1_MDC 0x3
+ MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC 0x1
+ MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 0x1
+ MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 0x1
+ MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2 0x1
+ MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3 0x1
+ MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL 0x1
+ MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC 0x1
+ MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 0x1
+ MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 0x1
+ MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2 0x1
+ MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3 0x1
+ MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL 0x1
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC 0x1
+ MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0 0x1
+ MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1 0x1
+ MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2 0x1
+ MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3 0x1
+ MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL 0x1
+ MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC 0x1
+ MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0 0x1
+ MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1 0x1
+ MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2 0x1
+ MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3 0x1
+ MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL 0x1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX7D_PAD_I2C2_SDA__I2C2_SDA 0x4000007f
+ MX7D_PAD_I2C2_SCL__I2C2_SCL 0x4000007f
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX 0x79
+ MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX 0x79
+ >;
+ };
+
+ pinctrl_usbotg1: usbotg1grp {
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO05__GPIO1_IO5 0x14 /* OTG PWREN */
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX7D_PAD_SD3_CMD__SD3_CMD 0x59
+ MX7D_PAD_SD3_CLK__SD3_CLK 0x19
+ MX7D_PAD_SD3_DATA0__SD3_DATA0 0x59
+ MX7D_PAD_SD3_DATA1__SD3_DATA1 0x59
+ MX7D_PAD_SD3_DATA2__SD3_DATA2 0x59
+ MX7D_PAD_SD3_DATA3__SD3_DATA3 0x59
+ MX7D_PAD_SD3_DATA4__SD3_DATA4 0x59
+ MX7D_PAD_SD3_DATA5__SD3_DATA5 0x59
+ MX7D_PAD_SD3_DATA6__SD3_DATA6 0x59
+ MX7D_PAD_SD3_DATA7__SD3_DATA7 0x59
+ MX7D_PAD_SD3_STROBE__SD3_STROBE 0x19
+ >;
+ };
+};
--
1.9.1
More information about the linux-arm-kernel
mailing list