[PATCH 1/2] dt-bindings: Add pxa1928 clock binding

[Rob Herring]

This adds the clock binding documentation for the Marvell PXA1928 SOC.
The PXA1928 has 3 clock control blocks for different subsystems of the
chip.

Signed-off-by: Rob Herring <robh at kernel.org>
Cc: Pawel Moll <pawel.moll at arm.com>
Cc: Mark Rutland <mark.rutland at arm.com>
Cc: Ian Campbell <ijc+devicetree at hellion.org.uk>
Cc: Kumar Gala <galak at codeaurora.org>
---
 .../devicetree/bindings/clock/marvell,pxa1928.txt  | 21 ++++++++
 include/dt-bindings/clock/marvell,pxa1928.h        | 57 ++++++++++++++++++++++
 2 files changed, 78 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/marvell,pxa1928.txt
 create mode 100644 include/dt-bindings/clock/marvell,pxa1928.h

diff --git a/Documentation/devicetree/bindings/clock/marvell,pxa1928.txt b/Documentation/devicetree/bindings/clock/marvell,pxa1928.txt
new file mode 100644
index 0000000..809c5a2
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/marvell,pxa1928.txt
@@ -0,0 +1,21 @@
+* Marvell PXA1928 Clock Controllers
+
+The PXA1928 clock subsystem generates and supplies clock to various
+controllers within the PXA1928 SoC. The PXA1928 contains 3 clock controller
+blocks called APMU, MPMU, and APBC roughly corresponding to internal buses.
+
+Required Properties:
+
+- compatible: should be one of the following.
+  - "marvell,pxa1928-apmu" - APMU controller compatible
+  - "marvell,pxa1928-mpmu" - MPMU controller compatible
+  - "marvell,pxa1928-apbc" - APBC controller compatible
+- reg: physical base address of the clock controller and length of memory mapped
+  region.
+- #clock-cells: should be 1.
+- #reset-cells: should be 1.
+
+Each clock is assigned an identifier and client nodes use the clock controller
+phandle and this identifier to specify the clock which they consume.
+
+All these identifiers can be found in <dt-bindings/clock/marvell,pxa1928.h>.
diff --git a/include/dt-bindings/clock/marvell,pxa1928.h b/include/dt-bindings/clock/marvell,pxa1928.h
new file mode 100644
index 0000000..c393ca2
--- /dev/null
+++ b/include/dt-bindings/clock/marvell,pxa1928.h
@@ -0,0 +1,57 @@
+#ifndef __DTS_MARVELL_PXA1928_CLOCK_H
+#define __DTS_MARVELL_PXA1928_CLOCK_H
+
+/*
+ * Clock ID values here correspond to the control register offset/4.
+ */
+
+/* apb periphrals */
+#define PXA1928_CLK_RTC			0
+#define PXA1928_CLK_TWSI0		1
+#define PXA1928_CLK_TWSI1		2
+#define PXA1928_CLK_TWSI2		3
+#define PXA1928_CLK_TWSI3		4
+#define PXA1928_CLK_OWIRE		5
+#define PXA1928_CLK_KPC			6
+#define PXA1928_CLK_TB_ROTARY		7
+#define PXA1928_CLK_SW_JTAG		8
+#define PXA1928_CLK_TIMER1		9
+#define PXA1928_CLK_UART0		0xb
+#define PXA1928_CLK_UART1		0xc
+#define PXA1928_CLK_UART2		0xd
+#define PXA1928_CLK_GPIO		0xe
+#define PXA1928_CLK_PWM0		0xf
+#define PXA1928_CLK_PWM1		0x10
+#define PXA1928_CLK_PWM2		0x11
+#define PXA1928_CLK_PWM3		0x12
+#define PXA1928_CLK_SSP0		0x13
+#define PXA1928_CLK_SSP1		0x14
+#define PXA1928_CLK_SSP2		0x15
+
+#define PXA1928_CLK_TWSI4		0x1f
+#define PXA1928_CLK_TWSI5		0x20
+#define PXA1928_CLK_UART3		0x22
+#define PXA1928_CLK_THSENS_GLOB		0x24
+#define PXA1928_CLK_THSENS_CPU		0x26
+#define PXA1928_CLK_THSENS_VPU		0x27
+#define PXA1928_CLK_THSENS_GC		0x28
+#define PXA1928_APBC_NR_CLKS		0x30
+
+
+/* axi periphrals */
+#define PXA1928_CLK_SDH0		0x15
+#define PXA1928_CLK_SDH1		0x16
+#define PXA1928_CLK_USB			0x17
+#define PXA1928_CLK_NAND		0x18
+#define PXA1928_CLK_DMA			0x19
+
+#define PXA1928_CLK_SDH2		0x3a
+#define PXA1928_CLK_SDH3		0x3b
+#define PXA1928_CLK_HSIC		0x3e
+#define PXA1928_CLK_SDH4		0x57
+#define PXA1928_CLK_GC3D		0x5d
+#define PXA1928_CLK_GC2D		0x5f
+
+#define PXA1928_APMU_NR_CLKS		0x60
+
+#endif
-- 
2.1.0