[PATCH 1/2] ARM: dts: ts-4800: Add LCD support

[Damien Riegel]

On Mon, Dec 21, 2015 at 09:35:19PM +0800, Shawn Guo wrote:
> On Fri, Dec 18, 2015 at 12:00:32PM -0500, Damien Riegel wrote:
> > This commit adds LCD support for the TS-4800. The panel is an Okaya
> > RS800480T-7X0WQ and the timings have been extracted from Technologic
> > Systems' tree.
> > 
> > Signed-off-by: Damien Riegel <damien.riegel at savoirfairelinux.com>
> > ---
> >  arch/arm/boot/dts/imx51-ts4800.dts | 109 +++++++++++++++++++++++++++++++++++++
> >  1 file changed, 109 insertions(+)
> > 
> > diff --git a/arch/arm/boot/dts/imx51-ts4800.dts b/arch/arm/boot/dts/imx51-ts4800.dts
> > index 83352cb..4951ebd 100644
> > --- a/arch/arm/boot/dts/imx51-ts4800.dts
> > +++ b/arch/arm/boot/dts/imx51-ts4800.dts
> > @@ -30,6 +30,60 @@
> >  			clock-frequency = <24576000>;
> >  		};
> >  	};
> > +
> > +	regulators {
> > +		compatible = "simple-bus";
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +
> > +		backlight_reg: regulator at 0 {
> > +			compatible = "regulator-fixed";
> > +			reg = <0>;
> > +			pinctrl-names = "default";
> > +			pinctrl-0 = <&pinctrl_enable_lcd>;
> > +			regulator-name = "enable_lcd_reg";
> > +			regulator-min-microvolt = <3300000>;
> > +			regulator-max-microvolt = <3300000>;
> > +			gpio = <&gpio4 9 GPIO_ACTIVE_HIGH>;
> > +			enable-active-high;
> > +		};
> > +	};
> 
> DT maintainers dislike this fake simple-bus container.  Let's put the
> regulator directly under root like below.
> 
>         backlight_reg: regulator-backlight {
>                 compatible = "regulator-fixed";
>                 pinctrl-names = "default";
>                 pinctrl-0 = <&pinctrl_enable_lcd>;
>                 regulator-name = "enable_lcd_reg";
>                 regulator-min-microvolt = <3300000>;
>                 regulator-max-microvolt = <3300000>;
>                 gpio = <&gpio4 9 GPIO_ACTIVE_HIGH>;
>                 enable-active-high;
>         };
> 
> I fixed it up and applied both patches.

Thank you. I am using the imx51-*.dts as examples, maybe they should be
updated to be consistent with the newer device tree style? I'm willing
to do that but I don't want to make changes on dts files that I can't
test.

Sidenote: your Signed-off-by is missing on these two patches.


