[PATCH v4 1/6] mmc: sdhci-esdhc-imx: add imx7d support and support HS400
Chen Bough
Haibo.Chen at freescale.com
Fri Aug 7 02:53:01 PDT 2015
> -----Original Message-----
> From: Dong Aisheng [mailto:aisheng.dong at freescale.com]
> Sent: Friday, August 07, 2015 3:39 PM
> To: Chen Haibo-B51421
> Cc: robh+dt at kernel.org; pawel.moll at arm.com; mark.rutland at arm.com;
> ijc+devicetree at hellion.org.uk; galak at codeaurora.org; shawnguo at kernel.org;
> kernel at pengutronix.de; linux at arm.linux.org.uk; ulf.hansson at linaro.org;
> johan.derycke at barco.com; mkl at pengutronix.de; Estevam Fabio-R49496; Dong
> Aisheng-B29396; devicetree at vger.kernel.org; linux-kernel at vger.kernel.org;
> linux-arm-kernel at lists.infradead.org; linux-mmc at vger.kernel.org
> Subject: Re: [PATCH v4 1/6] mmc: sdhci-esdhc-imx: add imx7d support and
> support HS400
>
> On Wed, Aug 05, 2015 at 06:38:37PM +0800, Haibo Chen wrote:
> > The imx7d usdhc is derived from imx6sx, the difference is that imx7d
> > support HS400.
> >
> > So introduce a new compatible string for imx7d and add HS400 support
> > for imx7d usdhc.
> >
> > Signed-off-by: Haibo Chen <haibo.chen at freescale.com>
> > ---
> > drivers/mmc/host/sdhci-esdhc-imx.c | 81
> > ++++++++++++++++++++++++++++++++++++++
> > 1 file changed, 81 insertions(+)
> >
> > diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c
> > b/drivers/mmc/host/sdhci-esdhc-imx.c
> > index c6b9f64..48f009c 100644
> > --- a/drivers/mmc/host/sdhci-esdhc-imx.c
> > +++ b/drivers/mmc/host/sdhci-esdhc-imx.c
> > @@ -44,6 +44,7 @@
> > #define ESDHC_MIX_CTRL_EXE_TUNE (1 << 22)
> > #define ESDHC_MIX_CTRL_SMPCLK_SEL (1 << 23)
> > #define ESDHC_MIX_CTRL_FBCLK_SEL (1 << 25)
> > +#define ESDHC_MIX_CTRL_HS400_EN (1 << 26)
> > /* Bits 3 and 6 are not SDHCI standard definitions */
> > #define ESDHC_MIX_CTRL_SDHCI_MASK 0xb7
> > /* Tuning bits */
> > @@ -60,6 +61,16 @@
> > #define ESDHC_TUNE_CTRL_MIN 0
> > #define ESDHC_TUNE_CTRL_MAX ((1 << 7) - 1)
> >
> > +/* strobe dll register */
> > +#define ESDHC_STROBE_DLL_CTRL 0x70
> > +#define ESDHC_STROBE_DLL_CTRL_ENABLE (1 << 0)
> > +#define ESDHC_STROBE_DLL_CTRL_RESET (1 << 1)
> > +#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT 3
> > +
> > +#define ESDHC_STROBE_DLL_STATUS 0x74
> > +#define ESDHC_STROBE_DLL_STS_REF_LOCK (1 << 1)
> > +#define ESDHC_STROBE_DLL_STS_SLV_LOCK 0x1
> > +
> > #define ESDHC_TUNING_CTRL 0xcc
> > #define ESDHC_STD_TUNING_EN (1 << 24)
> > /* NOTE: the minimum valid tuning start tap for mx6sl is 1 */ @@
> > -120,6 +131,11 @@
> > #define ESDHC_FLAG_ERR004536 BIT(7)
> > /* The IP supports HS200 mode */
> > #define ESDHC_FLAG_HS200 BIT(8)
> > +/* The IP supports HS400 mode */
> > +#define ESDHC_FLAG_HS400 BIT(9)
> > +
> > +/* A higher clock ferquency than this rate requires strobell dll
> control */
> > +#define ESDHC_STROBE_DLL_CLK_FREQ 100000000
> >
> > struct esdhc_soc_data {
> > u32 flags;
> > @@ -156,6 +172,12 @@ static struct esdhc_soc_data usdhc_imx6sx_data = {
> > | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200, };
> >
> > +static struct esdhc_soc_data usdhc_imx7d_data = {
> > + .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
> > + | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
> > + | ESDHC_FLAG_HS400,
> > +};
> > +
> > struct pltfm_imx_data {
> > u32 scratchpad;
> > struct pinctrl *pinctrl;
> > @@ -199,6 +221,7 @@ static const struct of_device_id imx_esdhc_dt_ids[]
> = {
> > { .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, },
> > { .compatible = "fsl,imx6sl-usdhc", .data = &usdhc_imx6sl_data, },
> > { .compatible = "fsl,imx6q-usdhc", .data = &usdhc_imx6q_data, },
> > + { .compatible = "fsl,imx7d-usdhc", .data = &usdhc_imx7d_data, },
> > { /* sentinel */ }
> > };
> > MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids); @@ -274,6 +297,9 @@ static
> > u32 esdhc_readl_le(struct sdhci_host *host, int reg)
> > val = SDHCI_SUPPORT_DDR50 | SDHCI_SUPPORT_SDR104
> > | SDHCI_SUPPORT_SDR50
> > | SDHCI_USE_SDR50_TUNING;
> > +
> > + if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
> > + val |= SDHCI_SUPPORT_HS400;
> > }
> > }
> >
> > @@ -774,6 +800,7 @@ static int esdhc_change_pinstate(struct sdhci_host
> *host,
> > break;
> > case MMC_TIMING_UHS_SDR104:
> > case MMC_TIMING_MMC_HS200:
> > + case MMC_TIMING_MMC_HS400:
> > pinctrl = imx_data->pins_200mhz;
> > break;
> > default:
> > @@ -784,6 +811,44 @@ static int esdhc_change_pinstate(struct sdhci_host
> *host,
> > return pinctrl_select_state(imx_data->pinctrl, pinctrl); }
> >
> > +/*
> > + * For HS400 eMMC, there is a data_strobe line, this signal is
> > +generated
> > + * by the device and used for data output and CRC status response
> > +output
> > + * in HS400 mode. The frequency of this signal follows the frequency
> > +of
> > + * CLK generated by host. Host receive the data which is aligned to
> > +the
> > + * edge of data_strobe line. Due to the time delay between CLK line
> > +and
> > + * data_strobe line, if the delay time is larger than one clock
> > +cycle,
> > + * then CLK and data_strobe line will misaligned, read error shows up.
