[PATCH 2/3] doc: dt-binding: generic onboard USB HUB

[Peter Chen]

On Tue, Dec 15, 2015 at 09:21:09PM +0100, Ulf Hansson wrote:
> On 9 December 2015 at 09:55, Arnd Bergmann <arnd at arndb.de> wrote:
> > On Wednesday 09 December 2015 16:12:24 Peter Chen wrote:
> >> On Tue, Dec 08, 2015 at 09:24:03PM -0600, Rob Herring wrote:
> >> > On Tue, Dec 08, 2015 at 10:58:48AM +0100, Arnd Bergmann wrote:
> >> > > On Tuesday 08 December 2015 10:50:49 Philipp Zabel wrote:
> >> > > > This something we don't have to define ad-hoc. The hub hangs off an USB
> >> > > > controller, right? The "Open Firmware recommended practice: USB"
> >> > > > document already describes how to represent USB devices in a generic
> >> > > > manner:
> >> > > > http://www.firmware.org/1275/bindings/usb/usb-1_0.ps
> >> > > >
> >> > > > Is there a reason not to reuse this?
> >> > > >
> >> > > > The usb hub node would be a child of the usb controller node, and it
> >> > > > could use
> >> > > >         compatible = "usb,class9"; /* bDeviceClass 9 (Hub) */
> >> > >
> >> > > Good point, I had not thought of that when I looked at the patches.
> >> > >
> >> > > Yes, let's do this way. I don't know if we ever implemented the simple
> >> > > patch to associate a USB device with a device_node, but if not, then
> >> > > let's do it now for this driver. A lot of people have asked for it in
> >> > > the past.
> >> >
> >> > Agreed. Also, some hubs have I2C buses as well, but I still think under
> >> > the USB bus is the right place.
> >> >
> >> > However, one complication here is often (probably this case) these
> >> > addtional signals need to be controlled before the device enumerates.
> >> >
> >>
> >> Yes, I did not find a way to let the USB bus code handle it, so I had to
> >> write a platform driver to do it
> >
> > Looping in Ulf, he solved the same problem for SDIO devices recently,
> > and probably remembers the details best.
> >
> 
> Thanks Arnd!
> 
> Yes, that was a kind of a long outstanding issue we have had for SDIO devices.
> 
> Several generic attempts was made to have a framework/library
> available to support so called "power sequences" for exactly the same
> reasons as above.
> Others and myself failed to get those attempts accepted.
> 
> Instead, I invented a mmc subsystem specific DT based solution, the
> "mmc-pwrseq".
> 
> DT documentation:
> Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt
> Documentation/devicetree/bindings/mmc/mmc.txt
> 
> Long story short: The mmc host device may contain a phandle to a
> mmc-pwrseq, which will describe the resources needed to power on/off
> the SDIO card.
> 
> The code is available at:
> drivers/mmc/core/pwrseq*
> 
> We didn't implement this as platform driver, but that was mostly
> because I initially wanted things to be simple. Although, nothing
> prevents us from converting to this as a follow up, which would make
> the solution a bit less "hacky".
> 

Thanks for your information, Ulf.

-- 

Best Regards,
Peter Chen