[PATCH v2 1/5] of: Add descriptions of thermtrip properties to Tegra PMC bindings

[Mikko Perttunen]

Hi again!

I have fixed all other issues mentioned apart from this one. I can see 
three ways ahead:

1) Keep things as is. There is a slight possibility that in the future 
we will have a hardware configuration with multiple bus addresses and 
this will cause annoyance.
2) Keep things otherwise as is, but read the bus address from the 
thermtrip node. While at it, just have a reference to the the I2C bus 
rather than the PMIC in the bindings.
3) Create a new poweroff driver class with two operations: poweroff and 
get_i2c_command. The AS3722 poweroff "driver" is already separated from 
the MFD and would be relatively straightforward to port to a new driver 
subsystem. However, other PMICs we have, such as Palmas, don't do this 
and would require larger refactoring. TBH, this smells of 
overengineering to me.
4) Other ideas?

What is your opinion?

Cheers,
Mikko

On 08/21/2014 08:54 PM, Stephen Warren wrote:
> On 08/21/2014 10:53 AM, Thierry Reding wrote:
>> On Thu, Aug 21, 2014 at 09:38:29AM -0600, Stephen Warren wrote:
>>> On 08/21/2014 12:58 AM, Thierry Reding wrote:
>>>> On Wed, Aug 20, 2014 at 02:16:49PM -0600, Stephen Warren wrote:
>>>>> On 08/13/2014 06:41 AM, Mikko Perttunen wrote:
>>>>>> Hardware-triggered thermal reset requires configuring the I2C
>>>>>> reset procedure. This configuration is read from the device tree,
>>>>>> so document the relevant properties in the binding documentation.
>>>>>
>>>>>> diff --git
>>>>>> a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
>>>>>> b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
>
>>>>>> +- nvidia,pmu : Phandle to power management unit / PMIC handling
>>>>>> poweroff
>>>>>> +- nvidia,reg-addr : I2C register address to write poweroff
>>>>>> command to
>>>>>> +- nvidia,reg-data : Poweroff command to write to PMU
>>>>>
>>>>> Why are both the PMU/PMIC phandle and the register address/data
>>>>> required? I
>>>>> thought the purpose of having the phandle was to allow the register
>>>>> address
>>>>> and data to be queried from the PMU/PMIC driver.
>>>>>
>>>>> To me, it seems much simpler to get rid of the phandle and just
>>>>> hard-code
>>>>> the I2C bus number, address, and data into this node, rather than
>>>>> having to
>>>>> go query it from the PMU/PMIC driver, then find the I2C controller,
>>>>> then
>>>>> query it for its ID (and hope that all HW modules that talk to I2C
>>>>> controllers directly use the same numbering scheme...)
>>>>
>>>> I originally requested this to be changed. It seems wrong to duplicate
>>>> information about the PMIC in both the PMIC device tree node and the
>>>> i2c-thermtrip node if we can get the same information from the driver
>>>> directly (via the phandle). It certainly requires a little more code,
>>>> but at the advantage of not having to figure out the I2C controller
>>>> hardware number and I2C slave addresses when writing the i2c-thermtrip
>>>> node.
>>>
>>> I cant see that argument, but surely the PMIC driver can also supply the
>
> Oops, that was meant to be can not cant.
>
>>> "reg-addr" and "reg-data" values too, if it's already being queried
>>> for the
>>> I2C device address and bus number? The binding above appears to
>>> duplicate
>>> part of the information, while requiring querying of the other part.
>>
>> I suppose that could be done. It would take a new function to do that,
>> though, since I'm not aware of a generic mechanism to query this kind of
>> information from a PMIC (there's no generic PMIC API, either, so perhaps
>> it would be a good time to create one?). The I2C controller and I2C
>> slave are generic I2C properties, whereas the register and data to power
>> off the device are very device specific.
>
> I don't think it's possible to generically query an I2C device for its
> address from the struct i2c_device object; the code still needs to call
> a function in the PMIC driver to obtain this.
>
> That's because some I2C devices respond to multiple I2C addresses, and
> there's no guarantee that the one I2C address in the DT (and hence the
> struct i2c_device) is the address upon which the regulator function exists.
>
> grep for i2c_new_dummy in drivers/mfd and you'll find quite a few
> examples. The Atmel MXT touchpad/screen is another example.
> --
> To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html