[PATCH v7 3/6] watchdog: ts4800: add driver for TS-4800 watchdog
Damien Riegel
damien.riegel at savoirfairelinux.com
Fri Dec 4 10:49:33 PST 2015
Hi Wim,
This patch is part of a serie and Lee Jones was willing to handle the
serie (at least the first three patches) but he needs your Ack on the
watchdog as you are the maintainer of this subsystem. This patch has
already been reviewed by Guenter. Could you please review this patch ?
Thanks,
Damien
On Mon, Nov 30, 2015 at 08:14:48AM -0800, Guenter Roeck wrote:
> On 11/30/2015 07:59 AM, Damien Riegel wrote:
> >This watchdog is instantiated in a FPGA that is memory mapped. It is
> >made of only one register, called the feed register. Writing to this
> >register will re-arm the watchdog for a given time (and enable it if it
> >was disable). It can be disabled by writing a special value into it.
> >
> >It is part of a syscon block, and the watchdog register offset in this
> >block varies from board to board. This offset is passed in the syscon
> >property after the phandle to the syscon node.
> >
> >Signed-off-by: Damien Riegel <damien.riegel at savoirfairelinux.com>
>
> Reviewed-by: Guenter Roeck <linux at roeck-us.net>
>
> >---
> > .../devicetree/bindings/watchdog/ts4800-wdt.txt | 25 +++
> > drivers/watchdog/Kconfig | 10 +
> > drivers/watchdog/Makefile | 1 +
> > drivers/watchdog/ts4800_wdt.c | 215 +++++++++++++++++++++
> > 4 files changed, 251 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/watchdog/ts4800-wdt.txt
> > create mode 100644 drivers/watchdog/ts4800_wdt.c
> >
> >diff --git a/Documentation/devicetree/bindings/watchdog/ts4800-wdt.txt b/Documentation/devicetree/bindings/watchdog/ts4800-wdt.txt
> >new file mode 100644
> >index 0000000..8f6caad
> >--- /dev/null
> >+++ b/Documentation/devicetree/bindings/watchdog/ts4800-wdt.txt
> >@@ -0,0 +1,25 @@
> >+Technologic Systems Watchdog
> >+
> >+Required properties:
> >+- compatible: must be "technologic,ts4800-wdt"
> >+- syscon: phandle / integer array that points to the syscon node which
> >+ describes the FPGA's syscon registers.
> >+ - phandle to FPGA's syscon
> >+ - offset to the watchdog register
> >+
> >+Optional property:
> >+- timeout-sec: contains the watchdog timeout in seconds.
> >+
> >+Example:
> >+
> >+syscon: syscon at b0010000 {
> >+ compatible = "syscon", "simple-mfd";
> >+ reg = <0xb0010000 0x3d>;
> >+ reg-io-width = <2>;
> >+
> >+ wdt at e {
> >+ compatible = "technologic,ts4800-wdt";
> >+ syscon = <&syscon 0xe>;
> >+ timeout-sec = <10>;
> >+ };
> >+}
> >diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
> >index 79e1aa1..bb624d2 100644
> >--- a/drivers/watchdog/Kconfig
> >+++ b/drivers/watchdog/Kconfig
> >@@ -426,6 +426,16 @@ config NUC900_WATCHDOG
> > To compile this driver as a module, choose M here: the
> > module will be called nuc900_wdt.
> >
> >+config TS4800_WATCHDOG
> >+ tristate "TS-4800 Watchdog"
> >+ depends on HAS_IOMEM && OF
> >+ select WATCHDOG_CORE
> >+ select MFD_SYSCON
> >+ help
> >+ Technologic Systems TS-4800 has watchdog timer implemented in
> >+ an external FPGA. Say Y here if you want to support for the
> >+ watchdog timer on TS-4800 board.
