[PATCH] ARM: OMAP: irqdomain_hierarchy: fix arm gic irq type configuration

[Marc Zyngier]

On Tue, 11 Aug 2015 13:16:13 +0100
Grygorii Strashko <grygorii.strashko at ti.com> wrote:

> On 08/11/2015 02:24 PM, Marc Zyngier wrote:
> > On Tue, 11 Aug 2015 10:25:47 +0100
> > Grygorii Strashko <grygorii.strashko at ti.com> wrote:
> >
> > Hi Grygorii,
> >
> >> It's observed that ARM GIC IRQ triggering type is not configured
> >> properly when IRQ is routed through IRQ domains hierarchy and
> >> system started using DT. As result, system will start using default
> >> ARM GIC configuration, ignore DT IRQ type configuration,
> >> and value of desc->irq_data.state_use_accessors = 0.
> >>
> >> In case of TI OMAP the following IRQ hierarchy is defined:
> >> ARM GIC <- OMAP wakeupgen <- TI CBAR
> >>
> >> Failed call chain:
> >>   irq_create_of_mapping
> >>   irq_set_irq_type
> >>   __irq_set_trigger
> >>   if (!chip || !chip->irq_set_type) {
> >>      return 0; <- return here
> >>   }
> >>   CBAR has no .irq_set_type() defined and, so, IRQ triggering
> >>   configuration will not be propagated to parent IRQ domain.
> >>
> >> Hence, fix it by introducing irq_chip_set_type_parent(), in the
> >> same manner as irq_chip_set_wake_parent(), and use it for IRQ
> >> triggering type propagation to the parent IRQ domain in
> >> irq-crossbar and omap-wakeupgen.
> >>
> >> / # cat /proc/interrupts -- before
> >> 230:          0          0      CBAR  30 Edge    -00000000  48051000.gpio
> >> 263:          0          0      CBAR 116 Edge    -00000000  48053000.gpio
> >> 296:        246          0      CBAR  67 Edge    -00000000  OMAP UART0
> >> 311:        341          0      CBAR  51 Edge    -00000000  48070000.i2c
> >> 312:          3          0      CBAR  52 Edge    -00000000  48072000.i2c
> >> 313:          0          0      CBAR  56 Edge    -00000000  48060000.i2c
> >> 314:        255          0      CBAR  78 Edge    -00000000  mmc0
> >> 315:         40          0      CBAR  81 Edge    -00000000  mmc1
> >> 316:         13          0      CBAR  91 Edge    -00000000  mmc2
> >> 320:          0          0      CBAR  49 Edge    -00000000  4a140000.sata
> >> 324:          0          0      CBAR   1 Edge    -00000000  48078000.elm
> >> 325:          0          0      CBAR  15 Edge    -00000000  gpmc
> >> 333:          0          0      CBAR 335 Edge    -00000000  48484000.ethernet
> >> 334:          0          0      CBAR 336 Edge    -00000000  48484000.ethernet
> >> 415:          0          0   pcf857x   2 Edge    -00000000  btnUser1
> >> 416:          0          0   pcf857x   3 Edge    -00000000  btnUser2
> >> 445:          0          0   pinctrl 992 Edge    -00010000  4806a000.seria
> >>
> >> / # cat /proc/interrupts -- after
> >> 230:          0          0      CBAR  30 Level   -00002004  48051000.gpio
> >> 263:          0          0      CBAR 116 Level   -00002004  48053000.gpio
> >> 296:        567          0      CBAR  67 Level   -00002004  OMAP UART0
> >> 311:        363          0      CBAR  51 Level   -00002004  48070000.i2c
> >> 312:          3          0      CBAR  52 Level   -00002004  48072000.i2c
> >> 313:          0          0      CBAR  56 Level   -00002004  48060000.i2c
> >> 314:        197          0      CBAR  78 Level   -00002004  mmc0
> >> 315:         40          0      CBAR  81 Level   -00002004  mmc1
> >> 316:         13          0      CBAR  91 Level   -00002004  mmc2
> >> 320:          0          0      CBAR  49 Level   -00002004  4a140000.sata
> >> 324:          0          0      CBAR   1 Level   -00002004  48078000.elm
> >> 325:          0          0      CBAR  15 Level   -00002004  gpmc
> >> 333:          0          0      CBAR 335 Level   -00002004  48484000.ethernet
> >> 334:          0          0      CBAR 336 Level   -00002004  48484000.ethernet
> >> 415:          0          0   pcf857x   2 Edge    -00000000  btnUser1
> >> 416:          4          2   pcf857x   3 Edge    -00000000  btnUser2
> >> 445:          0          0   pinctrl 992 Edge    -00010000  4806a000.serial
> >>
> >> Fixes: 783d31863fb8 ('irqchip: crossbar: Convert dra7 crossbar to stacked domains')
> >> Signed-off-by: Grygorii Strashko <grygorii.strashko at ti.com>
> >> ---
> >> Hi All,
> >>
> >> I can split patch if required and overall solution acceptable.
> >
> > This looks good to me. Please repost it after splitting it in two
> > patches.
> 
> just to clarify - Do you want to see two or three patches?
> 
> 2) or 3) arch/arm/mach-omap2/omap-wakeupgen.c |  1 +
> 2) drivers/irqchip/irq-crossbar.c       |  1 +
> 1) include/linux/irq.h                  |  1 +
> 1) kernel/irq/chip.c                    | 16 ++++++++++++++++

Ah, I forgot wakeupgen lived in the omap-specific directory.

Please cut it in 3 then (generic implementation, crossbar and
wakeupgen).

Thanks,

	M.


-- 
Jazz is not dead. It just smells funny.