[PATCH 01/10] ARM: dts: apq8064: add RPM regulators support

[Bjorn Andersson]

On Thu 09 Apr 01:22 PDT 2015, Srinivas Kandagatla wrote:

> This patch adds rpm node to apq8064 dt as rpm would be used by other
> devices for regulator support. Also adds all the regulators in the rpm.
> 
> Most content of this patch was originally posted by Stephen Boyd on the
> list.
> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla at linaro.org>
> ---
>  arch/arm/boot/dts/qcom-apq8064.dtsi | 272 ++++++++++++++++++++++++++++++++++++
>  1 file changed, 272 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
> index 6c15112..d9166eb 100644
> --- a/arch/arm/boot/dts/qcom-apq8064.dtsi
> +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
> @@ -3,6 +3,7 @@
>  #include "skeleton.dtsi"
>  #include <dt-bindings/clock/qcom,gcc-msm8960.h>
>  #include <dt-bindings/clock/qcom,mmcc-msm8960.h>
> +#include <dt-bindings/mfd/qcom-rpm.h>
>  #include <dt-bindings/soc/qcom,gsbi.h>
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  
> @@ -276,6 +277,277 @@
>  			#reset-cells = <1>;
>  		};
>  
> +		l2cc: clock-controller at 2011000 {
> +			compatible	= "syscon";
> +			reg		= <0x2011000 0x1000>;
> +		};
> +
> +		rpm at 108000 {
> +			compatible	= "qcom,rpm-apq8064";
> +			reg		= <0x108000 0x1000>;
> +			qcom,ipc	= <&l2cc 0x8 2>;
> +
> +			interrupts	= <GIC_SPI 19 IRQ_TYPE_NONE>,
> +					  <GIC_SPI 21 IRQ_TYPE_NONE>,
> +					  <GIC_SPI 22 IRQ_TYPE_NONE>;

All three interrupts should be IRQ_TYPE_EDGE_RISING, currently the
driver overrides this with IRQF_TRIGGER_RISING but it should just obey
the dt.

> +			interrupt-names	= "ack", "err", "wakeup";
> +
> +			regulators {
> +				compatible = "qcom,rpm-pm8921-regulators";
> +				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
> +				vin_lvs1_3_6-supply = <&pm8921_s4>;
> +				vin_lvs2-supply = <&pm8921_s4>;
> +				vin_lvs4_5_7-supply = <&pm8921_s4>;
> +				vdd_ncp-supply = <&pm8921_l6>;
> +				vdd_l24-supply = <&pm8921_s1>;
> +				vdd_l25-supply = <&pm8921_s1>;
> +				vdd_l27-supply = <&pm8921_s7>;
> +				vdd_l28-supply = <&pm8921_s7>;

These are actually possible to change when designing a device, but
it's not unlikely that everyone have these values so they are reasonable
to have here.

But for several of the regulators we're running our 8064 devices with
different configuration, especially voltage, so I don't think they
should be specified here.

Having the phandles listed here are sane though, so that we can address
them from the platform files.

> +
> +				/* Buck SMPS */
> +				pm8921_s1: s1 {
> +					regulator-always-on;
> +					regulator-min-microvolt = <1225000>;
> +					regulator-max-microvolt = <1225000>;
> +					qcom,switch-mode-frequency = <3200000>;
> +					bias-pull-down;
> +				};
> +
[..]

Regards,
Bjorn