[PATCH 2/2] iommu/arm-smmu: add support for iova_to_phys through ATS1PR

[Will Deacon]

Hi Mitch,

On Thu, Sep 11, 2014 at 07:30:44PM +0100, Mitchel Humpherys wrote:
> Currently, we provide the iommu_ops.iova_to_phys service by doing a
> table walk in software to translate IO virtual addresses to physical
> addresses. On SMMUs that support it, it can be useful to ask the SMMU
> itself to do the translation. This can be used to warm the TLBs for an
> SMMU. It can also be useful for testing and hardware validation.
> 
> Since the address translation registers are optional on SMMUv2, only
> enable hardware translations when using SMMUv1 or when SMMU_IDR0.S1TS=1
> and SMMU_IDR0.ATOSNS=0, as described in the ARM SMMU v1-v2 spec.

[...]

> +static phys_addr_t arm_smmu_iova_to_phys_hard(struct iommu_domain *domain,
> +					dma_addr_t iova)
> +{
> +	struct arm_smmu_domain *smmu_domain = domain->priv;
> +	struct arm_smmu_device *smmu = smmu_domain->smmu;
> +	struct arm_smmu_cfg *cfg = &smmu_domain->cfg;
> +	struct device *dev = smmu->dev;
> +	void __iomem *cb_base;
> +	u32 tmp;
> +	u64 phys;
> +
> +	cb_base = ARM_SMMU_CB_BASE(smmu) + ARM_SMMU_CB(smmu, cfg->cbndx);
> +
> +	if (smmu->version == 1) {
> +		u32 reg = iova & ~0xFFF;
> +		writel_relaxed(reg, cb_base + ARM_SMMU_CB_ATS1PR_LO);
> +	} else {
> +		u32 reg = iova & ~0xFFF;
> +		writel_relaxed(reg, cb_base + ARM_SMMU_CB_ATS1PR_LO);
> +		reg = (iova & ~0xFFF) >> 32;
> +		writel_relaxed(reg, cb_base + ARM_SMMU_CB_ATS1PR_HI);
> +	}
> +
> +	if (readl_poll_timeout(cb_base + ARM_SMMU_CB_ATSR, tmp,
> +				!(tmp & ATSR_ACTIVE), 10, ATSR_LOOP_TIMEOUT)) {
> +		dev_err(dev,
> +			"iova to phys timed out on 0x%pa for %s. Falling back to software table walk.\n",
> +			&iova, dev_name(dev));

dev_err already prints the device name.

> +		return arm_smmu_iova_to_phys_soft(domain, iova);
> +	}
> +
> +	phys = readl_relaxed(cb_base + ARM_SMMU_CB_PAR_LO);
> +	phys |= ((u64) readl_relaxed(cb_base + ARM_SMMU_CB_PAR_HI)) << 32;
> +
> +	if (phys & CB_PAR_F) {
> +		dev_err(dev, "translation fault on %s!\n", dev_name(dev));
> +		dev_err(dev, "PAR = 0x%llx\n", phys);
> +	}
> +	phys = (phys & 0xFFFFFFF000ULL) | (iova & 0x00000FFF);

How does this work for 64k pages?

Will