> >+
> > config TS72XX_WATCHDOG
> > tristate "TS-72XX SBC Watchdog"
> > depends on MACH_TS72XX
> >diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
> >index 0c616e3..3863ce0 100644
> >--- a/drivers/watchdog/Makefile
> >+++ b/drivers/watchdog/Makefile
> >@@ -53,6 +53,7 @@ obj-$(CONFIG_RN5T618_WATCHDOG) += rn5t618_wdt.o
> > obj-$(CONFIG_COH901327_WATCHDOG) += coh901327_wdt.o
> > obj-$(CONFIG_STMP3XXX_RTC_WATCHDOG) += stmp3xxx_rtc_wdt.o
> > obj-$(CONFIG_NUC900_WATCHDOG) += nuc900_wdt.o
> >+obj-$(CONFIG_TS4800_WATCHDOG) += ts4800_wdt.o
> > obj-$(CONFIG_TS72XX_WATCHDOG) += ts72xx_wdt.o
> > obj-$(CONFIG_IMX2_WDT) += imx2_wdt.o
> > obj-$(CONFIG_UX500_WATCHDOG) += ux500_wdt.o
> >diff --git a/drivers/watchdog/ts4800_wdt.c b/drivers/watchdog/ts4800_wdt.c
> >new file mode 100644
> >index 0000000..2b8de86
> >--- /dev/null
> >+++ b/drivers/watchdog/ts4800_wdt.c
> >@@ -0,0 +1,215 @@
> >+/*
> >+ * Watchdog driver for TS-4800 based boards
> >+ *
> >+ * Copyright (c) 2015 - Savoir-faire Linux
> >+ *
> >+ * This file is licensed under the terms of the GNU General Public
> >+ * License version 2. This program is licensed "as is" without any
> >+ * warranty of any kind, whether express or implied.
> >+ */
> >+
> >+#include <linux/kernel.h>
> >+#include <linux/mfd/syscon.h>
> >+#include <linux/module.h>
> >+#include <linux/of.h>
> >+#include <linux/platform_device.h>
> >+#include <linux/regmap.h>
> >+#include <linux/watchdog.h>
> >+
> >+static bool nowayout = WATCHDOG_NOWAYOUT;
> >+module_param(nowayout, bool, 0);
> >+MODULE_PARM_DESC(nowayout,
> >+ "Watchdog cannot be stopped once started (default="
> >+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
> >+
> >+/* possible feed values */
> >+#define TS4800_WDT_FEED_2S 0x1
> >+#define TS4800_WDT_FEED_10S 0x2
> >+#define TS4800_WDT_DISABLE 0x3
> >+
> >+struct ts4800_wdt {
> >+ struct watchdog_device wdd;
> >+ struct regmap *regmap;
> >+ u32 feed_offset;
> >+ u32 feed_val;
> >+};
> >+
> >+/*
> >+ * TS-4800 supports the following timeout values:
> >+ *
> >+ * value desc
> >+ * ---------------------
> >+ * 0 feed for 338ms
> >+ * 1 feed for 2.706s
> >+ * 2 feed for 10.824s
> >+ * 3 disable watchdog
> >+ *
> >+ * Keep the regmap/timeout map ordered by timeout
> >+ */
> >+static const struct {
> >+ const int timeout;
> >+ const int regval;
> >+} ts4800_wdt_map[] = {
> >+ { 2, TS4800_WDT_FEED_2S },
> >+ { 10, TS4800_WDT_FEED_10S },
> >+};
> >+
> >+#define MAX_TIMEOUT_INDEX (ARRAY_SIZE(ts4800_wdt_map) - 1)
> >+
> >+static void ts4800_write_feed(struct ts4800_wdt *wdt, u32 val)
> >+{
> >+ regmap_write(wdt->regmap, wdt->feed_offset, val);
> >+}
> >+
> >+static int ts4800_wdt_start(struct watchdog_device *wdd)
> >+{
> >+ struct ts4800_wdt *wdt = watchdog_get_drvdata(wdd);
> >+
> >+ ts4800_write_feed(wdt, wdt->feed_val);
> >+ return 0;
> >+}
> >+
> >+static int ts4800_wdt_stop(struct watchdog_device *wdd)
> >+{
> >+ struct ts4800_wdt *wdt = watchdog_get_drvdata(wdd);
> >+
> >+ ts4800_write_feed(wdt, TS4800_WDT_DISABLE);
> >+ return 0;
> >+}
> >+
> >+static int ts4800_wdt_set_timeout(struct watchdog_device *wdd,
> >+ unsigned int timeout)
> >+{
> >+ struct ts4800_wdt *wdt = watchdog_get_drvdata(wdd);
> >+ int i;
> >+
> >+ for (i = 0; i < MAX_TIMEOUT_INDEX; i++) {
> >+ if (ts4800_wdt_map[i].timeout >= timeout)
> >+ break;
> >+ }
> >+
> >+ wdd->timeout = ts4800_wdt_map[i].timeout;
> >+ wdt->feed_val = ts4800_wdt_map[i].regval;
> >+
> >+ return 0;
> >+}
> >+
> >+static const struct watchdog_ops ts4800_wdt_ops = {
> >+ .owner = THIS_MODULE,
