[PATCH v3 05/11] ARM: dts: exynos4: Use labels for overriding nodes in Trats
Krzysztof Kozlowski
k.kozlowski.k at gmail.com
Fri Apr 17 06:47:13 PDT 2015
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k at gmail.com>
---
arch/arm/boot/dts/exynos4210-trats.dts | 592 ++++++++++++++++-----------------
1 file changed, 296 insertions(+), 296 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4210-trats.dts b/arch/arm/boot/dts/exynos4210-trats.dts
index 32c5fd8f6269..98f3ce65cb9a 100644
--- a/arch/arm/boot/dts/exynos4210-trats.dts
+++ b/arch/arm/boot/dts/exynos4210-trats.dts
@@ -89,42 +89,6 @@
};
};
- hsotg at 12480000 {
- vusb_d-supply = <&vusb_reg>;
- vusb_a-supply = <&vusbdac_reg>;
- dr_mode = "peripheral";
- status = "okay";
- };
-
- sdhci_emmc: sdhci at 12510000 {
- bus-width = <8>;
- non-removable;
- pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>;
- pinctrl-names = "default";
- vmmc-supply = <&vemmc_reg>;
- status = "okay";
- };
-
- exynos-usbphy at 125B0000 {
- status = "okay";
- };
-
- serial at 13800000 {
- status = "okay";
- };
-
- serial at 13810000 {
- status = "okay";
- };
-
- serial at 13820000 {
- status = "okay";
- };
-
- serial at 13830000 {
- status = "okay";
- };
-
gpio-keys {
compatible = "gpio-keys";
@@ -158,201 +122,6 @@
};
};
- i2c at 13890000 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-slave-addr = <0x10>;
- samsung,i2c-max-bus-freq = <400000>;
- pinctrl-0 = <&i2c3_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- mms114-touchscreen at 48 {
- compatible = "melfas,mms114";
- reg = <0x48>;
- interrupt-parent = <&gpx0>;
- interrupts = <4 2>;
- x-size = <720>;
- y-size = <1280>;
- avdd-supply = <&tsp_reg>;
- vdd-supply = <&tsp_reg>;
- };
- };
-
- i2c at 138B0000 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-slave-addr = <0x10>;
- samsung,i2c-max-bus-freq = <100000>;
- pinctrl-0 = <&i2c5_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- max8997_pmic at 66 {
- compatible = "maxim,max8997-pmic";
-
- reg = <0x66>;
-
- max8997,pmic-buck1-uses-gpio-dvs;
- max8997,pmic-buck2-uses-gpio-dvs;
- max8997,pmic-buck5-uses-gpio-dvs;
-
- max8997,pmic-ignore-gpiodvs-side-effect;
- max8997,pmic-buck125-default-dvs-idx = <0>;
-
- max8997,pmic-buck125-dvs-gpios = <&gpx0 5 0>,
- <&gpx0 6 0>,
- <&gpl0 0 0>;
-
- max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
- <1250000>, <1200000>,
- <1150000>, <1100000>,
- <1000000>, <950000>;
-
- max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>,
- <950000>, <900000>,
- <1100000>, <1000000>,
- <950000>, <900000>;
-
- max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>,
- <1200000>, <1200000>,
- <1200000>, <1200000>,
- <1200000>, <1200000>;
-
- regulators {
- valive_reg: LDO2 {
- regulator-name = "VALIVE_1.1V_C210";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- };
-
- vusb_reg: LDO3 {
- regulator-name = "VUSB_1.1V_C210";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- };
-
- vmipi_reg: LDO4 {
- regulator-name = "VMIPI_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vpda_reg: LDO6 {
- regulator-name = "VCC_1.8V_PDA";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- vcam_reg: LDO7 {
- regulator-name = "CAM_ISP_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vusbdac_reg: LDO8 {
- regulator-name = "VUSB/VDAC_3.3V_C210";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- vccpda_reg: LDO9 {
- regulator-name = "VCC_2.8V_PDA";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- };
-
- vpll_reg: LDO10 {
- regulator-name = "VPLL_1.1V_C210";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- };
-
- vtcam_reg: LDO12 {
- regulator-name = "VT_CAM_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vcclcd_reg: LDO13 {
- regulator-name = "VCC_3.3V_LCD";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- vlcd_reg: LDO15 {
- regulator-name = "VLCD_2.2V";
- regulator-min-microvolt = <2200000>;
- regulator-max-microvolt = <2200000>;
- };
-
- camsensor_reg: LDO16 {
- regulator-name = "CAM_SENSOR_IO_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vddq_reg: LDO21 {
- regulator-name = "VDDQ_M1M2_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- varm_breg: BUCK1 {
- /*
- * HACK: The real name is VARM_1.2V_C210,
- * but exynos-cpufreq does not support
- * DT-based regulator lookup yet.
