[PATCH v4 1/4] pinctrl: imx: add gpio pinmux support for vf610

[Stefan Agner]

Add pinmux support for GPIO for Vybrid (vf610) IOMUX controller.
This is needed since direction configuration is not part of the
GPIO module in Vybrid.

Signed-off-by: Stefan Agner <stefan at agner.ch>
Acked-by: Shawn Guo <shawn.guo at freescale.com>
---
 drivers/pinctrl/freescale/pinctrl-imx.c | 72 +++++++++++++++++++++++++++++++++
 1 file changed, 72 insertions(+)

diff --git a/drivers/pinctrl/freescale/pinctrl-imx.c b/drivers/pinctrl/freescale/pinctrl-imx.c
index f244676..52f2b94 100644
--- a/drivers/pinctrl/freescale/pinctrl-imx.c
+++ b/drivers/pinctrl/freescale/pinctrl-imx.c
@@ -294,11 +294,83 @@ static int imx_pmx_get_groups(struct pinctrl_dev *pctldev, unsigned selector,
 	return 0;
 }
 
+static int imx_pmx_gpio_request_enable(struct pinctrl_dev *pctldev,
+			struct pinctrl_gpio_range *range, unsigned offset)
+{
+	struct imx_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev);
+	const struct imx_pinctrl_soc_info *info = ipctl->info;
+	const struct imx_pin_reg *pin_reg;
+	struct imx_pin_group *grp;
+	struct imx_pin *imx_pin;
+	unsigned int pin, group;
+	u32 reg;
+
+	/* Currently implementation only for shared mux/conf register */
+	if (!(info->flags & SHARE_MUX_CONF_REG))
+		return -EINVAL;
+
+	pin_reg = &info->pin_regs[offset];
+	if (pin_reg->mux_reg == -1)
+		return -EINVAL;
+
+	/* Find the pinctrl config with GPIO mux mode for the requested pin */
+	for (group = 0; group < info->ngroups; group++) {
+		grp = &info->groups[group];
+		for (pin = 0; pin < grp->npins; pin++) {
+			imx_pin = &grp->pins[pin];
+			if (imx_pin->pin == offset && !imx_pin->mux_mode)
+				goto mux_pin;
+		}
+	}
+
+	return -EINVAL;
+
+mux_pin:
+	reg = readl(ipctl->base + pin_reg->mux_reg);
+	reg &= ~(0x7 << 20);
+	reg |= imx_pin->config;
+	writel(reg, ipctl->base + pin_reg->mux_reg);
+
+	return 0;
+}
+
+static int imx_pmx_gpio_set_direction(struct pinctrl_dev *pctldev,
+	   struct pinctrl_gpio_range *range, unsigned offset, bool input)
+{
+	struct imx_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev);
+	const struct imx_pinctrl_soc_info *info = ipctl->info;
+	const struct imx_pin_reg *pin_reg;
+	u32 reg;
+
+	/*
+	 * Only Vybrid has the input/output buffer enable flags (IBE/OBE)
+	 * They are part of the shared mux/conf register.
+	 */
+	if (!(info->flags & SHARE_MUX_CONF_REG))
+		return -EINVAL;
+
+	pin_reg = &info->pin_regs[offset];
+	if (pin_reg->mux_reg == -1)
+		return -EINVAL;
+
+	/* IBE always enabled allows us to read the value "on the wire" */
+	reg = readl(ipctl->base + pin_reg->mux_reg);
+	if (input)
+		reg &= ~0x2;
+	else
+		reg |= 0x2;
+	writel(reg, ipctl->base + pin_reg->mux_reg);
+
+	return 0;
+}
+
 static const struct pinmux_ops imx_pmx_ops = {
 	.get_functions_count = imx_pmx_get_funcs_count,
 	.get_function_name = imx_pmx_get_func_name,
 	.get_function_groups = imx_pmx_get_groups,
 	.set_mux = imx_pmx_set,
+	.gpio_request_enable = imx_pmx_gpio_request_enable,
+	.gpio_set_direction = imx_pmx_gpio_set_direction,
 };
 
 static int imx_pinconf_get(struct pinctrl_dev *pctldev,
-- 
2.1.0