[PATCH 5/6] ARM: dts: imx: ventana: cleanup pinctrl groups
Tim Harvey
tharvey at gateworks.com
Mon Sep 8 23:07:30 PDT 2014
Follow the conventions for pinctrl:
- grouping pinctrl in logical alphabatized groups
- remove any pinctrl not being used by a driver or needed by user
- move iomuxc to bottom of file for readability
Signed-off-by: Tim Harvey <tharvey at gateworks.com>
---
arch/arm/boot/dts/imx6q-gw5400-a.dts | 157 +++++++++++++-----------
arch/arm/boot/dts/imx6qdl-gw51xx.dtsi | 123 ++++++++++---------
arch/arm/boot/dts/imx6qdl-gw52xx.dtsi | 210 ++++++++++++++++---------------
arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 224 +++++++++++++++++----------------
arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 225 ++++++++++++++++++----------------
5 files changed, 491 insertions(+), 448 deletions(-)
diff --git a/arch/arm/boot/dts/imx6q-gw5400-a.dts b/arch/arm/boot/dts/imx6q-gw5400-a.dts
index eb28f63..822ffb2 100644
--- a/arch/arm/boot/dts/imx6q-gw5400-a.dts
+++ b/arch/arm/boot/dts/imx6q-gw5400-a.dts
@@ -38,6 +38,8 @@
leds {
compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
led0: user1 {
label = "user1";
@@ -65,6 +67,8 @@
pps {
compatible = "pps-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
status = "okay";
};
@@ -337,27 +341,64 @@
};
};
-&iomuxc {
+&ldb {
+ status = "okay";
+};
+
+&pcie {
+ reset-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ eth1: sky2 at 8 { /* MAC/PHY on bus 8 */
+ compatible = "marvell,sky2";
+ };
+};
+
+&ssi1 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hog>;
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+};
+
+&iomuxc {
imx6q-gw5400-a {
- pinctrl_hog: hoggrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x0001b0b0 /* OTG_PWR_EN */
- MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x0001b0b0 /* SPINOR_CS0# */
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x0001b0b0 /* PCIE IRQ */
- MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x0001b0b0 /* PCIE RST */
- MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000130b0 /* AUD4_MCK */
- MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x0001b0b0 /* GPS_PPS */
- MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x0001b0b0 /* TOUCH_IRQ# */
- MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x0001b0b0 /* user1 led */
- MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x0001b0b0 /* user2 led */
- MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x0001b0b0 /* user3 led */
- MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x4001b0b0 /* USBHUB_RST# */
- MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x4001b0b0 /* MIPI_DIO */
- >;
- };
pinctrl_audmux: audmuxgrp {
fsl,pins = <
@@ -365,6 +406,7 @@
MX6QDL_PAD_SD2_DAT3__AUD4_TXC 0x130b0
MX6QDL_PAD_SD2_DAT2__AUD4_TXD 0x110b0
MX6QDL_PAD_SD2_DAT1__AUD4_TXFS 0x130b0
+ MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0 /* AUD4_MCK */
>;
};
@@ -373,6 +415,7 @@
MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b0b0 /* SPINOR_CS0# */
>;
};
@@ -397,6 +440,14 @@
>;
};
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x1b0b0 /* user1 led */
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0 /* user2 led */
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b0 /* user3 led */
+ >;
+ };
+
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
@@ -418,6 +469,19 @@
>;
};
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b0 /* PCIE IRQ */
+ MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0 /* PCIE RST */
+ >;
+ };
+
+ pinctrl_pps: ppsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x1b0b0 /* GPS_PPS */
+ >;
+ };
+
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
@@ -442,6 +506,7 @@
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 /* OTG_PWR_EN */
>;
};
@@ -457,59 +522,3 @@
};
};
};
-
-&ldb {
- status = "okay";
-};
-
-&pcie {
- reset-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
- status = "okay";
-
- eth1: sky2 at 8 { /* MAC/PHY on bus 8 */
- compatible = "marvell,sky2";
- };
-};
-
-&ssi1 {
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- status = "okay";
-};
-
-&uart5 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart5>;
- status = "okay";
-};
-
-&usbotg {
- vbus-supply = <®_usb_otg_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg>;
- disable-over-current;
- status = "okay";
-};
-
-&usbh1 {
- vbus-supply = <®_usb_h1_vbus>;
- status = "okay";
-};
-
-&usdhc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc3>;
- cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
index 2853a10..f2867c4 100644
--- a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
@@ -27,6 +27,8 @@
leds {
compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
led0: user1 {
label = "user1";
@@ -48,6 +50,8 @@
pps {
compatible = "pps-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pps>;
gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
status = "okay";
};
@@ -163,24 +167,51 @@
status = "okay";
};
-&iomuxc {
+&pcie {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hog>;
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio1 0 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
- imx6qdl-gw51xx {
- pinctrl_hog: hoggrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x4001b0b0 /* MEZZ_DIO0 */
- MX6QDL_PAD_EIM_A20__GPIO2_IO18 0x4001b0b0 /* MEZZ_DIO1 */
