[PATCH v3] ARM: mvebu: Disable CPU Idle on Armada 38x

[Gregory CLEMENT]

Hi Russell King,
 
 On sam., oct. 03 2015, Russell King - ARM Linux <linux at arm.linux.org.uk> wrote:

> On Tue, Mar 31, 2015 at 06:46:18PM +0200, Gregory CLEMENT wrote:
>> On Armada 38x SoCs, under heavy I/O load, the system hangs when CPU
>> Idle is enabled. Waiting for a solution to this issue, this patch
>> disables the CPU Idle support for this SoC.
>> 
>> As CPU Hot plug support also uses some of the CPU Idle functions it is
>> also affected by the same issue. This patch disables it also for the
>> Armada 38x SoCs.
>> 
>> Signed-off-by: Gregory CLEMENT <gregory.clement at free-electrons.com>
>> Tested-by: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
>> Cc: <stable at vger.kernel.org> # v3.17 +
>> ---
>> Hi,
>> 
>> In this version I removed the unneeded initialization of the ret
>> variable, I also fixed the warning message, and finally I added the
>> Tested-by from Thomas.
>
> In order not to lose the results of my testing on Armada 388, and to
> trigger a discussion, I'll reply to this mail.
>
> With the Armada 388 board I have, running mainline 4.3-rc3, I see the
> following board current and power consumption:
>
> CPU idle state					Current	Power
> Patch unreverted				0.33A	3.9W
> Patch reverted					0.42A	5W
> Patch reverted, state 1 disabled on one CPU	0.37A	4.4W
> Patch reverted, state 1 disabled on both CPUs	0.33A	3.9W
> Patch reverted, state 1 disabled on both CPUs,	0.37A	4.4W
> CPU 1 hot-unplugged
> Marvell Vendor-based kernel with CPU idle off	0.37A	4.4W
> (I don't have a vendor kernel with CPU idle enabled)
>
> This is with a mainline 4.3-rc3 kernel with my own patch set on top,
> which includes things like EEE support giving a 360mW saving compared
> to kernels without.
>
> The result is a 30% _increase_ in power consumption when CPU idle is
> enabled.  For reference, when placing both CPUs into a loop via
> while :; do :; done in bash, the consumption goes up to 0.5A / 6W.
>
> Thomas suggested to increase the CPU idle thresholds in a similar manner
> to that done for Armada XP in ce6031c89a35 ("cpuidle: mvebu: Update
> cpuidle thresholds for Armada XP SOCs"), so I made the following change:
>
> @@ -92,9 +92,9 @@ static struct cpuidle_driver armada38x_idle_driver = {
> -               .exit_latency           = 10,
> +               .exit_latency           = 100,
> -               .target_residency       = 100,
> +               .target_residency       = 1000,
>
> This had no effect on the power usage.
>
> This brings up the obvious question, is there a bug somewhere, resulting
> in suspending the CPU not resulting in power savings?
>
> I don't think so.  I've fixed the failure path in the mvebu CPU idle code
> as per the RFC I sent out earlier this morning, which means if we fail to
> suspend the CPU, time will not be accounted to CPU idle state 1 - this
> means we can be sure that the statistics for state 1 won't be incorrectly
> incremented.  The CPU idle statistics indicate that we are hitting the
> lower power state 1, and spending some time there for each call:
>
> /sys/devices/system/cpu/cpu0/cpuidle/state0/time:24726278
> /sys/devices/system/cpu/cpu0/cpuidle/state0/usage:29991
> /sys/devices/system/cpu/cpu0/cpuidle/state1/time:290135931
> /sys/devices/system/cpu/cpu0/cpuidle/state1/usage:74951
> /sys/devices/system/cpu/cpu1/cpuidle/state0/time:41096682
> /sys/devices/system/cpu/cpu1/cpuidle/state0/usage:141538
> /sys/devices/system/cpu/cpu1/cpuidle/state1/time:270641329
> /sys/devices/system/cpu/cpu1/cpuidle/state1/usage:47845
>
> So we're probably _not_ looping trying to enter state 1 and immediately
> coming back out.  In other words, we are suspending the CPU, and the CPU
> is staying suspended for a period of time.
>
> I think we have to conclude that we are successfully suspending the CPU,
> and that it is resuming through armada_38x_cpu_resume() and cpu_resume()
> as we expect, and the result if placing the CPU into suspend actually
> results in higher power consumption than placing the CPU into WFI
> mode.

I finally managed to measure the power consumption on my Armada 388 GP
board and I confirm what you saw. With CPU idle disable in pmsu.c it
consumes 0.43A at 12V and when it is enable it consumes 0.53A at 12V so around
30% more.

If I disable the state1 on a CPU it goes down 0.49 at 12, and if I disable
the state1 opn both CPU, then it comes back to 0.43A at 12V.

>
> It could be that some register isn't set correctly to allow the CPU
> power domain to be properly shut down.  It could also be that the SoC
> doesn't implement the isolation barrier between the CPU and surrounding
> circuitry, resulting in higher leakage when the CPU is placed into
> suspend mode.  (The SCU power register is always present, but the
> implementation of the isolation barriers to allow individual CPUs to be
> independently powered down are optional.)  Either way, without
> documentation, there's no way to know.

Now that I can reproduce it, I will investigate to find what we do
wrong.

Thanks,

Gregory

-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com