Thanks,
Damien

> 
> Shawn
> 
> > +
> > +	backlight: backlight {
> > +		compatible = "pwm-backlight";
> > +		pwms = <&pwm1 0 78770>;
> > +		brightness-levels = <0 150 200 255>;
> > +		default-brightness-level = <1>;
> > +		power-supply = <&backlight_reg>;
> > +	};
> > +
> > +	display0: display at di0 {
> > +		compatible = "fsl,imx-parallel-display";
> > +		interface-pix-fmt = "rgb24";
> > +		pinctrl-names = "default";
> > +		pinctrl-0 = <&pinctrl_lcd>;
> > +
> > +		display-timings {
> > +			800x480p60 {
> > +				native-mode;
> > +				clock-frequency = <30066000>;
> > +				hactive = <800>;
> > +				vactive = <480>;
> > +				hfront-porch = <50>;
> > +				hback-porch = <70>;
> > +				hsync-len = <50>;
> > +				vback-porch = <0>;
> > +				vfront-porch = <0>;
> > +				vsync-len = <50>;
> > +			};
> > +		};
> > +
> > +		port at 0 {
> > +			display0_in: endpoint {
> > +				remote-endpoint = <&ipu_di0_disp0>;
> > +			};
> > +		};
> > +	};
> >  };
> >  
> >  &esdhc1 {
> > @@ -60,6 +114,16 @@
> >  	};
> >  };
> >  
> > +&ipu_di0_disp0 {
> > +	remote-endpoint = <&display0_in>;
> > +};
> > +
> > +&pwm1 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&pinctrl_pwm_backlight>;
> > +	status = "okay";
> > +};
> > +
> >  &uart1 {
> >  	pinctrl-names = "default";
> >  	pinctrl-0 = <&pinctrl_uart1>;
> > @@ -115,6 +179,12 @@
> >  		>;
> >  	};
> >  
> > +	pinctrl_enable_lcd: enablelcdgrp {
> > +		fsl,pins = <
> > +			MX51_PAD_CSI2_D12__GPIO4_9		0x1c5
> > +		>;
> > +	};
> > +
> >  	pinctrl_esdhc1: esdhc1grp {
> >  		fsl,pins = <
> >  			MX51_PAD_SD1_CMD__SD1_CMD		0x400020d5
> > @@ -159,6 +229,45 @@
> >  		>;
> >  	};
> >  
> > +	pinctrl_lcd: lcdgrp {
> > +		fsl,pins = <
> > +			MX51_PAD_DISP1_DAT0__DISP1_DAT0		0x5
> > +			MX51_PAD_DISP1_DAT1__DISP1_DAT1		0x5
> > +			MX51_PAD_DISP1_DAT2__DISP1_DAT2		0x5
> > +			MX51_PAD_DISP1_DAT3__DISP1_DAT3		0x5
> > +			MX51_PAD_DISP1_DAT4__DISP1_DAT4		0x5
> > +			MX51_PAD_DISP1_DAT5__DISP1_DAT5		0x5
> > +			MX51_PAD_DISP1_DAT6__DISP1_DAT6		0x5
> > +			MX51_PAD_DISP1_DAT7__DISP1_DAT7		0x5
> > +			MX51_PAD_DISP1_DAT8__DISP1_DAT8		0x5
> > +			MX51_PAD_DISP1_DAT9__DISP1_DAT9		0x5
> > +			MX51_PAD_DISP1_DAT10__DISP1_DAT10	0x5
> > +			MX51_PAD_DISP1_DAT11__DISP1_DAT11	0x5
> > +			MX51_PAD_DISP1_DAT12__DISP1_DAT12	0x5
> > +			MX51_PAD_DISP1_DAT13__DISP1_DAT13	0x5
> > +			MX51_PAD_DISP1_DAT14__DISP1_DAT14	0x5
> > +			MX51_PAD_DISP1_DAT15__DISP1_DAT15	0x5
> > +			MX51_PAD_DISP1_DAT16__DISP1_DAT16	0x5
> > +			MX51_PAD_DISP1_DAT17__DISP1_DAT17	0x5
> > +			MX51_PAD_DISP1_DAT18__DISP1_DAT18	0x5
> > +			MX51_PAD_DISP1_DAT19__DISP1_DAT19	0x5
> > +			MX51_PAD_DISP1_DAT20__DISP1_DAT20	0x5
> > +			MX51_PAD_DISP1_DAT21__DISP1_DAT21	0x5
> > +			MX51_PAD_DISP1_DAT22__DISP1_DAT22	0x5
> > +			MX51_PAD_DISP1_DAT23__DISP1_DAT23	0x5
> > +			MX51_PAD_DI1_PIN2__DI1_PIN2		0x5
> > +			MX51_PAD_DI1_PIN3__DI1_PIN3		0x5
> > +			MX51_PAD_DI2_DISP_CLK__DI2_DISP_CLK	0x5
> > +			MX51_PAD_DI_GP4__DI2_PIN15		0x5
> > +		>;
> > +	};
> > +
> > +	pinctrl_pwm_backlight: backlightgrp {
> > +		fsl,pins = <
> > +			MX51_PAD_GPIO1_2__PWM1_PWMO		0x80000000
> > +		>;
> > +	};
> > +
> >  	pinctrl_uart1: uart1grp {
> >  		fsl,pins = <
> >  			MX51_PAD_UART1_RXD__UART1_RXD		0x1c5
> > -- 
> > 2.5.0
> > 
> >