[PATCH 2/2] memory: omap-gpmc: Add Kconfig option for debug
Hannes Schmelzer
Hannes.Schmelzer at br-automation.com
Wed Aug 26 23:25:57 PDT 2015
Hi Tony,
Did anyone test this changeset on some AM335x board?
Today I ran into trouble with that because:
The GPMC controller gets reseted on kernel boot due to the missing/removed
HWMOD_INIT_NO_RESET flag.
Primary this should not be a big problem, but on my board (maybe on all
AM335x) the GPMC doesn't behave as described in TRM.
Especially the GPMC_CONFIG register is not reset to 0h after reset,
instead it holds the value 0xa00 which is very strange because bit 10-31
are reserved.
Further this 0xa00 means that Bit9 (WAIT1PINPOLARITY) is set, exactly this
causes my system to stall on first access the connected NAND flash because
it never becomes ready due to the wrong wait pin polarity. Maybe others
dont't run into trouble because they may use WAIT0PIN, which one has it's
old polarity.
First approach was simply to write 0x0 to the GPMC_CONFIG register during
gpmc_probe function.
It solves the problem.
I also tried to issue some SYSRESET through GPMC registers without
success, same strange behavior.
What?s your thinking around that?
Best regards,
Hannes
linux-omap-owner at vger.kernel.org schrieb am 20.05.2015 23:21:03:
> Von: Tony Lindgren <tony at atomide.com>
> An: linux-omap at vger.kernel.org
> Kopie: linux-arm-kernel at lists.infradead.org, Brian Hutchinson
> <b.hutchman at gmail.com>, Paul Walmsley <paul at pwsan.com>, Roger Quadros
<rogerq at ti.com>
> Datum: 20.05.2015 23:37
> Betreff: [PATCH 2/2] memory: omap-gpmc: Add Kconfig option for debug
> Gesendet von: linux-omap-owner at vger.kernel.org
>
> We support decoding the bootloader values if DEBUG is defined.
> But we also need to change the struct omap_hwmod flags to have
> HWMOD_INIT_NO_RESET to avoid the GPMC being reset during the
> boot. Otherwise just the default timings will be displayed
> instead of the bootloader configured timings.
>
> This also allows us to clean up the various GPMC related
> hwmod flags. For debugging, we only need HWMOD_INIT_NO_RESET,
> and HWMOD_INIT_NO_IDLE is not needed.
>
> Cc: Brian Hutchinson <b.hutchman at gmail.com>
> Cc: Paul Walmsley <paul at pwsan.com>
> Cc: Roger Quadros <rogerq at ti.com>
> Signed-off-by: Tony Lindgren <tony at atomide.com>
> ---
> arch/arm/mach-omap2/omap_hwmod.h | 6 ++++++
> arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c | 12
++----------
> arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c | 3 ++-
> arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 12
++----------
> arch/arm/mach-omap2/omap_hwmod_44xx_data.c | 11
++---------
> arch/arm/mach-omap2/omap_hwmod_7xx_data.c | 4 ++--
> arch/arm/mach-omap2/omap_hwmod_81xx_data.c | 2 ++
> drivers/memory/Kconfig | 8 ++++++++
> drivers/memory/omap-gpmc.c | 6 +++---
> 9 files changed, 29 insertions(+), 35 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/omap_hwmod.h
b/arch/arm/mach-omap2/omap_hwmod.h
> index 9611c91..b5d27ec 100644
> --- a/arch/arm/mach-omap2/omap_hwmod.h
> +++ b/arch/arm/mach-omap2/omap_hwmod.h
> @@ -109,6 +109,12 @@ extern struct omap_hwmod_sysc_fields
omap_hwmod_sysc_type3;
>
> #define DEBUG_OMAPUART_FLAGS (HWMOD_INIT_NO_IDLE |
HWMOD_INIT_NO_RESET)
>
> +#ifdef CONFIG_OMAP_GPMC_DEBUG
> +#define DEBUG_OMAP_GPMC_HWMOD_FLAGS HWMOD_INIT_NO_RESET
> +#else
> +#define DEBUG_OMAP_GPMC_HWMOD_FLAGS 0
> +#endif
> +
> #if defined(CONFIG_DEBUG_OMAP2UART1)
> #undef DEBUG_OMAP2UART1_FLAGS
> #define DEBUG_OMAP2UART1_FLAGS DEBUG_OMAPUART_FLAGS
> diff --git a/arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c
b/arch/arm/
> mach-omap2/omap_hwmod_2xxx_ipblock_data.c
> index 8821b9d..6dcfd03 100644
> --- a/arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c
> +++ b/arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c
> @@ -762,16 +762,8 @@ struct omap_hwmod omap2xxx_gpmc_hwmod = {
> .name = "gpmc",
> .class = &omap2xxx_gpmc_hwmod_class,
> .main_clk = "gpmc_fck",
> - /*
> - * XXX HWMOD_INIT_NO_RESET should not be needed for this IP
> - * block. It is not being added due to any known bugs with
> - * resetting the GPMC IP block, but rather because any timings
> - * set by the bootloader are not being correctly programmed by
> - * the kernel from the board file or DT data.
