[PATCHv2] ARM: dts: kirkwood: Add DTS for Zyxel NSA325
Hans Ulli Kroll
ulli.kroll at googlemail.com
Wed Dec 9 21:33:08 PST 2015
Add a new DTS file to support the Zyxel NSA325(v2) dual bay
NAS device, based on the NSA320 DTS files.
The only difference to the NSA320 device is GPIO47.
This en/disables the power for the hdd in slot2, currently
fixed to on.
Signed-off-by: Hans Ulli Kroll <ulli.kroll at googlemail.com>
---
v2
- using kirkwood-nsa325.dts as template, this removes the odd
indentation and unneeded partitions nodes.
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/kirkwood-nsa325.dts | 236 ++++++++++++++++++++++++++++++++++
2 files changed, 237 insertions(+)
create mode 100644 arch/arm/boot/dts/kirkwood-nsa325.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index bb8fa02..0fcae90 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -193,6 +193,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
kirkwood-ns2mini.dtb \
kirkwood-nsa310.dtb \
kirkwood-nsa310a.dtb \
+ kirkwood-nsa325.dtb \
kirkwood-openblocks_a6.dtb \
kirkwood-openblocks_a7.dtb \
kirkwood-openrd-base.dtb \
diff --git a/arch/arm/boot/dts/kirkwood-nsa325.dts b/arch/arm/boot/dts/kirkwood-nsa325.dts
new file mode 100644
index 0000000..6e9ffb5
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-nsa325.dts
@@ -0,0 +1,236 @@
+/* Device tree file for the Zyxel NSA 325 NAS box.
+ *
+ * Copyright (c) 2015, Hans Ulli Kroll <ulli.kroll at googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ *
+ * Based upon the board setup file created by Peter Schildmann */
+
+/dts-v1/;
+
+#include "kirkwood-nsa3x0-common.dtsi"
+
+/ {
+ model = "ZyXEL NSA325";
+ compatible = "zyxel,nsa325", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ stdout-path = &uart0;
+ };
+
+ mbus {
+ pcie-controller {
+ status = "okay";
+
+ pcie at 1,0 {
+ status = "okay";
+ };
+ };
+ };
+
+ ocp at f1000000 {
+ pinctrl: pin-controller at 10000 {
+ pinctrl-names = "default";
+
+ pmx_led_hdd2_green: pmx-led-hdd2-green {
+ marvell,pins = "mpp12";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_hdd2_red: pmx-led-hdd2-red {
+ marvell,pins = "mpp13";
+ marvell,function = "gpio";
+ };
+
+ pmx_mcu_data: pmx-mcu-data {
+ marvell,pins = "mpp14";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_usb_green: pmx-led-usb-green {
+ marvell,pins = "mpp15";
+ marvell,function = "gpio";
+ };
+
+ pmx_mcu_clk: pmx-mcu-clk {
+ marvell,pins = "mpp16";
+ marvell,function = "gpio";
+ };
+
+ pmx_mcu_act: pmx-mcu-act {
+ marvell,pins = "mpp17";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_sys_green: pmx-led-sys-green {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_sys_orange: pmx-led-sys-orange {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_hdd1_green: pmx-led-hdd1-green {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_hdd1_red: pmx-led-hdd1-red {
+ marvell,pins = "mpp42";
+ marvell,function = "gpio";
+ };
+
+ pmx_htp: pmx-htp {
+ marvell,pins = "mpp43";
+ marvell,function = "gpio";
+ };
+
+ /* Buzzer needs to be switched at around 1kHz so is
+ not compatible with the gpio-beeper driver. */
+ pmx_buzzer: pmx-buzzer {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+
+ pmx_vid_b1: pmx-vid-b1 {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+
+ pmx_power_resume_data: pmx-power-resume-data {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+
+ pmx_power_resume_clk: pmx-power-resume-clk {
+ marvell,pins = "mpp49";
+ marvell,function = "gpio";
+ };
+
+ pmx_pwr_sata1: pmx-pwr-sata1 {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ };
+
+ /* This board uses the pcf8563 RTC instead of the SoC RTC */
+ rtc at 10300 {
+ status = "disabled";
+ };
+
+ i2c at 11000 {
+ status = "okay";
+
+ pcf8563: pcf8563 at 51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_pwr_sata1>;
+ pinctrl-names = "default";
+
+ usb0_power: regulator at 1 {
+ enable-active-high;
+ };
+
+ sata1_power: regulator at 2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "SATA1 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_led_hdd2_green &pmx_led_hdd2_red
+ &pmx_led_usb_green
+ &pmx_led_sys_green &pmx_led_sys_orange
+ &pmx_led_copy_green &pmx_led_copy_red
+ &pmx_led_hdd1_green &pmx_led_hdd1_red>;
+ pinctrl-names = "default";
+
+ green-sys {
+ label = "nsa325:green:sys";
+ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+ };
+ orange-sys {
+ label = "nsa325:orange:sys";
+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ };
+ green-hdd1 {
+ label = "nsa325:green:hdd1";
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ };
+ red-hdd1 {
+ label = "nsa325:red:hdd1";
+ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+ };
+ green-hdd2 {
+ label = "nsa325:green:hdd2";
+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ };
+ red-hdd2 {
+ label = "nsa325:red:hdd2";
+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+ };
+ green-usb {
+ label = "nsa325:green:usb";
+ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+ };
+ green-copy {
+ label = "nsa325:green:copy";
+ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ };
+ red-copy {
+ label = "nsa325:red:copy";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* The following pins are currently not assigned to a driver,
+ some of them should be configured as inputs.
+ pinctrl-0 = <&pmx_mcu_data &pmx_mcu_clk &pmx_mcu_act
+ &pmx_htp &pmx_vid_b1
+ &pmx_power_resume_data &pmx_power_resume_clk>; */
+
+ };
+
+
+};
+
+&mdio {
+ status = "okay";
+ ethphy0: ethernet-phy at 1 {
+ reg = <1>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port at 0 {
+ phy-handle = <ðphy0>;
+ };
+};
+
--
2.6.0
More information about the linux-arm-kernel
mailing list