[PATCH v2 03/21] ARM: pxa: magician: Fix comments, debug functions and print strings

[Robert Jarzmik]

Petr Cvek <petr.cvek at tul.cz> writes:

> Fix comments, debug functions and print strings. Rename backlight
> structures to be more specific.
>
> Signed-off-by: Petr Cvek <petr.cvek at tul.cz>
> ---
>  arch/arm/mach-pxa/magician.c | 121 +++++++++++++++++++++++++++++++------------
>  1 file changed, 89 insertions(+), 32 deletions(-)
>
> diff --git a/arch/arm/mach-pxa/magician.c b/arch/arm/mach-pxa/magician.c
> index 9e8698a..57da133 100644
> --- a/arch/arm/mach-pxa/magician.c
> +++ b/arch/arm/mach-pxa/magician.c
> @@ -11,6 +11,46 @@
>   * it under the terms of the GNU General Public License version 2 as
>   * published by the Free Software Foundation.
>   *
> + *
> + * NOTICE MDA Compact (T-mobile XDA) facts:
> + *   On "LCD type = 1, system_rev = 2" (0x3a in CPLD)
> + * Samsung LTP280QV - valid LCD init sequence sequence:
> + *   powerup: Vdigital->Vanalog->gate Voff->gate Von->data enable
> + *   powerdown: data disable->gate Von->gate Voff->Vanalog->Vdigital
> + * Measured on PCB:
> + *   GPIO106
> + *     Affects VOFF, VON and other voltages
> + *     Probably main reset pin for DC-DC converter
> + *   GPIO75
> + *     Must be AF0+OUT (WM leaves it to AF2+OUT), not LCD signal
> + *     GPIO106 works only when GPIO75 is high (DC-DC power enable?)
> + *     After LCD powerup, value is irrelevant
> + *   GPIO104
> + *     LCD VOFF (gate off voltage)
> + *   GPIO105
> + *     LCD VON (gate on voltage)
> + * FFUART (/dev/ttyS0) WM: 38400,8,n,1,crtscts (GSM data?)
> + * BTUART (/dev/ttyS1) WM: 115200,8,n,1,crtscts (GSM AT commands)
> + *   Use a HTC line discipline: 0x02 channel(==0x16) data 0x02
> + * EGPIO(CPLD) should be always present (controls "all" supply power)
> + *   For rootfs on MMC/SD: EGPIO module controls card power (in kernel)
> + * cpu-freq often freeze platform (errata?, use userspace gov)
> + * Do not use YUV420, (erratum E24) causes LCD hang (forever)
> + * Many GSM related pins are unknown
> + * gpio-rc-recv probably require lowpass filter (sw is OK)
> + * TODO EGPIO_MAGICIAN_IR_RECEIVE_SHUTDOWN
> + * FIXME AC charging blocks IrDA
> + * Unimplemented blocking of camera+power+reset, reset and door open reset
> + *   Registers: htc-pasic3.h (but blocks charging too)
> + * Other PXA machines have wait_for_sync for ADS7846 (during LCD refresh)
> + * pda-power has not optimal charging (accu can be bloated)
> + * TODO Current switching works? Is gpio-regulator/bq24022 required?
I think you can ask Philip, he's the maintainer after all ...

> + * pdata supports alternative drivers (mutually exclusive modules)
> + *   i2c-pxa vs i2c-gpio (SCCB)
> + *   pwm_bl vs gpio_backlight
> + *   pxa27x_udc vs phy-gpio-vbus-usb
> + *   physmap-flash vs pxa2xx-flash

Okay, this chunk is nice documentation, but not code ...
I'd rather have it in : Documentation/arm/pxa/magician.txt or something like
that.

> @@ -120,11 +160,12 @@ static unsigned long magician_pin_config[] __initdata = {
>  };
>  
>  /*
> - * IRDA
> + * IrDA
>   */
>  
>  static struct pxaficp_platform_data magician_ficp_info = {
>  	.gpio_pwdown		= GPIO83_MAGICIAN_nIR_EN,
> +	/* TODO test with FIR dongle */
I don't like this comment. I was not there before, so let it be. You know there
remains a TODO, I know ... but you can cunningly slip it in the commit message.

Cheers.

-- 
Robert