[PATCH 7/7] ARM: dts: Enable emmc on hp t410

[Peter Ujfalusi]

On 12/04/2015 03:25 AM, Tony Lindgren wrote:
> There's a 2GB emmc on hp t410 that's wired to the sd_2 interface.
> Note that we also need to configure the evtmux using edma_xbar for
> edma channels.
> 
> Signed-off-by: Tony Lindgren <tony at atomide.com>

One question inlined for the mmc3, other than that:
Reviewed-by: Peter Ujfalusi <peter.ujfalusi at ti.com>

> ---
>  arch/arm/boot/dts/dm8148-t410.dts | 35 +++++++++++++++++++++++++++++++++++
>  1 file changed, 35 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/dm8148-t410.dts b/arch/arm/boot/dts/dm8148-t410.dts
> index 79838dd..d1927a7 100644
> --- a/arch/arm/boot/dts/dm8148-t410.dts
> +++ b/arch/arm/boot/dts/dm8148-t410.dts
> @@ -15,6 +15,13 @@
>  		device_type = "memory";
>  		reg = <0x80000000 0x40000000>;	/* 1 GB */
>  	};
> +
> +	vmmcsd_fixed: fixedregulator at 0 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vmmcsd_fixed";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
>  };
>  
>  &cpsw_emac0 {
> @@ -26,3 +33,31 @@
>  	phy_id = <&davinci_mdio>, <1>;
>  	phy-mode = "rgmii";
>  };
> +
> +&mmc3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sd2_pins>;
> +	vmmc-supply = <&vmmcsd_fixed>;
> +	bus-width = <8>;
> +	dmas = <&edma_xbar 8 0 1	/* use SDTXEVT1 instead of MCASP0TX */
> +		&edma_xbar 9 0 2>;	/* use SDRXEVT1 instead of MCASP0RX */
> +	dma-names = "tx", "rx";

Do you happened to know how the audio is connected on the board?
The DM814x-EVM seams to be using McASP2 with aic3106 so it is possible that HP
copied the design from there...

> +};
> +
> +&pincntl {
> +	sd2_pins: pinmux_sd2_pins {
> +		pinctrl-single,pins = <
> +			DM814X_IOPAD(0x09c0, PIN_INPUT_PULLUP | 0x1)	/* SD2_DAT[7] */
> +			DM814X_IOPAD(0x09c4, PIN_INPUT_PULLUP | 0x1)	/* SD2_DAT[6] */
> +			DM814X_IOPAD(0x09c8, PIN_INPUT_PULLUP | 0x1)	/* SD2_DAT[5] */
> +			DM814X_IOPAD(0x09cc, PIN_INPUT_PULLUP | 0x1)	/* SD2_DAT[4] */
> +			DM814X_IOPAD(0x09d0, PIN_INPUT_PULLUP | 0x1)	/* SD2_DAT[3] */
> +			DM814X_IOPAD(0x09d4, PIN_INPUT_PULLUP | 0x1)	/* SD2_DAT[2] */
> +			DM814X_IOPAD(0x09d8, PIN_INPUT_PULLUP | 0x1)	/* SD2_DAT[1] */
> +			DM814X_IOPAD(0x09dc, PIN_INPUT_PULLUP | 0x1)	/* SD2_DAT[0] */
> +			DM814X_IOPAD(0x09e0, PIN_INPUT | 0x1)		/* SD2_CLK */
> +			DM814X_IOPAD(0x09f4, PIN_INPUT_PULLUP | 0x2)	/* SD2_CMD */
> +			DM814X_IOPAD(0x0920, PIN_INPUT | 40)	/* SD2_SDCD */
> +			>;
> +	};
> +};
> 


-- 
Péter