> - * HWMOD_INIT_NO_RESET should be removed ASAP.
> - */
> - .flags = (HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET |
> - HWMOD_NO_IDLEST),
> + /* Skip reset for CONFIG_OMAP_GPMC_DEBUG for bootloader timings */
> + .flags = HWMOD_NO_IDLEST | DEBUG_OMAP_GPMC_HWMOD_FLAGS,
> .prcm = {
> .omap2 = {
> .prcm_reg_id = 3,
> diff --git a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c
b/arch/
> arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c
> index cabc569..ae0cb67 100644
> --- a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c
> +++ b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c
> @@ -668,7 +668,8 @@ struct omap_hwmod am33xx_gpmc_hwmod = {
> .name = "gpmc",
> .class = &am33xx_gpmc_hwmod_class,
> .clkdm_name = "l3s_clkdm",
> - .flags = (HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET),
> + /* Skip reset for CONFIG_OMAP_GPMC_DEBUG for bootloader timings */
> + .flags = DEBUG_OMAP_GPMC_HWMOD_FLAGS,
> .main_clk = "l3s_gclk",
> .prcm = {
> .omap4 = {
> diff --git a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
b/arch/arm/mach-omap2/
> omap_hwmod_3xxx_data.c
> index 4e8e93c..0ca4d3f 100644
> --- a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
> +++ b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
> @@ -2169,16 +2169,8 @@ static struct omap_hwmod omap3xxx_gpmc_hwmod = {
> .clkdm_name = "core_l3_clkdm",
> .mpu_irqs = omap3xxx_gpmc_irqs,
> .main_clk = "gpmc_fck",
> - /*
> - * XXX HWMOD_INIT_NO_RESET should not be needed for this IP
> - * block. It is not being added due to any known bugs with
> - * resetting the GPMC IP block, but rather because any timings
> - * set by the bootloader are not being correctly programmed by
> - * the kernel from the board file or DT data.
> - * HWMOD_INIT_NO_RESET should be removed ASAP.
> - */
> - .flags = (HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET |
> - HWMOD_NO_IDLEST),
> + /* Skip reset for CONFIG_OMAP_GPMC_DEBUG for bootloader timings */
> + .flags = HWMOD_NO_IDLEST | DEBUG_OMAP_GPMC_HWMOD_FLAGS,
> };
>
> /*
> diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
b/arch/arm/mach-omap2/
> omap_hwmod_44xx_data.c
> index f5e68a7..43eebf2 100644
> --- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
> +++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
> @@ -1188,15 +1188,8 @@ static struct omap_hwmod omap44xx_gpmc_hwmod = {
> .name = "gpmc",
> .class = &omap44xx_gpmc_hwmod_class,
> .clkdm_name = "l3_2_clkdm",
> - /*
> - * XXX HWMOD_INIT_NO_RESET should not be needed for this IP
> - * block. It is not being added due to any known bugs with
> - * resetting the GPMC IP block, but rather because any timings
> - * set by the bootloader are not being correctly programmed by
> - * the kernel from the board file or DT data.
> - * HWMOD_INIT_NO_RESET should be removed ASAP.
