[PATCH 3/3] ARM: imx: source gpt per clk from OSC for system timer

[Anson Huang]

On i.MX6Q TO > 1.0, i.MX6DL and i.MX6SX, gpt per clock
can be from OSC instead of ipg_per, as ipg_per's rate
may be scaled when system enter low bus mode, to keep
system timer NOT drift, better to make gpt per clock
at fixed rate, here add support for gpt per clock to
be from OSC which is at fixed rate always.

There are some difference on this implementation of
gpt per clock source, see below for details:

i.MX6Q TO > 1.0: GPT_CR_CLKSRC, 3b'101 selects fix clock
    of OSC / 8 for gpt per clk;
i.MX6DL and i.MX6SX: GPT_CR_CLKSRC, 3b'101 selects OSC
    for gpt per clk, and we must enable GPT_CR_24MEM to
    enable OSC clk source for gpt per, GPT_PR_PRESCALER24M
    is for pre-scaling of this OSC clk, here set it to 8
    to make gpt per clk is 3MHz;
i.MX6SL: ipg_per can be from OSC directly, so no need to
    implement this new clk source for gpt per.

Signed-off-by: Anson Huang <b20788 at freescale.com>
---
 arch/arm/mach-imx/time.c |   29 ++++++++++++++++++++++++-----
 1 file changed, 24 insertions(+), 5 deletions(-)

diff --git a/arch/arm/mach-imx/time.c b/arch/arm/mach-imx/time.c
index bf92e5a..54d23c7 100644
--- a/arch/arm/mach-imx/time.c
+++ b/arch/arm/mach-imx/time.c
@@ -60,11 +60,15 @@
 #define MX2_TSTAT_CAPT		(1 << 1)
 #define MX2_TSTAT_COMP		(1 << 0)
 
-/* MX31, MX35, MX25, MX5 */
+/* MX31, MX35, MX25, MX5, MX6 */
 #define V2_TCTL_WAITEN		(1 << 3) /* Wait enable mode */
 #define V2_TCTL_CLK_IPG		(1 << 6)
 #define V2_TCTL_CLK_PER		(2 << 6)
+#define V2_TCTL_CLK_OSC_DIV8	(5 << 6)
+#define V2_TCTL_CLK_OSC		(7 << 6)
 #define V2_TCTL_FRR		(1 << 9)
+#define V2_TCTL_24MEN		(1 << 10)
+#define V2_TPRER_PRE24M		12
 #define V2_IR			0x0c
 #define V2_TSTAT		0x08
 #define V2_TSTAT_OF1		(1 << 0)
@@ -293,7 +297,7 @@ static int __init mxc_clockevent_init(struct clk *timer_clk)
 static void __init _mxc_timer_init(int irq,
 				   struct clk *clk_per, struct clk *clk_ipg)
 {
-	uint32_t tctl_val;
+	uint32_t tctl_val, tprer_val;
 
 	if (IS_ERR(clk_per)) {
 		pr_err("i.MX timer: unable to get clk\n");
@@ -312,10 +316,25 @@ static void __init _mxc_timer_init(int irq,
 	__raw_writel(0, timer_base + MXC_TCTL);
 	__raw_writel(0, timer_base + MXC_TPRER); /* see datasheet note */
 
-	if (timer_is_v2())
-		tctl_val = V2_TCTL_CLK_PER | V2_TCTL_FRR | V2_TCTL_WAITEN | MXC_TCTL_TEN;
-	else
+	if (timer_is_v2()) {
+		if ((cpu_is_imx6q() && imx_get_soc_revision() >
+			IMX_CHIP_REVISION_1_0) || cpu_is_imx6dl() ||
+			cpu_is_imx6sx()) {
+			tctl_val = V2_TCTL_CLK_OSC_DIV8 | V2_TCTL_FRR |
+				V2_TCTL_WAITEN | MXC_TCTL_TEN;
+			if (cpu_is_imx6dl() || cpu_is_imx6sx()) {
+				/* 24 / 8 = 3 MHz */
+				tprer_val = 7 << V2_TPRER_PRE24M;
+				__raw_writel(tprer_val, timer_base + MXC_TPRER);
+				tctl_val |= V2_TCTL_24MEN;
+			}
+		} else {
+			tctl_val = V2_TCTL_CLK_PER | V2_TCTL_FRR |
+				V2_TCTL_WAITEN | MXC_TCTL_TEN;
+		}
+	} else {
 		tctl_val = MX1_2_TCTL_FRR | MX1_2_TCTL_CLK_PCLK1 | MXC_TCTL_TEN;
+	}
 
 	__raw_writel(tctl_val, timer_base + MXC_TCTL);
 
-- 
1.7.9.5