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x0001b0b0 /* OTG_PWR_EN */
- MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x0001b0b0 /* GPS_PPS */
- MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x0001b0b0 /* PHY Reset */
- MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x0001b0b0 /* PCIE_RST# */
- MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x0001b0b0 /* user1 led */
- MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x0001b0b0 /* user2 led */
- >;
- };
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+&iomuxc {
+ imx6qdl-gw51xx {
pinctrl_enet: enetgrp {
fsl,pins = <
MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
@@ -199,6 +230,14 @@
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
+ MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x1b0b0 /* PHY Reset */
+ >;
+ };
+
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x1b0b0
+ MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x1b0b0
>;
};
@@ -244,6 +283,18 @@
>;
};
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_pps: ppsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b0b1
+ >;
+ };
+
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
@@ -275,48 +326,8 @@
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 /* OTG_PWR_EN */
>;
};
};
};
-
-&pcie {
- reset-gpio = <&gpio1 0 GPIO_ACTIVE_LOW>;
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- status = "okay";
-};
-
-&uart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart3>;
- status = "okay";
-};
-
-&uart5 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart5>;
- status = "okay";
-};
-
-&usbotg {
- vbus-supply = <®_usb_otg_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg>;
- disable-over-current;
- status = "okay";
-};
-
-&usbh1 {
- status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
index 26b1395..6d137b4 100644
--- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
@@ -36,6 +36,8 @@
leds {
compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
led0: user1 {
label = "user1";
@@ -63,6 +65,8 @@
pps {
compatible = "pps-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pps>;
gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
status = "okay";
};
@@ -233,39 +237,96 @@
};
};
-&iomuxc {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hog>;
+&ldb {
+ status = "okay";
- imx6qdl-gw52xx {
- pinctrl_hog: hoggrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x4001b0b0 /* MEZZ_DIO0 */
- MX6QDL_PAD_EIM_A20__GPIO2_IO18 0x4001b0b0 /* MEZZ_DIO1 */
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x0001b0b0 /* OTG_PWR_EN */
- MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x0001b0b0 /* VIDDEC_PDN# */
- MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x0001b0b0 /* PHY Reset */
- MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x0001b0b0 /* PCIE_RST# */
- MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x4001b0b0 /* GPS_PWDN */
- MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x0001b0b0 /* GPS_PPS */
- MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000130b0 /* AUD4_MCK */
- MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x4001b0b0 /* USB_SEL_PCI */
- MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x0001b0b0 /* TOUCH_IRQ# */
- MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x0001b0b0 /* user1 led */
- MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x0001b0b0 /* user2 led */
- MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x0001b0b0 /* user3 led */
- MX6QDL_PAD_SD2_CMD__GPIO1_IO11 0x0001b0b0 /* LVDS_TCH# */
- MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x0001b0b0 /* SD3_CD# */
- MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x4001b0b0 /* UART2_EN# */
- >;
+ lvds-channel at 0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ };
};
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm4>;
+ status = "okay";
+};
+
+&ssi1 {
+ fsl,mode = "i2s-slave";
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ cd-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+};
+
+&iomuxc {
+ imx6qdl-gw52xx {
pinctrl_audmux: audmuxgrp {
fsl,pins = <
MX6QDL_PAD_SD2_DAT0__AUD4_RXD 0x130b0
MX6QDL_PAD_SD2_DAT3__AUD4_TXC 0x130b0
MX6QDL_PAD_SD2_DAT2__AUD4_TXD 0x110b0
MX6QDL_PAD_SD2_DAT1__AUD4_TXFS 0x130b0
+ MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0 /* AUD4_MCK */
>;
};
@@ -287,6 +348,15 @@
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
+ MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x1b0b0 /* PHY Reset */
+ >;
+ };
+
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x1b0b0
+ MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x1b0b0
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b0
>;
};
@@ -332,6 +402,18 @@
>;
};
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0 /* PCIE_RST# */
+ >;
+ };
+
+ pinctrl_pps: ppsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b0b1
+ >;
+ };
+
pinctrl_pwm4: pwm4grp {
fsl,pins = <
MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
@@ -362,6 +444,7 @@
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 /* OTG_PWR_EN */
>;
};
@@ -373,85 +456,8 @@
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0 /* CD */
>;
};
};
};
-
-&ldb {
- status = "okay";
-
- lvds-channel at 0 {
- fsl,data-mapping = "spwg";
- fsl,data-width = <18>;
- status = "okay";
-
- display-timings {
- native-mode = <&timing0>;
