[PATCH v3 4/4] ARM: dts: <am4372/dra7/omap5>: Use "syscon-phy-power" instead of "ctrl-module"
Kishon Vijay Abraham I
kishon at ti.com
Tue Dec 15 01:39:06 PST 2015
Add "syscon-phy-power" property and remove the deprecated "ctrl-module"
property from SATA and USB PHY node. Also remove the unused control
module dt nodes.
Signed-off-by: Kishon Vijay Abraham I <kishon at ti.com>
---
arch/arm/boot/dts/am4372.dtsi | 16 ++--------------
arch/arm/boot/dts/dra7.dtsi | 34 ++++------------------------------
arch/arm/boot/dts/omap5.dtsi | 26 +++-----------------------
3 files changed, 9 insertions(+), 67 deletions(-)
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index d83ff9c..f42d4a4 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -853,18 +853,6 @@
status = "disabled";
};
- am43xx_control_usb2phy1: control-phy at 44e10620 {
- compatible = "ti,control-phy-usb2-am437";
- reg = <0x44e10620 0x4>;
- reg-names = "power";
- };
-
- am43xx_control_usb2phy2: control-phy at 0x44e10628 {
- compatible = "ti,control-phy-usb2-am437";
- reg = <0x44e10628 0x4>;
- reg-names = "power";
- };
-
ocp2scp0: ocp2scp at 483a8000 {
compatible = "ti,am437x-ocp2scp", "ti,omap-ocp2scp";
#address-cells = <1>;
@@ -875,7 +863,7 @@
usb2_phy1: phy at 483a8000 {
compatible = "ti,am437x-usb2";
reg = <0x483a8000 0x8000>;
- ctrl-module = <&am43xx_control_usb2phy1>;
+ syscon-phy-power = <&scm_conf 0x620>;
clocks = <&usb_phy0_always_on_clk32k>,
<&usb_otg_ss0_refclk960m>;
clock-names = "wkupclk", "refclk";
@@ -894,7 +882,7 @@
usb2_phy2: phy at 483e8000 {
compatible = "ti,am437x-usb2";
reg = <0x483e8000 0x8000>;
- ctrl-module = <&am43xx_control_usb2phy2>;
+ syscon-phy-power = <&scm_conf 0x628>;
clocks = <&usb_phy1_always_on_clk32k>,
<&usb_otg_ss1_refclk960m>;
clock-names = "wkupclk", "refclk";
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 41545f9..8ce37e4 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -1170,14 +1170,6 @@
status = "disabled";
};
- omap_control_sata: control-phy at 4a002374 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002374 0x4>;
- reg-names = "power";
- clocks = <&sys_clkin1>;
- clock-names = "sysclk";
- };
-
/* OCP2SCP3 */
ocp2scp at 4a090000 {
compatible = "ti,omap-ocp2scp";
@@ -1192,7 +1184,7 @@
<0x4A096400 0x64>, /* phy_tx */
<0x4A096800 0x40>; /* pll_ctrl */
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_sata>;
+ syscon-phy-power = <&scm_conf 0x374>;
clocks = <&sys_clkin1>, <&sata_ref_clk>;
clock-names = "sysclk", "refclk";
syscon-pllreset = <&scm_conf 0x3fc>;
@@ -1260,24 +1252,6 @@
clocks = <&sys_32k_ck>;
};
- omap_control_usb2phy1: control-phy at 4a002300 {
- compatible = "ti,control-phy-usb2";
- reg = <0x4a002300 0x4>;
- reg-names = "power";
- };
-
- omap_control_usb3phy1: control-phy at 4a002370 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002370 0x4>;
- reg-names = "power";
- };
-
- omap_control_usb2phy2: control-phy at 0x4a002e74 {
- compatible = "ti,control-phy-usb2-dra7";
- reg = <0x4a002e74 0x4>;
- reg-names = "power";
- };
-
/* OCP2SCP1 */
ocp2scp at 4a080000 {
compatible = "ti,omap-ocp2scp";
@@ -1290,7 +1264,7 @@
usb2_phy1: phy at 4a084000 {
compatible = "ti,omap-usb2";
reg = <0x4a084000 0x400>;
- ctrl-module = <&omap_control_usb2phy1>;
+ syscon-phy-power = <&scm_conf 0x300>;
clocks = <&usb_phy1_always_on_clk32k>,
<&usb_otg_ss1_refclk960m>;
clock-names = "wkupclk",
@@ -1302,7 +1276,7 @@
compatible = "ti,dra7x-usb2-phy2",
"ti,omap-usb2";
reg = <0x4a085000 0x400>;
- ctrl-module = <&omap_control_usb2phy2>;
+ syscon-phy-power = <&scm_conf 0xe74>;
clocks = <&usb_phy2_always_on_clk32k>,
<&usb_otg_ss2_refclk960m>;
clock-names = "wkupclk",
@@ -1316,7 +1290,7 @@
<0x4a084800 0x64>,
<0x4a084c00 0x40>;
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_usb3phy1>;
+ syscon-phy-power = <&scm_conf 0x370>;
clocks = <&usb_phy3_always_on_clk32k>,
<&sys_clkin1>,
<&usb_otg_ss1_refclk960m>;
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index 4c04389..f6d6d91 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -850,18 +850,6 @@
hw-caps-temp-alert;
};
- omap_control_usb2phy: control-phy at 4a002300 {
- compatible = "ti,control-phy-usb2";
- reg = <0x4a002300 0x4>;
- reg-names = "power";
- };
-
- omap_control_usb3phy: control-phy at 4a002370 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002370 0x4>;
- reg-names = "power";
- };
-
usb3: omap_dwc3 at 4a020000 {
compatible = "ti,dwc3";
ti,hwmods = "usb_otg_ss";
@@ -897,7 +885,7 @@
usb2_phy: usb2phy at 4a084000 {
compatible = "ti,omap-usb2";
reg = <0x4a084000 0x7c>;
- ctrl-module = <&omap_control_usb2phy>;
+ syscon-phy-power = <&scm_conf 0x300>;
clocks = <&usb_phy_cm_clk32k>, <&usb_otg_ss_refclk960m>;
clock-names = "wkupclk", "refclk";
#phy-cells = <0>;
@@ -909,7 +897,7 @@
<0x4a084800 0x64>,
<0x4a084c00 0x40>;
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_usb3phy>;
+ syscon-phy-power = <&scm_conf 0x370>;
clocks = <&usb_phy_cm_clk32k>,
<&sys_clkin>,
<&usb_otg_ss_refclk960m>;
@@ -965,14 +953,6 @@
#thermal-sensor-cells = <1>;
};
- omap_control_sata: control-phy at 4a002374 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002374 0x4>;
- reg-names = "power";
- clocks = <&sys_clkin>;
- clock-names = "sysclk";
- };
-
/* OCP2SCP3 */
ocp2scp at 4a090000 {
compatible = "ti,omap-ocp2scp";
@@ -987,7 +967,7 @@
<0x4A096400 0x64>, /* phy_tx */
<0x4A096800 0x40>; /* pll_ctrl */
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_sata>;
+ syscon-phy-power = <&scm_conf 0x374>;
clocks = <&sys_clkin>, <&sata_ref_clk>;
clock-names = "sysclk", "refclk";
#phy-cells = <0>;
--
1.7.9.5
More information about the linux-arm-kernel
mailing list