> - */
> - .flags = HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET,
> + /* Skip reset for CONFIG_OMAP_GPMC_DEBUG for bootloader timings */
> + .flags = DEBUG_OMAP_GPMC_HWMOD_FLAGS,
> .prcm = {
> .omap4 = {
> .clkctrl_offs = OMAP4_CM_L3_2_GPMC_CLKCTRL_OFFSET,
> diff --git a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
b/arch/arm/mach-omap2/
> omap_hwmod_7xx_data.c
> index 0e64c2f..a0411f3 100644
> --- a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
> +++ b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
> @@ -819,8 +819,8 @@ static struct omap_hwmod dra7xx_gpmc_hwmod = {
> .name = "gpmc",
> .class = &dra7xx_gpmc_hwmod_class,
> .clkdm_name = "l3main1_clkdm",
> - .flags = (HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET |
> - HWMOD_SWSUP_SIDLE),
> + /* Skip reset for CONFIG_OMAP_GPMC_DEBUG for bootloader timings */
> + .flags = HWMOD_SWSUP_SIDLE | DEBUG_OMAP_GPMC_HWMOD_FLAGS,
> .main_clk = "l3_iclk_div",
> .prcm = {
> .omap4 = {
> diff --git a/arch/arm/mach-omap2/omap_hwmod_81xx_data.c
b/arch/arm/mach-omap2/
> omap_hwmod_81xx_data.c
> index cab1eb6..c924137 100644
> --- a/arch/arm/mach-omap2/omap_hwmod_81xx_data.c
> +++ b/arch/arm/mach-omap2/omap_hwmod_81xx_data.c
> @@ -478,6 +478,8 @@ static struct omap_hwmod dm81xx_gpmc_hwmod = {
> .clkdm_name = "alwon_l3s_clkdm",
> .class = &dm81xx_gpmc_hwmod_class,
> .main_clk = "sysclk6_ck",
> + /* Skip reset for CONFIG_OMAP_GPMC_DEBUG for bootloader timings */
> + .flags = DEBUG_OMAP_GPMC_HWMOD_FLAGS,
> .prcm = {
> .omap4 = {
> .clkctrl_offs = DM816X_CM_ALWON_GPMC_CLKCTRL,
> diff --git a/drivers/memory/Kconfig b/drivers/memory/Kconfig
> index 868036f..8406c668 100644
> --- a/drivers/memory/Kconfig
> +++ b/drivers/memory/Kconfig
> @@ -49,6 +49,14 @@ config OMAP_GPMC
> interfacing to a variety of asynchronous as well as synchronous
> memory drives like NOR, NAND, OneNAND, SRAM.
>
> +config OMAP_GPMC_DEBUG
> + bool
> + depends on OMAP_GPMC
> + help
> + Enables verbose debugging mostly to decode the bootloader provided
> + timings. Enable this during development to configure devices
> + connected to the GPMC bus.
> +
> config MVEBU_DEVBUS
> bool "Marvell EBU Device Bus Controller"
> default y
> diff --git a/drivers/memory/omap-gpmc.c b/drivers/memory/omap-gpmc.c
> index 0e524a1..3a27a84 100644
> --- a/drivers/memory/omap-gpmc.c
> +++ b/drivers/memory/omap-gpmc.c
> @@ -403,7 +403,7 @@ static void gpmc_cs_bool_timings(int cs, const
struct
> gpmc_bool_timings *p)
> p->cycle2cyclediffcsen);
> }
>
> -#ifdef DEBUG
> +#ifdef CONFIG_OMAP_GPMC_DEBUG
> /**
> * get_gpmc_timing_reg - read a timing parameter and print DTS settings
for it.
> * @cs: Chip Select Region
> @@ -612,7 +612,7 @@ static int set_gpmc_timing_reg(int cs, int reg, int
> st_bit, int end_bit, int max
> }
>
> l = gpmc_cs_read_reg(cs, reg);
> -#ifdef DEBUG
> +#ifdef CONFIG_OMAP_GPMC_DEBUG
> pr_info(
> "GPMC CS%d: %-17s: %3d ticks, %3lu ns (was %3i ticks) %3d ns\n",
> cs, name, ticks, gpmc_get_clk_period(cs, cd) * ticks / 1000,
> @@ -767,7 +767,7 @@ int gpmc_cs_set_timings(int cs, const struct
gpmc_timings *t,
> GPMC_CONFIG1_CLKACTIVATIONTIME_MAX,
> clk_activation, GPMC_CD_FCLK);
>
> -#ifdef DEBUG
> +#ifdef CONFIG_OMAP_GPMC_DEBUG
> pr_info("GPMC CS%d CLK period is %lu ns (div %d)\n",
> cs, (div * gpmc_get_fclk_period()) / 1000, div);
> #endif
> --
> 2.1.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
More information about the linux-arm-kernel
mailing list