- timing0: hsd100pxn1 {
- clock-frequency = <65000000>;
- hactive = <1024>;
- vactive = <768>;
- hback-porch = <220>;
- hfront-porch = <40>;
- vback-porch = <21>;
- vfront-porch = <7>;
- hsync-len = <60>;
- vsync-len = <10>;
- };
- };
- };
-};
-
-&pcie {
- reset-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
- status = "okay";
-};
-
-&pwm4 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm4>;
- status = "okay";
-};
-
-&ssi1 {
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- status = "okay";
-};
-
-&uart5 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart5>;
- status = "okay";
-};
-
-&usbotg {
- vbus-supply = <®_usb_otg_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg>;
- disable-over-current;
- status = "okay";
-};
-
-&usbh1 {
- status = "okay";
-};
-
-&usdhc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc3>;
- cd-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
index e6e298b..cade1bd 100644
--- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
@@ -37,6 +37,8 @@
leds {
compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
led0: user1 {
label = "user1";
@@ -64,6 +66,8 @@
pps {
compatible = "pps-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pps>;
gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
status = "okay";
};
@@ -240,41 +244,101 @@
};
};
-&iomuxc {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hog>;
+&ldb {
+ status = "okay";
- imx6qdl-gw53xx {
- pinctrl_hog: hoggrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x4001b0b0 /* PCIE6EXP_DIO0 */
- MX6QDL_PAD_EIM_A20__GPIO2_IO18 0x4001b0b0 /* PCIE6EXP_DIO1 */
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x0001b0b0 /* OTG_PWR_EN */
- MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x4001b0b0 /* GPS_SHDN */
- MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x0001b0b0 /* GPS_PPS */
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x0001b0b0 /* PCIE IRQ */
- MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x0001b0b0 /* PCIE RST */
- MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000130b0 /* AUD4_MCK */
- MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x4001b0b0 /* CAN_STBY */
- MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x0001b0b0 /* PMIC_IRQ# */
- MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x4001b0b0 /* HUB_RST# */
- MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x4001b0b0 /* PCIE_WDIS# */
- MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x0001b0b0 /* ACCEL_IRQ# */
- MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x0001b0b0 /* user1 led */
- MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x0001b0b0 /* USBOTG_OC# */
- MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x0001b0b0 /* user2 led */
- MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x0001b0b0 /* user3 led */
- MX6QDL_PAD_SD2_CMD__GPIO1_IO11 0x0001b0b0 /* TOUCH_IRQ# */
- MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x0001b0b0 /* SD3_DET# */
- >;
+ lvds-channel at 1 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ };
};
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ eth1: sky2 at 8 { /* MAC/PHY on bus 8 */
+ compatible = "marvell,sky2";
+ };
+};
+
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm4>;
+ status = "okay";
+};
+
+&ssi1 {
+ fsl,mode = "i2s-slave";
+ status = "okay";
+};
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ cd-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+};
+
+&iomuxc {
+ imx6qdl-gw53xx {
pinctrl_audmux: audmuxgrp {
fsl,pins = <
MX6QDL_PAD_SD2_DAT0__AUD4_RXD 0x130b0
MX6QDL_PAD_SD2_DAT3__AUD4_TXC 0x130b0
MX6QDL_PAD_SD2_DAT2__AUD4_TXD 0x110b0
MX6QDL_PAD_SD2_DAT1__AUD4_TXFS 0x130b0
+ MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0 /* AUD4_MCK */
>;
};
@@ -303,6 +367,15 @@
fsl,pins = <
MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b0b1
MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b0b1
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x4001b0b0 /* CAN_STBY */
+ >;
+ };
+
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x1b0b0
+ MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x1b0b0
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b0
>;
};
@@ -348,6 +421,19 @@
>;
};
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b0 /* PCIE IRQ */
+ MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0 /* PCIE RST */
+ >;
+ };
+
+ pinctrl_pps: ppsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b0b1
+ >;
+ };
+
pinctrl_pwm4: pwm4grp {
fsl,pins = <
MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
@@ -378,6 +464,8 @@
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 /* PWR_EN */
+ MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x1b0b0 /* OC */
>;
};
@@ -389,90 +477,8 @@
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0 /* CD */
>;
};
};
};
-
-&ldb {
- status = "okay";
-
- lvds-channel at 1 {
- fsl,data-mapping = "spwg";
- fsl,data-width = <18>;
- status = "okay";
-
- display-timings {
- native-mode = <&timing0>;
- timing0: hsd100pxn1 {
- clock-frequency = <65000000>;
- hactive = <1024>;
- vactive = <768>;
- hback-porch = <220>;
- hfront-porch = <40>;
- vback-porch = <21>;
- vfront-porch = <7>;
- hsync-len = <60>;
- vsync-len = <10>;
- };
- };
- };
-};
-
-&pcie {
- reset-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
- status = "okay";
-