> >+ .start = ts4800_wdt_start,
> >+ .stop = ts4800_wdt_stop,
> >+ .set_timeout = ts4800_wdt_set_timeout,
> >+};
> >+
> >+static const struct watchdog_info ts4800_wdt_info = {
> >+ .options = WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE | WDIOF_KEEPALIVEPING,
> >+ .identity = "TS-4800 Watchdog",
> >+};
> >+
> >+static int ts4800_wdt_probe(struct platform_device *pdev)
> >+{
> >+ struct device_node *np = pdev->dev.of_node;
> >+ struct device_node *syscon_np;
> >+ struct watchdog_device *wdd;
> >+ struct ts4800_wdt *wdt;
> >+ u32 reg;
> >+ int ret;
> >+
> >+ syscon_np = of_parse_phandle(np, "syscon", 0);
> >+ if (!syscon_np) {
> >+ dev_err(&pdev->dev, "no syscon property\n");
> >+ return -ENODEV;
> >+ }
> >+
> >+ ret = of_property_read_u32_index(np, "syscon", 1, ®);
> >+ if (ret < 0) {
> >+ dev_err(&pdev->dev, "no offset in syscon\n");
> >+ return ret;
> >+ }
> >+
> >+ /* allocate memory for watchdog struct */
> >+ wdt = devm_kzalloc(&pdev->dev, sizeof(*wdt), GFP_KERNEL);
> >+ if (!wdt)
> >+ return -ENOMEM;
> >+
> >+ /* set regmap and offset to know where to write */
> >+ wdt->feed_offset = reg;
> >+ wdt->regmap = syscon_node_to_regmap(syscon_np);
> >+ if (IS_ERR(wdt->regmap)) {
> >+ dev_err(&pdev->dev, "cannot get parent's regmap\n");
> >+ return PTR_ERR(wdt->regmap);
> >+ }
> >+
> >+ /* Initialize struct watchdog_device */
> >+ wdd = &wdt->wdd;
> >+ wdd->parent = &pdev->dev;
> >+ wdd->info = &ts4800_wdt_info;
> >+ wdd->ops = &ts4800_wdt_ops;
> >+ wdd->min_timeout = ts4800_wdt_map[0].timeout;
> >+ wdd->max_timeout = ts4800_wdt_map[MAX_TIMEOUT_INDEX].timeout;
> >+
> >+ watchdog_set_drvdata(wdd, wdt);
> >+ watchdog_set_nowayout(wdd, nowayout);
> >+ watchdog_init_timeout(wdd, 0, &pdev->dev);
> >+
> >+ /*
> >+ * As this watchdog supports only a few values, ts4800_wdt_set_timeout
> >+ * must be called to initialize timeout and feed_val with valid values.
> >+ * Default to maximum timeout if none, or an invalid one, is provided in
> >+ * device tree.
> >+ */
> >+ if (!wdd->timeout)
> >+ wdd->timeout = wdd->max_timeout;
> >+ ts4800_wdt_set_timeout(wdd, wdd->timeout);
> >+
> >+ /*
> >+ * The feed register is write-only, so it is not possible to determine
> >+ * watchdog's state. Disable it to be in a known state.
> >+ */
> >+ ts4800_wdt_stop(wdd);
> >+
> >+ ret = watchdog_register_device(wdd);
> >+ if (ret) {
> >+ dev_err(&pdev->dev,
> >+ "failed to register watchdog device\n");
> >+ return ret;
> >+ }
> >+
> >+ platform_set_drvdata(pdev, wdt);
> >+
> >+ dev_info(&pdev->dev,
> >+ "initialized (timeout = %d sec, nowayout = %d)\n",
> >+ wdd->timeout, nowayout);
> >+
> >+ return 0;
> >+}
> >+
> >+static int ts4800_wdt_remove(struct platform_device *pdev)
> >+{
> >+ struct ts4800_wdt *wdt = platform_get_drvdata(pdev);
> >+
> >+ watchdog_unregister_device(&wdt->wdd);
> >+
> >+ return 0;
> >+}
> >+
> >+static const struct of_device_id ts4800_wdt_of_match[] = {
> >+ { .compatible = "technologic,ts4800-wdt", },
> >+ { },
> >+};
> >+MODULE_DEVICE_TABLE(of, ts4800_wdt_of_match);
> >+
> >+static struct platform_driver ts4800_wdt_driver = {
> >+ .probe = ts4800_wdt_probe,
> >+ .remove = ts4800_wdt_remove,
> >+ .driver = {
> >+ .name = "ts4800_wdt",
> >+ .of_match_table = ts4800_wdt_of_match,
> >+ },
> >+};
> >+
> >+module_platform_driver(ts4800_wdt_driver);
> >+
> >+MODULE_AUTHOR("Damien Riegel <damien.riegel at savoirfairelinux.com>");
> >+MODULE_LICENSE("GPL v2");
> >+MODULE_ALIAS("platform:ts4800_wdt");
> >
>
More information about the linux-arm-kernel
mailing list