[PATCH v2 2/5] Documentation: Detail permitted DT properties for the imx6ul_tsc

[Chen Bough]

Hi Markus,

> -----Original Message-----
> From: Markus Pargmann [mailto:mpa at pengutronix.de]
> Sent: Wednesday, August 19, 2015 1:55 PM
> To: Chen Haibo-B51421
> Cc: robh+dt at kernel.org; pawel.moll at arm.com; mark.rutland at arm.com;
> ijc+devicetree at hellion.org.uk; galak at codeaurora.org; shawnguo at kernel.org;
> kernel at pengutronix.de; linux at arm.linux.org.uk; dmitry.torokhov at gmail.com;
> devicetree at vger.kernel.org; sbranden at broadcom.com; arnd at arndb.de;
> mchehab at osg.samsung.com; christian.gmeiner at gmail.com;
> scott.liu at emc.com.tw; linux-kernel at vger.kernel.org; hdegoede at redhat.com;
> jonathar at broadcom.com; benjamin.tissoires at redhat.com;
> hans.verkuil at cisco.com; hadess at hadess.net; linux-input at vger.kernel.org;
> geert at linux-m68k.org; sebastien.szymanski at armadeus.com;
> mamlinav at gmail.com; linux-arm-kernel at lists.infradead.org
> Subject: Re: [PATCH v2 2/5] Documentation: Detail permitted DT properties
> for the imx6ul_tsc
> 
> Hi,
> 
> On Tue, Jul 28, 2015 at 05:58:38PM +0800, Haibo Chen wrote:
> > Here we apply required documentation for the imx6ul touch screen
> > controller driver which describe available properties and how to use
> > them.
> >
> > Signed-off-by: Haibo Chen <haibo.chen at freescale.com>
> > ---
> >  .../bindings/input/touchscreen/imx6ul_tsc.txt      | 36
> ++++++++++++++++++++++
> >  1 file changed, 36 insertions(+)
> >  create mode 100644
> > Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt
> >
> > diff --git
> > a/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt
> > b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt
> > new file mode 100644
> > index 0000000..ac41c32
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.t
> > +++ xt
> > @@ -0,0 +1,36 @@
> > +* Freescale i.MX6UL Touch Controller
> > +
> > +Required properties:
> > +- compatible: must be "fsl,imx6ul-tsc".
> > +- reg: this touch controller address and the ADC2 address.
> 
> This suggests that this driver is using a unit ADC2. Which also means
> that there are more than one ADC which are probably identical?
> 
> Shouldn't these ADCs be properly described by their own device nodes
> instead of these two register ranges, two interrupts and two clocks?
> 
> Is 'ADC2' usable without tsc? Then ADC1/ADC2 should perhaps get a proper
> IIO driver.

For i.MX6UL, there are two ADC. ADC1 is a normal ADC, and ADC2 can only works for
TSC, the channels of ADC2 are connected to TSC directly. TSC and ADC2 should work
together as a touch screen controller. 

For ADC1, it share the driver vf610_adc.c (drivers/iio/adc/vf610_adc.c). 

Best Regards

Haibo 
 
> 
> Unfortunately I don't have the reference manual to have a look how this
> all works.
> 
> Best regards,
> 
> Markus
> 
> > +- interrupts: the interrupt of this touch controller and ADC2.
> > +- clocks: the root clock of touch controller and ADC2.
> > +- clock-names; must be "tsc" and "adc".
> > +- xnur-gpio: the X- gpio this controller connect to.
> > +  This xnur-gpio returns to high once the finger leave the touch
> > +screen (The
> > +  last touch event the touch controller capture).
> > +
> > +Optional properties:
> > +- measure-delay-time: the value of measure delay time.
> > +  Before X-axis or Y-axis measurement, the screen need some time
> > +before
> > +  even potential distribution ready.
> > +  This value depends on the touch screen.
> > +- pre-charge-time: the touch screen need some time to precharge.
> > +  This value depends on the touch screen.
> > +
> > +Example:
> > +	tsc: tsc at 02040000 {
> > +		compatible = "fsl,imx6ul-tsc";
> > +		reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
> > +		interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
> > +			     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
> > +		clocks = <&clks IMX6UL_CLK_IPG>,
> > +			 <&clks IMX6UL_CLK_ADC2>;
> > +		clock-names = "tsc", "adc";
> > +		pinctrl-names = "default";
> > +		pinctrl-0 = <&pinctrl_tsc>;
> > +		xnur-gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>;
> > +		measure-delay-time = <0xfff>;
> > +		pre-charge-time = <0xffff>;
> > +		status = "okay";
> > +	};
> > --
> > 1.9.1
> >
> >
> >
> 
> --
> Pengutronix e.K.                           |
> |
> Industrial Linux Solutions                 | http://www.pengutronix.de/
> |
> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0
> |
> Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555
> |