- eth1: sky2 at 8 { /* MAC/PHY on bus 8 */
- compatible = "marvell,sky2";
- };
-};
-
-&pwm4 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm4>;
- status = "okay";
-};
-
-&ssi1 {
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- status = "okay";
-};
-
-&uart5 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart5>;
- status = "okay";
-};
-
-&usbotg {
- vbus-supply = <®_usb_otg_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg>;
- disable-over-current;
- status = "okay";
-};
-
-&usbh1 {
- vbus-supply = <®_usb_h1_vbus>;
- status = "okay";
-};
-
-&usdhc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc3>;
- cd-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
index a366a93..cf13239 100644
--- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
@@ -37,6 +37,8 @@
leds {
compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
led0: user1 {
label = "user1";
@@ -64,6 +66,8 @@
pps {
compatible = "pps-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pps>;
gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
status = "okay";
};
@@ -329,35 +333,106 @@
};
};
-&iomuxc {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hog>;
+&ldb {
+ status = "okay";
- imx6qdl-gw54xx {
- pinctrl_hog: hoggrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x0001b0b0 /* OTG_PWR_EN */
- MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x0001b0b0 /* SPINOR_CS0# */
- MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x0001b0b0 /* GPS_PPS */
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x0001b0b0 /* PCIE IRQ */
- MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x0001b0b0 /* PCIE RST */
- MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000130b0 /* AUD4_MCK */
- MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x4001b0b0 /* CAN_STBY */
- MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x0001b0b0 /* TOUCH_IRQ# */
- MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x0001b0b0 /* user1 led */
- MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x0001b0b0 /* user2 led */
- MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x0001b0b0 /* user3 led */
- MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x4001b0b0 /* USBHUB_RST# */
- MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x4001b0b0 /* MIPI_DIO */
- >;
+ lvds-channel at 1 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ };
};
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ eth1: sky2 at 8 { /* MAC/PHY on bus 8 */
+ compatible = "marvell,sky2";
+ };
+};
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm4>;
+ status = "okay";
+};
+
+&ssi1 {
+ fsl,mode = "i2s-slave";
+ status = "okay";
+};
+
+&ssi2 {
+ fsl,mode = "i2s-slave";
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ cd-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+};
+
+&iomuxc {
+ imx6qdl-gw54xx {
pinctrl_audmux: audmuxgrp {
fsl,pins = <
MX6QDL_PAD_SD2_DAT0__AUD4_RXD 0x130b0
MX6QDL_PAD_SD2_DAT3__AUD4_TXC 0x130b0
MX6QDL_PAD_SD2_DAT2__AUD4_TXD 0x110b0
MX6QDL_PAD_SD2_DAT1__AUD4_TXFS 0x130b0
+ MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0 /* AUD4_MCK */
>;
};
@@ -386,6 +461,15 @@
fsl,pins = <
MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b0b1
MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b0b1
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x4001b0b0 /* CAN_STBY */
+ >;
+ };
+
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x1b0b0
+ MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x1b0b0
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b0
>;
};
@@ -431,6 +515,19 @@
>;
};
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b0 /* PCIE IRQ */
+ MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0 /* PCIE RST */
+ >;
+ };
+
+ pinctrl_pps: ppsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b0b1
+ >;
+ };
+
pinctrl_pwm4: pwm4grp {
fsl,pins = <
MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
@@ -461,6 +558,7 @@
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 /* PWR_EN */
>;
};
@@ -476,90 +574,3 @@
};
};
};
-
-&ldb {
- status = "okay";
-
- lvds-channel at 1 {
- fsl,data-mapping = "spwg";
- fsl,data-width = <18>;
- status = "okay";
-
- display-timings {
- native-mode = <&timing0>;
- timing0: hsd100pxn1 {
- clock-frequency = <65000000>;
- hactive = <1024>;
- vactive = <768>;
- hback-porch = <220>;
- hfront-porch = <40>;
- vback-porch = <21>;
- vfront-porch = <7>;
- hsync-len = <60>;
- vsync-len = <10>;
- };
- };
- };
-};
-
-&pcie {
- reset-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
- status = "okay";
-
- eth1: sky2 at 8 { /* MAC/PHY on bus 8 */
- compatible = "marvell,sky2";
- };
-};
-
-&pwm4 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm4>;
- status = "okay";
-};
-
-&ssi1 {
- status = "okay";
-};
-
-&ssi2 {
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- status = "okay";
-};
-
-&uart5 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart5>;
- status = "okay";
-};
-
-&usbotg {
- vbus-supply = <®_usb_otg_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg>;
- disable-over-current;
- status = "okay";
-};
-
-&usbh1 {
- vbus-supply = <®_usb_h1_vbus>;
- status = "okay";
-};
-
-&usdhc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc3>;
- cd-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
-};
--
1.8.3.2
More information about the linux-arm-kernel
mailing list