> > + * So when the CLK is higher than 100MHz, each clock cycle is short
> > +enough,
> > + * host should config the delay target.
> > + */
> > +static void esdhc_set_strobe_dll(struct sdhci_host *host) {
> > + u32 v;
> > +
> > + if (host->mmc->actual_clock > ESDHC_STROBE_DLL_CLK_FREQ) {
> > + /* force a reset on strobe dll */
> > + writel(ESDHC_STROBE_DLL_CTRL_RESET,
> > + host->ioaddr + ESDHC_STROBE_DLL_CTRL);
> > + /*
> > + * enable strobe dll ctrl and adjust the delay target
> > + * for the uSDHC loopback read clock
> > + */
> > + v = ESDHC_STROBE_DLL_CTRL_ENABLE |
> > + (7 << ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT);
> > + writel(v, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
> > + /* wait 1us to make sure strobe dll status register stable */
> > + udelay(1);
> > + v = readl(host->ioaddr + ESDHC_STROBE_DLL_STATUS);
> > + if (!(v & ESDHC_STROBE_DLL_STS_REF_LOCK))
> > + dev_warn(mmc_dev(host->mmc),
> > + "warning! HS400 strobe DLL status REF not
> lock!\n");
> > + if (!(v & ESDHC_STROBE_DLL_STS_SLV_LOCK))
> > + dev_warn(mmc_dev(host->mmc),
> > + "warning! HS400 strobe DLL status SLV not
> lock!\n");
> > + }
> > +}
> > +
> > static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned
> > timing) {
> > struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); @@ -795,7
> > +860,13 @@ static void esdhc_set_uhs_signaling(struct sdhci_host *host,
> unsigned timing)
> > case MMC_TIMING_UHS_SDR25:
> > case MMC_TIMING_UHS_SDR50:
> > case MMC_TIMING_UHS_SDR104:
> > + break;
> > case MMC_TIMING_MMC_HS200:
> > + /* disable ddr mode and disable HS400 mode */
> > + writel(readl(host->ioaddr + ESDHC_MIX_CTRL) &
> > + ~(ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN),
> > + host->ioaddr + ESDHC_MIX_CTRL);
> > + imx_data->is_ddr = 0;
>
> Can you please explain why need above code?
> Any issues if not do it?
>
> Regards
> Dong Aisheng
[haibo] currently, mmc core code use mmc_retune before every request,
and in mmc_retune, for eMMC, if the chip is in HS400 mode, firstly,
the code use mmc_hs400_to_hs200() to change the emmc chip work in
HS200 mode, and execute the tuning, and then use mmc_hs200_to_hs400()
to make the emmc chip work back in HS400 mode.
Without the above code, when change to hs200 mode from hs400 mode, our
host still enable ddr mode and enable hs400 mode, which is wrong.
So add the code here.
>
> > break;
> > case MMC_TIMING_UHS_DDR50:
> > case MMC_TIMING_MMC_DDR52:
> > @@ -813,6 +884,13 @@ static void esdhc_set_uhs_signaling(struct
> sdhci_host *host, unsigned timing)
> > writel(v, host->ioaddr + ESDHC_DLL_CTRL);
> > }
> > break;
> > + case MMC_TIMING_MMC_HS400:
> > + writel(readl(host->ioaddr + ESDHC_MIX_CTRL) |
> > + ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN,
> > + host->ioaddr + ESDHC_MIX_CTRL);
> > + imx_data->is_ddr = 1;
> > + esdhc_set_strobe_dll(host);
> > + break;
> > }
> >
> > esdhc_change_pinstate(host, timing); @@ -1100,6 +1178,9 @@ static
> > int sdhci_esdhc_imx_probe(struct platform_device *pdev)
> > if (imx_data->socdata->flags & ESDHC_FLAG_ERR004536)
> > host->quirks |= SDHCI_QUIRK_BROKEN_ADMA;
> >
> > + if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
> > + host->quirks2 |= SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400;
> > +
> > if (of_id)
> > err = sdhci_esdhc_imx_probe_dt(pdev, host, imx_data);
> > else
> > --
> > 1.9.1
> >
More information about the linux-arm-kernel
mailing list