[PATCH-v3 2/2] regulator: 88pm800: Add support for configuration of dual phase on BUCK1

[Krzysztof Kozlowski]

On 24.08.2015 21:40, Vaibhav Hiremath wrote:
> 88PM860 device supports dual phase mode on BUCK1 output.
> In normal usecase, BUCK1A and BUCK1B operates independently with 3A
> capacity. And they both can work as a dual phase providing 6A capacity.
> 
> This patch updates the regulator driver to read the respective
> DT property and enable dual-phase mode on BUCK1.
> Note that if dual phase mode is enabled, then BUCK1B will not be
> registered to the regulator framework and the current capacity of
> BUCK1(A) would be set to 6A [3A of BUCK1A + 3A of BUCK1B].
> 
> Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath at linaro.org>
> ---
>  drivers/regulator/88pm800.c | 40 ++++++++++++++++++++++++++++++++++++++++
>  include/linux/mfd/88pm80x.h |  3 +++
>  2 files changed, 43 insertions(+)
> 
> diff --git a/drivers/regulator/88pm800.c b/drivers/regulator/88pm800.c
> index 365a154..7aca6d17 100644
> --- a/drivers/regulator/88pm800.c
> +++ b/drivers/regulator/88pm800.c
> @@ -267,6 +267,37 @@ static struct pm800_regulator_info pm860_regulator_info[] = {
>  	PM800_LDO(ldo20, LDO20, LDO_ENA1_3, 3, 10000, ldo_volt_table2),
>  };
>  
> +static int pm800_regulator_init(struct platform_device *pdev,
> +		struct pm800_regulator_info *info)
> +{
> +	struct pm800_regulators *pm800_data = platform_get_drvdata(pdev);
> +	struct pm80x_chip *chip = pm800_data->chip;
> +	int ret = 0;
> +
> +	/* Currently only supported on 88pm860 device */
> +	if (chip->type != CHIP_PM860)
> +		return 0;
> +
> +	if (of_property_read_bool(pdev->dev.of_node,
> +				"marvell,88pm860-buck1-dualphase-en")) {
> +		/* Update the constraint  to [3A (BUCK1A) + 3A (BUCK1B)] */
> +		info[PM800_ID_BUCK1].max_ua = 6000000;
> +		/* Remove BUCK1B from the list, as we are in dual phase mode */
> +		memset(&info[PM800_ID_BUCK1B], 0, sizeof(*info));
> +		/* Enable dual phase mode */
> +		ret = regmap_update_bits(chip->subchip->regmap_power,
> +					PM860_BUCK1_MISC,
> +					BUCK1_DUAL_PHASE_SEL,
> +					BUCK1_DUAL_PHASE_SEL);
> +		if (ret) {
> +			dev_err(chip->dev, "failed to set dual-pase mode %d\n", ret);
> +			return ret;
> +		}
> +	}
> +
> +	return ret;
> +}
> +
>  static int pm800_regulator_probe(struct platform_device *pdev)
>  {
>  	struct pm80x_chip *chip = dev_get_drvdata(pdev->dev.parent);
> @@ -311,11 +342,20 @@ static int pm800_regulator_probe(struct platform_device *pdev)
>  		return -ENODEV;
>  	}
>  
> +	ret = pm800_regulator_init(pdev, info);
> +	if (ret) {
> +		dev_err(&pdev->dev, "failed to init 88pm800 regulator device\n");
> +		return ret;
> +	}
> +
>  	config.dev = chip->dev;
>  	config.regmap = pm800_data->map;
>  	for (i = 0; i < PM800_ID_RG_MAX; i++) {
>  		struct regulator_dev *regulator;
>  
> +		if (!info[i].desc.name)
> +			continue;

How the driver was working without this on 88PM800? There is a gap in
pm800_regulator_info - three regulators are not set.

The patch itself looks good
Reviewed-by: Krzysztof Kozlowski <k.kozlowski at samsung.com>

Best regards,
Krzysztof