[PATCH v4 5/5] ARM: BCM: Add SMP support for Broadcom 4708

[Hauke Mehrtens]

On 12/01/2015 05:24 PM, Kapil Hali wrote:
> From: Jon Mason <jonmason at broadcom.com>
> 
> Add SMP support for Broadcom's 4708 SoCs.
> 
> Signed-off-by: Jon Mason <jonmason at broadcom.com>
> Acked-by: Hauke Mehrtens <hauke at hauke-m.de>
> Tested-by: Hauke Mehrtens <hauke at hauke-m.de>
> Signed-off-by: Kapil Hali <kapilh at broadcom.com>
> ---
>  arch/arm/boot/dts/bcm4708.dtsi | 2 ++
>  arch/arm/mach-bcm/Kconfig      | 1 +
>  arch/arm/mach-bcm/Makefile     | 3 +++
>  3 files changed, 6 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/bcm4708.dtsi b/arch/arm/boot/dts/bcm4708.dtsi
> index 31141e8..eed4dd1 100644
> --- a/arch/arm/boot/dts/bcm4708.dtsi
> +++ b/arch/arm/boot/dts/bcm4708.dtsi
> @@ -15,6 +15,7 @@
>  	cpus {
>  		#address-cells = <1>;
>  		#size-cells = <0>;
> +		enable-method = "brcm,bcm-nsp-smp";
>  
>  		cpu at 0 {
>  			device_type = "cpu";
> @@ -27,6 +28,7 @@
>  			device_type = "cpu";
>  			compatible = "arm,cortex-a9";
>  			next-level-cache = <&L2>;
> +			secondary-boot-reg = <0xffff0400>;
>  			reg = <0x1>;
>  		};
>  	};
> diff --git a/arch/arm/mach-bcm/Kconfig b/arch/arm/mach-bcm/Kconfig
> index 83765a0..e85246f 100644
> --- a/arch/arm/mach-bcm/Kconfig
> +++ b/arch/arm/mach-bcm/Kconfig
> @@ -54,6 +54,7 @@ config ARCH_BCM_NSP
>  config ARCH_BCM_5301X
>  	bool "Broadcom BCM470X / BCM5301X ARM SoC" if ARCH_MULTI_V7
>  	select ARCH_BCM_IPROC
> +	select HAVE_SMP
>  	help
>  	  Support for Broadcom BCM470X and BCM5301X SoCs with ARM CPU cores.
>  

When applying this patch please make sure it is correctly applied this
patch causes some problems here:

http://www.spinics.net/lists/arm-kernel/msg462137.html

> diff --git a/arch/arm/mach-bcm/Makefile b/arch/arm/mach-bcm/Makefile
> index 5193a25..7d66515 100644
> --- a/arch/arm/mach-bcm/Makefile
> +++ b/arch/arm/mach-bcm/Makefile
> @@ -43,6 +43,9 @@ obj-$(CONFIG_ARCH_BCM2835)	+= board_bcm2835.o
>  
>  # BCM5301X
>  obj-$(CONFIG_ARCH_BCM_5301X)	+= bcm_5301x.o
> +ifeq ($(CONFIG_ARCH_BCM_5301X),y)
> +obj-$(CONFIG_SMP)		+= platsmp.o
> +endif
>  
>  # BCM63XXx
>  ifeq ($(CONFIG_ARCH_BCM_63XX),y)
> 

I am getting this on a Northstar 1 / BCM4708:

[ 0.137634] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.143643] Setting up static identity map for 0x82a0 - 0x82d4
[ 0.189772] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.189861] Brought up 2 CPUs
[ 0.198845] SMP: Total of 2 processors activated (3188.32 BogoMIPS).
[ 0.205446] CPU: WARNING: CPU(s) started in wrong/inconsistent modes
(primary CPU mode 0x13)
[ 0.214167] CPU: This may indicate a broken bootloader or firmware.

I assume that this is correct and the bootloader is just broken, it uses
this bootloader: "CFE for Foxconn Router version: v1.0.14", I haven't
noticed any problems, so it is ok for me.

Hauke