- */
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- };
-
- vint_breg: BUCK2 {
- regulator-name = "VINT_1.1V_C210";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- };
-
- camisp_breg: BUCK4 {
- regulator-name = "CAM_ISP_CORE_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- vmem_breg: BUCK5 {
- regulator-name = "VMEM_1.2V_C210";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- vccsub_breg: BUCK7 {
- regulator-name = "VCC_SUB_2.0V";
- regulator-min-microvolt = <2000000>;
- regulator-max-microvolt = <2000000>;
- regulator-always-on;
- };
-
- safe1_sreg: ESAFEOUT1 {
- regulator-name = "SAFEOUT1";
- regulator-always-on;
- };
-
- safe2_sreg: ESAFEOUT2 {
- regulator-name = "SAFEOUT2";
- regulator-boot-on;
- };
- };
- };
- };
-
fixed-rate-clocks {
xxti {
compatible = "samsung,clock-xxti";
@@ -365,71 +134,6 @@
};
};
- dsi_0: dsi at 11C80000 {
- vddcore-supply = <&vusb_reg>;
- vddio-supply = <&vmipi_reg>;
- samsung,pll-clock-frequency = <24000000>;
- status = "okay";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port at 1 {
- reg = <1>;
-
- dsi_out: endpoint {
- remote-endpoint = <&dsi_in>;
- samsung,burst-clock-frequency = <500000000>;
- samsung,esc-clock-frequency = <20000000>;
- };
- };
- };
-
- panel at 0 {
- reg = <0>;
- compatible = "samsung,s6e8aa0";
- vdd3-supply = <&vcclcd_reg>;
- vci-supply = <&vlcd_reg>;
- reset-gpios = <&gpy4 5 0>;
- power-on-delay= <50>;
- reset-delay = <100>;
- init-delay = <100>;
- flip-horizontal;
- flip-vertical;
- panel-width-mm = <58>;
- panel-height-mm = <103>;
-
- display-timings {
- timing-0 {
- clock-frequency = <57153600>;
- hactive = <720>;
- vactive = <1280>;
- hfront-porch = <5>;
- hback-porch = <5>;
- hsync-len = <5>;
- vfront-porch = <13>;
- vback-porch = <1>;
- vsync-len = <2>;
- };
- };
-
- port {
- dsi_in: endpoint {
- remote-endpoint = <&dsi_out>;
- };
- };
- };
- };
-
- fimd at 11c00000 {
- status = "okay";
- };
-
- tmu at 100C0000 {
- status = "okay";
- };
-
thermal-zones {
cpu_thermal: cpu-thermal {
cooling-maps {
@@ -483,3 +187,299 @@
};
};
};
+
+&dsi_0 {
+ vddcore-supply = <&vusb_reg>;
+ vddio-supply = <&vmipi_reg>;
+ samsung,pll-clock-frequency = <24000000>;
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 1 {
+ reg = <1>;
+
+ dsi_out: endpoint {
+ remote-endpoint = <&dsi_in>;
+ samsung,burst-clock-frequency = <500000000>;
+ samsung,esc-clock-frequency = <20000000>;
+ };
+ };
+ };
+
+ panel at 0 {
+ reg = <0>;
+ compatible = "samsung,s6e8aa0";
+ vdd3-supply = <&vcclcd_reg>;
+ vci-supply = <&vlcd_reg>;
+ reset-gpios = <&gpy4 5 0>;
+ power-on-delay= <50>;
+ reset-delay = <100>;
+ init-delay = <100>;
+ flip-horizontal;
+ flip-vertical;
+ panel-width-mm = <58>;
+ panel-height-mm = <103>;
+
+ display-timings {
+ timing-0 {
+ clock-frequency = <57153600>;
+ hactive = <720>;
+ vactive = <1280>;
+ hfront-porch = <5>;
+ hback-porch = <5>;
+ hsync-len = <5>;
+ vfront-porch = <13>;
+ vback-porch = <1>;
+ vsync-len = <2>;
+ };
+ };
+
+ port {
+ dsi_in: endpoint {
+ remote-endpoint = <&dsi_out>;
+ };
+ };
+ };
+};
+
+&exynos_usbphy {
+ status = "okay";
+};
+
+&fimd {
+ status = "okay";
+};
+
+&hsotg {
+ vusb_d-supply = <&vusb_reg>;
+ vusb_a-supply = <&vusbdac_reg>;
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&i2c_3 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <400000>;
+ pinctrl-0 = <&i2c3_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ mms114-touchscreen at 48 {
+ compatible = "melfas,mms114";
+ reg = <0x48>;
+ interrupt-parent = <&gpx0>;
+ interrupts = <4 2>;
+ x-size = <720>;
+ y-size = <1280>;
