[PATCH v2 5/6] Documentation: dt-bindings: Add binding info for X-Gene QMTM UIO driver

[Ankit Jindal]

This patch adds device tree binding documentation for
X-Gene QMTM UIO driver.

Signed-off-by: Ankit Jindal <ankit.jindal at linaro.org>
Signed-off-by: Tushar Jagad <tushar.jagad at linaro.org>
---
 .../devicetree/bindings/uio/uio_xgene_qmtm.txt     |   53 ++++++++++++++++++++
 1 file changed, 53 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/uio/uio_xgene_qmtm.txt

diff --git a/Documentation/devicetree/bindings/uio/uio_xgene_qmtm.txt b/Documentation/devicetree/bindings/uio/uio_xgene_qmtm.txt
new file mode 100644
index 0000000..288ed92
--- /dev/null
+++ b/Documentation/devicetree/bindings/uio/uio_xgene_qmtm.txt
@@ -0,0 +1,53 @@
+APM X-Gene QMTM UIO nodes
+
+The Applied Micro X-Gene SOC has on-chip QMTM (Queue manager
+and Traffic manager). It is a device for managing hardware queues.
+It also implements QoS among hardware queues hence term "traffic"
+manager is present in its name. QMTM UIO nodes are defined for user
+space access to this device using UIO framework.
+
+Required properties:
+- compatible: Should be "apm,xgene-qmtm"
+- reg: Address and length of the register set for the device. It contains the
+  information of registers in the same order as described by reg-names.
+- reg-names: Should contain the register set names
+  - "csr": QMTM control and status register address space.
+  - "fabric": QMTM memory mapped access to queue states.
+- qpool: Points to the phandle of the node defining memory location for
+	 creating QMTM queues. This could point either to the reserved-memory
+	 node (as-per reserved memory bindings) or to the node of on-chip
+	 SRAM etc. It is expected that size and location of qpool memory will
+	 be configurable via bootloader.
+- clocks: Reference to the clock entry.
+- num-queues: Number of queues under this QMTM device.
+- devid: QMTM identification number for the system having multiple QMTM devices.
+	 This is used to form a unique id (a tuple of queue number and
+	 device id) for the queues belonging to this device.
+
+Example:
+	qmtm1_uio_qpool: qmtm1_uio_qpool {
+		reg = <0x0 0x0 0x0 0x0>
+	};
+
+	qmtm1clk: qmtmclk at 1f20c000 {
+		compatible = "apm,xgene-device-clock";
+		clock-output-names = "qmtm1clk";
+		status = "ok";
+	};
+
+	qmtm1_uio: qmtm_uio at 1f200000 {
+		compatible = "apm,xgene-qmtm";
+		status = "disabled";
+		reg = <0x0 0x1f200000 0x0 0x10000>,
+		      <0x0 0x1b000000 0x0 0x400000>;
+		reg-names = "csr", "fabric";
+		qpool = <&qmtm1_uio_qpool>;
+		clocks = <&qmtm1clk 0>;
+		num-queues = <0x400>;
+		devid = <1>;
+	};
+
+	/* Board-specific peripheral configurations */
+	&qmtm1_uio {
+		status = "ok";
+	};
-- 
1.7.9.5