[PATCH v3 4/6] pinctrl: meson: Enable GPIO IRQs

[Carlo Caione]

On Tue, Dec 1, 2015 at 8:16 PM, Marc Zyngier <marc.zyngier at arm.com> wrote:
> On 01/12/15 16:24, Carlo Caione wrote:
>> From: Carlo Caione <carlo at endlessm.com>

>> +static int meson_irq_domain_alloc(struct irq_domain *domain, unsigned int irq,
>> +                               unsigned int nr_irqs, void *arg)
>> +{
>> +     struct meson_pinctrl *pc = domain->host_data;
>> +     struct irq_fwspec *irq_data = arg;
>> +     struct irq_fwspec gic_data;
>> +     irq_hw_number_t hwirq;
>> +     int index, ret, i;
>> +
>> +     if (irq_data->param_count != 2)
>> +             return -EINVAL;
>> +
>> +     hwirq = irq_data->param[0];
>> +     dev_dbg(pc->dev, "%s irq %d, nr %d, hwirq %lu\n",
>> +                     __func__, irq, nr_irqs, hwirq);
>> +
>> +     for (i = 0; i < nr_irqs; i++) {
>> +             index = meson_map_gic_irq(domain, hwirq + i);
>> +             if (index < 0)
>> +                     return index;
>> +
>> +             irq_domain_set_hwirq_and_chip(domain, irq + i,
>> +                                           hwirq + i,
>> +                                           &meson_irq_chip,
>> +                                           pc);
>> +
>> +             gic_data.param_count = 3;
>> +             gic_data.fwnode = domain->parent->fwnode;
>> +             gic_data.param[0] = 0; /* SPI */
>> +             gic_data.param[1] = pc->gic_irqs[index];
>> +             gic_data.param[1] = IRQ_TYPE_EDGE_RISING;

Oh, this should be gic_data.param[2]. Just noticed.

> That feels quite wrong. Hardcoding the trigger like this and hoping for
> a set_type to set it right at a later time is just asking for trouble.
> Why can't you use the trigger type that has been provided by the
> interrupt descriptor?

In v2 I had the set of fwspec to track number and trigger type of the
IRQ, so it was straightforward. With this patch I have moved away from
that solution (as you suggested) and I'm using the 'amlogic,irqs-gpio'
parameter to track down the IRQ numbers (but not the trigger type).
It's the same solution we have in drivers/irqchip/irq-crossbar.c where
the trigger type is hardcoded in allocate_gic_irq().
If I need to save both the IRQ and the trigger type at this point I
wonder if it's better to go back to the set of fwspec or convert the
fwspec to of_phandle_args and save that.

>> +static int meson_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
>> +{
>> +     struct meson_domain *domain = to_meson_domain(chip);
>> +     struct meson_pinctrl *pc = domain->pinctrl;
>> +     struct meson_bank *bank;
>> +     struct irq_fwspec irq_data;
>> +     unsigned int hwirq, irq;
>> +
>> +     hwirq = domain->data->pin_base + offset;
>> +
>> +     if (meson_get_bank(domain, hwirq, &bank))
>> +             return -ENXIO;
>> +
>> +     irq_data.param_count = 2;
>> +     irq_data.param[0] = hwirq;
>> +
>> +     /* dummy. It will be changed later in meson_irq_set_type */
>> +     irq_data.param[1] = IRQ_TYPE_EDGE_RISING;
>
> Blah. Worse than I though... How do you end-up here? Why can't you
> obtain the corresponding of_phandle_args instead of making things up?

because I do not have a of_phandle. This is basically the .to_irq hook
of the gpio_chip. This code is being called programmatically from the
gpiolib. No DTS/OF involved here.

> This looks mad. Do you really need this?

Well, I'm open to any suggestion on how improve this mess.

-- 
Carlo Caione