+ avdd-supply = <&tsp_reg>;
+ vdd-supply = <&tsp_reg>;
+ };
+};
+
+&i2c_5 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <100000>;
+ pinctrl-0 = <&i2c5_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ max8997_pmic at 66 {
+ compatible = "maxim,max8997-pmic";
+
+ reg = <0x66>;
+
+ max8997,pmic-buck1-uses-gpio-dvs;
+ max8997,pmic-buck2-uses-gpio-dvs;
+ max8997,pmic-buck5-uses-gpio-dvs;
+
+ max8997,pmic-ignore-gpiodvs-side-effect;
+ max8997,pmic-buck125-default-dvs-idx = <0>;
+
+ max8997,pmic-buck125-dvs-gpios = <&gpx0 5 0>,
+ <&gpx0 6 0>,
+ <&gpl0 0 0>;
+
+ max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
+ <1250000>, <1200000>,
+ <1150000>, <1100000>,
+ <1000000>, <950000>;
+
+ max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>,
+ <950000>, <900000>,
+ <1100000>, <1000000>,
+ <950000>, <900000>;
+
+ max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>;
+
+ regulators {
+ valive_reg: LDO2 {
+ regulator-name = "VALIVE_1.1V_C210";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ vusb_reg: LDO3 {
+ regulator-name = "VUSB_1.1V_C210";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ vmipi_reg: LDO4 {
+ regulator-name = "VMIPI_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vpda_reg: LDO6 {
+ regulator-name = "VCC_1.8V_PDA";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ vcam_reg: LDO7 {
+ regulator-name = "CAM_ISP_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vusbdac_reg: LDO8 {
+ regulator-name = "VUSB/VDAC_3.3V_C210";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vccpda_reg: LDO9 {
+ regulator-name = "VCC_2.8V_PDA";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ vpll_reg: LDO10 {
+ regulator-name = "VPLL_1.1V_C210";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ vtcam_reg: LDO12 {
+ regulator-name = "VT_CAM_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vcclcd_reg: LDO13 {
+ regulator-name = "VCC_3.3V_LCD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vlcd_reg: LDO15 {
+ regulator-name = "VLCD_2.2V";
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ };
+
+ camsensor_reg: LDO16 {
+ regulator-name = "CAM_SENSOR_IO_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vddq_reg: LDO21 {
+ regulator-name = "VDDQ_M1M2_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ varm_breg: BUCK1 {
+ /*
+ * HACK: The real name is VARM_1.2V_C210,
+ * but exynos-cpufreq does not support
+ * DT-based regulator lookup yet.
+ */
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ };
+
+ vint_breg: BUCK2 {
+ regulator-name = "VINT_1.1V_C210";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ camisp_breg: BUCK4 {
+ regulator-name = "CAM_ISP_CORE_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ vmem_breg: BUCK5 {
+ regulator-name = "VMEM_1.2V_C210";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ vccsub_breg: BUCK7 {
+ regulator-name = "VCC_SUB_2.0V";
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-always-on;
+ };
+
+ safe1_sreg: ESAFEOUT1 {
+ regulator-name = "SAFEOUT1";
+ regulator-always-on;
+ };
+
+ safe2_sreg: ESAFEOUT2 {
+ regulator-name = "SAFEOUT2";
+ regulator-boot-on;
+ };
+ };
+ };
+};
+
+&sdhci_0 {
+ bus-width = <8>;
+ non-removable;
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>;
+ pinctrl-names = "default";
+ vmmc-supply = <&vemmc_reg>;
+ status = "okay";
+};
+
+&serial_0 {
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&serial_2 {
+ status = "okay";
+};
+
+&serial_3 {
+ status = "okay";
+};
+
+&tmu {
+ status = "okay";
+};
--
2.1.0
More information about the linux-arm-kernel
mailing list